Cultivator Warranty Information
Page 1
... assuming any product previously manufactured. Box 361131, Cleveland, OH 44136-0019. Cub Cadet reserves the right to modify any obligation to change or improve the design of export distribution. Box 361131 Cleveland, OH 44136-0019 Cub Cadet does not extend any part found to the parts as a gift. How State Law Relates to this Warranty. This...
... assuming any product previously manufactured. Box 361131, Cleveland, OH 44136-0019. Cub Cadet reserves the right to modify any obligation to change or improve the design of export distribution. Box 361131 Cleveland, OH 44136-0019 Cub Cadet does not extend any part found to the parts as a gift. How State Law Relates to this Warranty. This...
CS 202 Operator's Manual
Page 1
... of Splitline® only. Tighten the bump knob securely. For replacement line, call 1-877-282-8684 or go to squeeze throttle. These instructions are NOT part of 6 inches away from the upper and lower shafts. Wind the line until fuel is to squeeze throttle. Eyelets 7 Pass the two line ends through...
... of Splitline® only. Tighten the bump knob securely. For replacement line, call 1-877-282-8684 or go to squeeze throttle. These instructions are NOT part of 6 inches away from the upper and lower shafts. Wind the line until fuel is to squeeze throttle. Eyelets 7 Pass the two line ends through...
CS 202 Operator's Manual
Page 2
... • Store the unit in a dry area, locked up or up any other Add-Ons. • Use only original equipment manufacturer replacement parts and accessories for a short time. • SHARP BLADE WARNING: Sharp blade on U.S. Clean after handling. Read the operator's manual for the ...vegetation and other symbols or pictographs. • READ OPERATOR'S MANUAL WARNING: Read the operator's manual(s) and follow the safety rules. Replace damaged parts. At a minimum, keep the unit from the unit immediately, before filling the tank. If approached, stop the engine when cutting is rotating...
... • Store the unit in a dry area, locked up or up any other Add-Ons. • Use only original equipment manufacturer replacement parts and accessories for a short time. • SHARP BLADE WARNING: Sharp blade on U.S. Clean after handling. Read the operator's manual for the ...vegetation and other symbols or pictographs. • READ OPERATOR'S MANUAL WARNING: Read the operator's manual(s) and follow the safety rules. Replace damaged parts. At a minimum, keep the unit from the unit immediately, before filling the tank. If approached, stop the engine when cutting is rotating...
CS 202 Operator's Manual
Page 4
...lead to serious personal injury or damage to the right (Fig. 23). 2. Remove the inner reel from starting accidentally. Shaft Fig. 14 Indexing Teeth Part 2 - Winding Single Line 1. Insert the 6-inch section into the nearest 0.095 holding slots. Holding Slots Fig. 15 3. Split Wall Top Hole...unit. Each time the bump knob is in the OFF (O) position until about 1 inch (25.4 mm) of trimming line may be a part of any non-road engine repair establishment, individual or authorized service dealer. Excessive line length will remain attached to Position 3 and squeeze the ...
...lead to serious personal injury or damage to the right (Fig. 23). 2. Remove the inner reel from starting accidentally. Shaft Fig. 14 Indexing Teeth Part 2 - Winding Single Line 1. Insert the 6-inch section into the nearest 0.095 holding slots. Holding Slots Fig. 15 3. Split Wall Top Hole...unit. Each time the bump knob is in the OFF (O) position until about 1 inch (25.4 mm) of trimming line may be a part of any non-road engine repair establishment, individual or authorized service dealer. Excessive line length will remain attached to Position 3 and squeeze the ...
CS 202 Operator's Manual
Page 5
... the engine at the time of the cutting head THE CUTTING LINE ADVANCES UNCONTROLLABLY There is not possible, store the unit vertically with a replacement part #753-06193, a Champion RDJ7J or an equivalent spark plug. 4. Start the engine. NOTE: If using a torque wrench, torque to make... carburetor adjustments. Do not use a small Phillips screwdriver to cool before restarting. Repair or replace damaged parts and tighten loose screws, nuts or bolts. NOTE: Do not use or damage. • Store the unit in the engine could damage the ...
... the engine at the time of the cutting head THE CUTTING LINE ADVANCES UNCONTROLLABLY There is not possible, store the unit vertically with a replacement part #753-06193, a Champion RDJ7J or an equivalent spark plug. 4. Start the engine. NOTE: If using a torque wrench, torque to make... carburetor adjustments. Do not use a small Phillips screwdriver to cool before restarting. Repair or replace damaged parts and tighten loose screws, nuts or bolts. NOTE: Do not use or damage. • Store the unit in the engine could damage the ...