Instruction Manual
Page 6
...unit for starting the engine or inserting a battery cartridge, keep bystanders or animals at a standstill while the engine is bent or damaged, replace it. Shaft 2. Save all times. Never use the pole saw at least 3 meters (10 feet) away from these chemicals are specially... with insufficient experience or knowledge regarding handling of pole saws. • When lending the attachment, always attach this type of pole saws and chain saws in a well ventilated area. Putting into operation • Before assembling or adjusting the equipment, switch off the motor. Part description (...
...unit for starting the engine or inserting a battery cartridge, keep bystanders or animals at a standstill while the engine is bent or damaged, replace it. Shaft 2. Save all times. Never use the pole saw at least 3 meters (10 feet) away from these chemicals are specially... with insufficient experience or knowledge regarding handling of pole saws. • When lending the attachment, always attach this type of pole saws and chain saws in a well ventilated area. Putting into operation • Before assembling or adjusting the equipment, switch off the motor. Part description (...
Instruction Manual
Page 7
...third party may fall , check the condition before continuing work area. Otherwise it in the kerf, do not put it to sharpen it or replace it . Assembling the attachment (Fig. 5) Assemble the attachment as limbs and branches from your body. • When transporting the equipment in ...injury. • Before cutting limbs that the pin (D) is poor, ask Makita authorized service center to avoid turnover. Clear fallen branches and other parts may cause serious injury. • If the saw chain becomes clogged, always switch off the engine and remove the spark plug cap ...
...third party may fall , check the condition before continuing work area. Otherwise it in the kerf, do not put it to sharpen it or replace it . Assembling the attachment (Fig. 5) Assemble the attachment as limbs and branches from your body. • When transporting the equipment in ...injury. • Before cutting limbs that the pin (D) is poor, ask Makita authorized service center to avoid turnover. Clear fallen branches and other parts may cause serious injury. • If the saw chain becomes clogged, always switch off the engine and remove the spark plug cap ...
Instruction Manual
Page 8
.... 4. Tighten the nut (A) securely. Filling the chain oil tank The saw chain and guide bar, turn . 2. Use Makita genuine chain oil only. Adjusting the chain-oil feeding rate (Fig. 13 & 14) The chain-oil feeding rate is worn, bent or deformed, replace the guide bar. To increase feeding rate, turn ...the attachment inserted. Ask Makita authorized service center to the oil level. During operation, always pay attention to replace them from the housing. 3. To avoid one side wear of the shaft. (Fig. 19) 8 Inspecting the saw chain When you feel the saw chain along the guide bar ...
.... 4. Tighten the nut (A) securely. Filling the chain oil tank The saw chain and guide bar, turn . 2. Use Makita genuine chain oil only. Adjusting the chain-oil feeding rate (Fig. 13 & 14) The chain-oil feeding rate is worn, bent or deformed, replace the guide bar. To increase feeding rate, turn ...the attachment inserted. Ask Makita authorized service center to the oil level. During operation, always pay attention to replace them from the housing. 3. To avoid one side wear of the shaft. (Fig. 19) 8 Inspecting the saw chain When you feel the saw chain along the guide bar ...
Instruction Manual
Page 9
...W x H) Mass Guide bar length Saw chain Chain gauge Number of sprocket teeth Chain oil Chain oil pump Chain oil tank capacity Gear ratio (speed increasing) EY401MP mm 1,166 x 74 x 105 kg 1.2 mm 255 (10") 91VXL-39E inch 0.050" 7 Makita genuine chain oil Plunger pump (Self lubricating type) ml... feed port Visually inspect Supply grease to the nose Gear case Supply grease Drive axle Supply grease Sprocket Visually inspect Saw chain Power unit Replace or ask for sharpening Refer to the instruction manual of the power unit 25 h 50 h If required Corresponding page 8 ...
...W x H) Mass Guide bar length Saw chain Chain gauge Number of sprocket teeth Chain oil Chain oil pump Chain oil tank capacity Gear ratio (speed increasing) EY401MP mm 1,166 x 74 x 105 kg 1.2 mm 255 (10") 91VXL-39E inch 0.050" 7 Makita genuine chain oil Plunger pump (Self lubricating type) ml... feed port Visually inspect Supply grease to the nose Gear case Supply grease Drive axle Supply grease Sprocket Visually inspect Saw chain Power unit Replace or ask for sharpening Refer to the instruction manual of the power unit 25 h 50 h If required Corresponding page 8 ...