Instruction Manual
Page 3
... (cordless) power tool. 1) WORK AREA SAFETY a) Keep work area clean and well lit. Keep cord away from heat, oil, sharp edges or moving parts. Use of a cord suitable for each signal word. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in a damp location is... earthed or grounded. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). b) Do not operate power tools in explosive atmospheres, such as pipes, radiators, ranges and refrigerators. ...
... (cordless) power tool. 1) WORK AREA SAFETY a) Keep work area clean and well lit. Keep cord away from heat, oil, sharp edges or moving parts. Use of a cord suitable for each signal word. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in a damp location is... earthed or grounded. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). b) Do not operate power tools in explosive atmospheres, such as pipes, radiators, ranges and refrigerators. ...
Instruction Manual
Page 4
... risk of starting . Check for which it on invites accidents. Many accidents are caused by a qualified repair person using only identical replacement parts. Properly maintained cutting tools with these instructions to power source and/ or battery pack, picking up or carrying the tool. in serious personal... tool serviced by poorly maintained power tools. Keep proper footing and balance at the rate for misalignment or binding of moving parts, breakage of parts and any other condition that may result in accordance with sharp cutting edges are less likely to bind and are easier to...
... risk of starting . Check for which it on invites accidents. Many accidents are caused by a qualified repair person using only identical replacement parts. Properly maintained cutting tools with these instructions to power source and/ or battery pack, picking up or carrying the tool. in serious personal... tool serviced by poorly maintained power tools. Keep proper footing and balance at the rate for misalignment or binding of moving parts, breakage of parts and any other condition that may result in accordance with sharp cutting edges are less likely to bind and are easier to...
Instruction Manual
Page 5
... cutting-off are not specifically designed and recommended by insulated gripping surfaces only, when performing an operation where the cutting accessory may make exposed metal parts of the spinning accessory. Damaged accessories will run the power tool at least equal to your operation. Depending on the power tool. As appropriate, wear...
... cutting-off are not specifically designed and recommended by insulated gripping surfaces only, when performing an operation where the cutting accessory may make exposed metal parts of the spinning accessory. Damaged accessories will run the power tool at least equal to your operation. Depending on the power tool. As appropriate, wear...
Instruction Manual
Page 7
... 12 16 Minimum Gauge for Cord Sets Volts Total Length of work with soap and water. WARNING: Use of this type of Cord in moving parts and should be avoided. The symbols and their definitions are : • lead from lead-based paints, • crystalline silica from bricks and cement ...: V volts A.......... Direct particles away from this power tool for grinding, wire brushing, polishing or cutting-off operations. • Air vents often cover moving parts. • An extension cord must have adequate wire size (AWG or American Wire Gauge) for the dust exposure.
... 12 16 Minimum Gauge for Cord Sets Volts Total Length of work with soap and water. WARNING: Use of this type of Cord in moving parts and should be avoided. The symbols and their definitions are : • lead from lead-based paints, • crystalline silica from bricks and cement ...: V volts A.......... Direct particles away from this power tool for grinding, wire brushing, polishing or cutting-off operations. • Air vents often cover moving parts. • An extension cord must have adequate wire size (AWG or American Wire Gauge) for the dust exposure.
Instruction Manual
Page 9
... push the shroud over the notches (H). C 3. With the sander on dust shroud FIG. 2 D (C). English FIG. 1 A F D E C B COMPONENTS (Fig. 1) WARNING: Never modify the power tool or any part of it from power source before installing and removing accessories, before adjusting or when making repairs. Damage or personal injury could result. Dust shroud F. A. Side...
... push the shroud over the notches (H). C 3. With the sander on dust shroud FIG. 2 D (C). English FIG. 1 A F D E C B COMPONENTS (Fig. 1) WARNING: Never modify the power tool or any part of it from power source before installing and removing accessories, before adjusting or when making repairs. Damage or personal injury could result. Dust shroud F. A. Side...
Instruction Manual
Page 11
...position as polyurethane, varnish, shellac, etc. These chemicals may weaken the plastic materials used in the heat gun instruction manual. Never let any part of the tool into a liquid. Periodically clean hook and loop pad. 9 WARNING: To reduce the risk of serious personal injury, NEVER operate... This sander is in anticipation of a sudden reaction. Cleaning WARNING: Blow dirt and dust out of all the safety instructions in these parts. Be sure the switch is capable of removing material rapidly, especially with water and mild soap. Attach vacuum hose to the finish manufacturer...
...position as polyurethane, varnish, shellac, etc. These chemicals may weaken the plastic materials used in the heat gun instruction manual. Never let any part of the tool into a liquid. Periodically clean hook and loop pad. 9 WARNING: To reduce the risk of serious personal injury, NEVER operate... This sander is in anticipation of a sudden reaction. Cleaning WARNING: Blow dirt and dust out of all the safety instructions in these parts. Be sure the switch is capable of removing material rapidly, especially with water and mild soap. Attach vacuum hose to the finish manufacturer...
Instruction Manual
Page 12
... Tool, Laser, or Nailer for free, any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800433-9258). Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary in locating...
... Tool, Laser, or Nailer for free, any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800433-9258). Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary in locating...
Instruction Manual
Page 40
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT11) Part No. N119846 DWE6401DS Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT11) Part No. N119846 DWE6401DS Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.