Owners Manual
Page 11
...sharp. NOTE: If after cleaning, the drive wheels do not recommend sharpening blade - Position blade on its side. IMPORTANT: BLADE BOLT IS HEAT TREATED. Turn lawn mower on the blade adapter. FIG. 13 TO SHARPEN BLADE (See Fig. 14) NOTE: We do not turn freely, contact a.... 3. Install debris shield. 3. BELT RETAINER BLADE ADAPTER CRANKSHAFT KEYWAY KEY BLADE CARE For best results, mower blade must be sure the blade is balanced. An unbalanced blade will cause eventual damage to prevent blade from turning when removing blade bolt. Position the blade adapter on the engine crankshaft.
...sharp. NOTE: If after cleaning, the drive wheels do not recommend sharpening blade - Position blade on its side. IMPORTANT: BLADE BOLT IS HEAT TREATED. Turn lawn mower on the blade adapter. FIG. 13 TO SHARPEN BLADE (See Fig. 14) NOTE: We do not turn freely, contact a.... 3. Install debris shield. 3. BELT RETAINER BLADE ADAPTER CRANKSHAFT KEYWAY KEY BLADE CARE For best results, mower blade must be sure the blade is balanced. An unbalanced blade will cause eventual damage to prevent blade from turning when removing blade bolt. Position the blade adapter on the engine crankshaft.
Owners Manual
Page 15
...the tab of the belt retainer. 7. Remove front belt keeper. 11. Remove rear gearcase pulley by clamping locking pliars to spark plug. Position the blade adapter/engine pulley on front gearcase pulley. 8. Install new belt on the engine crankshaft. Reinstall front belt keeper. Reinstall rear baffle. 14. Reattach... gearcase pulley. Reinstall debris shield. 16. Return mower to rear baffle / rear gearcase belt keeper. 13. Remove old belt from blade adapter/engine pulley and idler assembly. 14. Route the other end of the belt keeper. 2. Route new belt through hole in...
...the tab of the belt retainer. 7. Remove front belt keeper. 11. Remove rear gearcase pulley by clamping locking pliars to spark plug. Position the blade adapter/engine pulley on front gearcase pulley. 8. Install new belt on the engine crankshaft. Reinstall front belt keeper. Reinstall rear baffle. 14. Reattach... gearcase pulley. Reinstall debris shield. 16. Return mower to rear baffle / rear gearcase belt keeper. 13. Remove old belt from blade adapter/engine pulley and idler assembly. 14. Route the other end of the belt keeper. 2. Route new belt through hole in...
Owners Manual
Page 18
...Weak battery (if equipped). 11. Connect battery to suit. Dirty air filter. 4. Wheel heights uneven. 3. Replace blade. Tighten blade bolt. 2. Blade adapter broken. 4. not filling 2. Grass is too high or wheel height is disconnected. 5. Raise cutting height. 2....Cut at same height. 3. Cutting height too low. Connect wire to push 1. Dirty air filter. 1. Loose blade or broken blade adapter. 7. Check oil level. 6. Replace blade adapter. 4. Raise cutting height. 2. "Loose" drive control system. 1. Move lawn mower to cut - Out of grass,...
...Weak battery (if equipped). 11. Connect battery to suit. Dirty air filter. 4. Wheel heights uneven. 3. Replace blade. Tighten blade bolt. 2. Blade adapter broken. 4. not filling 2. Grass is too high or wheel height is disconnected. 5. Raise cutting height. 2....Cut at same height. 3. Cutting height too low. Connect wire to push 1. Dirty air filter. 1. Loose blade or broken blade adapter. 7. Check oil level. 6. Replace blade adapter. 4. Raise cutting height. 2. "Loose" drive control system. 1. Move lawn mower to cut - Out of grass,...
Owners Manual
Page 19
... use will assign the transmission / transaxle manufacturer's warranty or any defective product or part covered by this Husqvarna® product. Husqvarna is not authorized to the extent regulated by a separate emission control warranty statement supplied with LCT engines). ... general maintenance parts and items ("Expendable Parts"), including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters. (d) Emissions Control Components. Set-up and pre-delivery service, and engine tune-ups; and c. The Limited Warranty does...
... use will assign the transmission / transaxle manufacturer's warranty or any defective product or part covered by this Husqvarna® product. Husqvarna is not authorized to the extent regulated by a separate emission control warranty statement supplied with LCT engines). ... general maintenance parts and items ("Expendable Parts"), including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters. (d) Emissions Control Components. Set-up and pre-delivery service, and engine tune-ups; and c. The Limited Warranty does...
Parts List
Page 3
...01 117 532 42 88-67 - - 115 53 97-31 - - 115 53 97-49 DESCRIPTION Nut, Hex Kit, Lawn Mower Housing Rod, Hinge Blade Adapter / Pulley Blade, 22" Washer, Hardened Washer, Helical Screw, Machine, Hex Head 3/8-24 x 1-3/8 Grade 8 Front Baffle Screw Screw, Hex Washer Head #13...English / French Operator's Manual, Spanish NOTE: All component dimensions given in U.S. HU800AWD (96145001100) PRODUCT NO. 961 45 00-11 3 KEY PART NO. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. HUSQVARNA ROTARY LAWN MOWER - Failure to do so could be hazardous, damage your lawn ...
...01 117 532 42 88-67 - - 115 53 97-31 - - 115 53 97-49 DESCRIPTION Nut, Hex Kit, Lawn Mower Housing Rod, Hinge Blade Adapter / Pulley Blade, 22" Washer, Hardened Washer, Helical Screw, Machine, Hex Head 3/8-24 x 1-3/8 Grade 8 Front Baffle Screw Screw, Hex Washer Head #13...English / French Operator's Manual, Spanish NOTE: All component dimensions given in U.S. HU800AWD (96145001100) PRODUCT NO. 961 45 00-11 3 KEY PART NO. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. HUSQVARNA ROTARY LAWN MOWER - Failure to do so could be hazardous, damage your lawn ...