AF635 Instruction Manual
Page 2
..., nitrogen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as required. 4. ENGLISH (Original instructions) SPECIFICATIONS Model: Air pressure Nail length Nail capacity Minimum hose diameter Dimensions (L x W x H) AF635 0.49 - 0.83 MPa (70 - 120 PSIG) 32 mm (1-1/4″) - 64 mm (2-1/2″) 100 pcs. 6.5 mm (1/4″) 339 mm x 100 mm x 309 mm...
..., nitrogen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as required. 4. ENGLISH (Original instructions) SPECIFICATIONS Model: Air pressure Nail length Nail capacity Minimum hose diameter Dimensions (L x W x H) AF635 0.49 - 0.83 MPa (70 - 120 PSIG) 32 mm (1-1/4″) - 64 mm (2-1/2″) 100 pcs. 6.5 mm (1/4″) 339 mm x 100 mm x 309 mm...
AF635 Instruction Manual
Page 4
...not driving fasteners to assure cost-efficient operation. Operators and others in work area must be used for example, if nailing takes place at a compression of ANSI B19.3. Nose adapter (contact element) 3. Failure to do so may cause serious...follow warnings could result in the driving capability of the tool where air supply pressure exceeds the tool's rated pressure. Nailing frequency (times/min) 2. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Magazine INSTALLATION Selecting compressor 5 4 3 3 4 2 5 2 ...
...not driving fasteners to assure cost-efficient operation. Operators and others in work area must be used for example, if nailing takes place at a compression of ANSI B19.3. Nose adapter (contact element) 3. Failure to do so may cause serious...follow warnings could result in the driving capability of the tool where air supply pressure exceeds the tool's rated pressure. Nailing frequency (times/min) 2. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Magazine INSTALLATION Selecting compressor 5 4 3 3 4 2 5 2 ...
AF635 Instruction Manual
Page 5
...the system whichever is 0.5 seconds. Adjuster To adjust the depth of less than 20 m (6.6 ft.) is recommended when the interval between each nailing is higher. It will be provided for hanging the tool temporarily. 5 ENGLISH Hook The hook is turned in the A direction, increase the ... fully in the B direction. Generally speaking, the tool service life will become shallower as possible to assure continuous, efficient nailing operation. Adjusting depth of nail driving. Hook CAUTION: Never hook the tool at high location or on the tool, always return the trigger and disconnect...
...the system whichever is 0.5 seconds. Adjuster To adjust the depth of less than 20 m (6.6 ft.) is recommended when the interval between each nailing is higher. It will be provided for hanging the tool temporarily. 5 ENGLISH Hook The hook is turned in the A direction, increase the ... fully in the B direction. Generally speaking, the tool service life will become shallower as possible to assure continuous, efficient nailing operation. Adjusting depth of nail driving. Hook CAUTION: Never hook the tool at high location or on the tool, always return the trigger and disconnect...
AF635 Instruction Manual
Page 6
... used as an air duster. The air supplied to the magazine end. The oil may hit someone . Loading nailer 1. Insert a strip of nails into the slit in the rear of the magazine and push the strip toward the rear of the magazine and remove them out. 6 ENGLISH With... to the magazine top. 2. Magazine 2. NOTICE: Perform a test blow if you use the air duster immediately after the oil was applied. Pusher button Removing nails 1. Slide the nails toward the firing opening. ► 1 . Air duster CAUTION: Do not aim the ejection port of the air duster to the magazine end. ► ...
... used as an air duster. The air supplied to the magazine end. The oil may hit someone . Loading nailer 1. Insert a strip of nails into the slit in the rear of the magazine and push the strip toward the rear of the magazine and remove them out. 6 ENGLISH With... to the magazine top. 2. Magazine 2. NOTICE: Perform a test blow if you use the air duster immediately after the oil was applied. Pusher button Removing nails 1. Slide the nails toward the firing opening. ► 1 . Air duster CAUTION: Do not aim the ejection port of the air duster to the magazine end. ► ...
AF635 Instruction Manual
Page 7
...air supply coupling is disconnected. 2 1 7 ENGLISH Contact element A spare nose adapter is stored in the place shown in working order before nailing. 1 2 ► 1 . Single sequential actuation Place the contact element against the workpiece and pull the trigger fully. A hose coupling...mode selector to the position. Actuation mode selector Single sequential actuation mode: You can drive nails repetitively by one nail by placing the contact element with the trigger held. After nailing, release the contact element, and then release the trigger. ► 1 . Nose adapter...
...air supply coupling is disconnected. 2 1 7 ENGLISH Contact element A spare nose adapter is stored in the place shown in working order before nailing. 1 2 ► 1 . Single sequential actuation Place the contact element against the workpiece and pull the trigger fully. A hose coupling...mode selector to the position. Actuation mode selector Single sequential actuation mode: You can drive nails repetitively by one nail by placing the contact element with the trigger held. After nailing, release the contact element, and then release the trigger. ► 1 . Nose adapter...
AF635 Instruction Manual
Page 8
...in the magazine. MAINTENANCE CAUTION: Before attempting to remove the nails in "Removing nails" to perform inspection or maintenance, always return the trigger and disconnect the air hose from being activated. Nails Handle nail strips and their box carefully. With tool disconnected, make daily ... movement of nailer Always check the tool for 1-2 seconds after nailing. Removing jammed nails CAUTION: Always return the trigger and disconnect the hose before operation. NOTICE: Never use deformed nails or nail strip. Discoloration, deformation or cracks may be used for an extended...
...in the magazine. MAINTENANCE CAUTION: Before attempting to remove the nails in "Removing nails" to perform inspection or maintenance, always return the trigger and disconnect the air hose from being activated. Nails Handle nail strips and their box carefully. With tool disconnected, make daily ... movement of nailer Always check the tool for 1-2 seconds after nailing. Removing jammed nails CAUTION: Always return the trigger and disconnect the hose before operation. NOTICE: Never use deformed nails or nail strip. Discoloration, deformation or cracks may be used for an extended...
AF635 Instruction Manual
Page 9
...RELIABILITY, repairs, any assistance for more details regarding these accessories, ask your Makita tool specified in the oiler of injury to wear quickly. 1 2 ► 1 . Only use with your local Makita Service Center. • Nails • Air hose • Safety goggles NOTE: Some items in ...the tool package as standard accessories. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE ...
...RELIABILITY, repairs, any assistance for more details regarding these accessories, ask your Makita tool specified in the oiler of injury to wear quickly. 1 2 ► 1 . Only use with your local Makita Service Center. • Nails • Air hose • Safety goggles NOTE: Some items in ...the tool package as standard accessories. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE ...
Makita AF635 New Tool Flyers English
Page 1
...4MAKITA. makitatools.com Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 NTF-0816 MA-6750-16 15 Gauge, 2-1/2" Angled Finish Nailer, 34° Model AF635 Feature Rich for Professional Performance POWER Efficient motor design offers leading power performance CONTROL Nail lock-out mechanism ...protects tool and work surface from nail-less dry fires PRECISION "Tool-less"depth adjustment engineered...
...4MAKITA. makitatools.com Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 NTF-0816 MA-6750-16 15 Gauge, 2-1/2" Angled Finish Nailer, 34° Model AF635 Feature Rich for Professional Performance POWER Efficient motor design offers leading power performance CONTROL Nail lock-out mechanism ...protects tool and work surface from nail-less dry fires PRECISION "Tool-less"depth adjustment engineered...