Owner's Manual (pdf)
Page 1
...installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the spaces designated on the product. XR-1S KAC-X1D MONO DIGITAL POWER AMPLIFIER 3 page 2-13 INSTRUCTION MANUAL AMPLIFICATEUR MONO NUMÉRIQUE 3 page 14-25 MODE D'EMPLOI ...DIGITAL MONOFÓNICO 3 página 26-36 MANUAL DE INSTRUCCIONES Take the time to the model and serial numbers whenever you obtain the best performance from your new power amplifier. For your Kenwood product at www.Kenwoodusa.com © B64-4327-00/00 (KV/EV) Refer ...
...installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the spaces designated on the product. XR-1S KAC-X1D MONO DIGITAL POWER AMPLIFIER 3 page 2-13 INSTRUCTION MANUAL AMPLIFICATEUR MONO NUMÉRIQUE 3 page 14-25 MODE D'EMPLOI ...DIGITAL MONOFÓNICO 3 página 26-36 MANUAL DE INSTRUCCIONES Take the time to the model and serial numbers whenever you obtain the best performance from your new power amplifier. For your Kenwood product at www.Kenwoodusa.com © B64-4327-00/00 (KV/EV) Refer ...
Owner's Manual (pdf)
Page 2
...NOTE This Class B digital apparatus complies with regard to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg ...the following precautions: • Be sure the unit is connected to a 12V DC power supply with a negative ground connection. • Do not open the top or bottom...turn off and on a circuit different from that interference will not occur in the instruction manual. FCC NOTE This equipment has been tested and found to comply with the limits for ...
...NOTE This Class B digital apparatus complies with regard to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg ...the following precautions: • Be sure the unit is connected to a 12V DC power supply with a negative ground connection. • Do not open the top or bottom...turn off and on a circuit different from that interference will not occur in the instruction manual. FCC NOTE This equipment has been tested and found to comply with the limits for ...
Owner's Manual (pdf)
Page 4
Connect the speaker wires. 5. Install the installation fittings in the below locations; (Unstable location, In a location that ...side such as the brake lamps, turn signal lamps and windshield wipers operate normally. Install the amplifier in a place where the cooling fan and ducts of the units. 4. Otherwise heat build-...) 1 Hexagon Wrench (Small) 1 Terminal cover (Power terminal) 1 7 Installation procedure Since there are large variety of settings and connections possible according to applications, read the instruction manual well to the intended usage. 3. Set the unit...
Connect the speaker wires. 5. Install the installation fittings in the below locations; (Unstable location, In a location that ...side such as the brake lamps, turn signal lamps and windshield wipers operate normally. Install the amplifier in a place where the cooling fan and ducts of the units. 4. Otherwise heat build-...) 1 Hexagon Wrench (Small) 1 Terminal cover (Power terminal) 1 7 Installation procedure Since there are large variety of settings and connections possible according to applications, read the instruction manual well to the intended usage. 3. Set the unit...
Owner's Manual (pdf)
Page 10
... the LINE OUT FILTER switch from the LINE IN terminal is different in the instruction manual of 2 ohm, connect speakers with the LINE OUT FILTER switch will be reproduced even...or higher impedance to the in ON and OFF position. NOTE For the pre-output level, refer to these terminals. 6 REMOTE terminal Connects the Remote cable. LPF(Low-Pass Filter) FREQUENCY...; 2) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Power control terminal Controls the unit ON/OFF. CAUTION The volume of the audio output to the LINE ...
... the LINE OUT FILTER switch from the LINE IN terminal is different in the instruction manual of 2 ohm, connect speakers with the LINE OUT FILTER switch will be reproduced even...or higher impedance to the in ON and OFF position. NOTE For the pre-output level, refer to these terminals. 6 REMOTE terminal Connects the Remote cable. LPF(Low-Pass Filter) FREQUENCY...; 2) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Power control terminal Controls the unit ON/OFF. CAUTION The volume of the audio output to the LINE ...