Manual/User Guide
Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E144 C141-E202-01EN 3-1 For information about handling this hard disk drive and the system installation procedure, refer to the following Integration Guide.
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E144 C141-E202-01EN 3-1 For information about handling this hard disk drive and the system installation procedure, refer to the following Integration Guide.
Manual/User Guide
Page 11
3.4 Jumper Settings 3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the jumpers to select drive configuration and functions. Figure 3.11 Jumper location C141-E202-01EN 3-11 Figure 3.10 Power supply connector pins (CN1) 3.4 Jumper Settings 3.4.1 Location of setting jumpers Figure 3.11 shows the location of the power supply connector (CN1).
3.4 Jumper Settings 3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the jumpers to select drive configuration and functions. Figure 3.11 Jumper location C141-E202-01EN 3-11 Figure 3.10 Power supply connector pins (CN1) 3.4 Jumper Settings 3.4.1 Location of setting jumpers Figure 3.11 shows the location of the power supply connector (CN1).
Manual/User Guide
Page 12
Installation Conditions 3.4.2 Factory default setting Figure 3.12 shows the default setting position at the factory. Open 1 CA 2 DB Open (a) Master drive 1 CA Open Short 2 DB (b) Slave drive Figure 3.13 Jumper setting of master or slave drive Note: Pins A and C should be open. 3-12 C141-E202-01EN Open Figure 3.12 Factory default setting 3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected.
Installation Conditions 3.4.2 Factory default setting Figure 3.12 shows the default setting position at the factory. Open 1 CA 2 DB Open (a) Master drive 1 CA Open Short 2 DB (b) Slave drive Figure 3.13 Jumper setting of master or slave drive Note: Pins A and C should be open. 3-12 C141-E202-01EN Open Figure 3.12 Factory default setting 3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected.
Manual/User Guide
Page 13
... not connected to the CSEL conductor, the CSEL is identified as a master drive. 3.4.4 CSEL setting Figure 3.14 shows the cable select (CSEL) setting. 3.4 Jumper Settings Open 1 CA 2 DB Short Note: The CSEL setting is set to low level. Figure 3.14 CSEL setting Figure 3.15 and 3.16 show examples of the cable and connecting it to ground further, the...
... not connected to the CSEL conductor, the CSEL is identified as a master drive. 3.4.4 CSEL setting Figure 3.14 shows the cable select (CSEL) setting. 3.4 Jumper Settings Open 1 CA 2 DB Short Note: The CSEL setting is set to low level. Figure 3.14 CSEL setting Figure 3.15 and 3.16 show examples of the cable and connecting it to ground further, the...