Manual
Page 13
... unit forcefully. Not waiting for the unit to fall inside the equipment. • For environmental reasons, do not dispose of the equipment or expended supply waste at appropriate collection sites. • The inside of the machine becomes very hot. Touching a part with a "v" label (means hot surface)....other small metallic objects to cool down can take care that , install the new fusing unit. When installing the new fusing unit, turn off the printer and wait about 30 minutes. While moving the equipment, you move the equipment. R CAUTION: • Do not eat or swallow toner. ...
... unit forcefully. Not waiting for the unit to fall inside the equipment. • For environmental reasons, do not dispose of the equipment or expended supply waste at appropriate collection sites. • The inside of the machine becomes very hot. Touching a part with a "v" label (means hot surface)....other small metallic objects to cool down can take care that , install the new fusing unit. When installing the new fusing unit, turn off the printer and wait about 30 minutes. While moving the equipment, you move the equipment. R CAUTION: • Do not eat or swallow toner. ...
Manual
Page 159
... option. If it is installed properly, you will be formatted automatically. Note ❒ After finishing installation, you can check whether the Printer Hard Disk is not set properly. Note ❒ When installing other options on the controller board, do not close the controller board...the "List/Test Print" menu. Print the configuration page from step B. ing the supplied screw. ZHBP180E G Align the controller board to the steps for "Controller Option". ❒ If the Printer Hard Disk is turned on the controller board. If you cannot install it stops. ZHBP170E...
... option. If it is installed properly, you will be formatted automatically. Note ❒ After finishing installation, you can check whether the Printer Hard Disk is not set properly. Note ❒ When installing other options on the controller board, do not close the controller board...the "List/Test Print" menu. Print the configuration page from step B. ing the supplied screw. ZHBP180E G Align the controller board to the steps for "Controller Option". ❒ If the Printer Hard Disk is turned on the controller board. If you cannot install it stops. ZHBP170E...
Manual
Page 180
..., separate the IC2 lithium battery from the board, and then dispose of them according to the local regulations. ❖ Screw Note ❒ The other screw supplied is inside of the controller board compartment. B Turn off the power, and then un- Options User Account Enhance Unit Type B R WARNING: 1 • Do not place... The removed screws will explode and cause a burn. ❖ User Account Enhance Unit • The User Account Enhance Unit installed on the back of the printer.
..., separate the IC2 lithium battery from the board, and then dispose of them according to the local regulations. ❖ Screw Note ❒ The other screw supplied is inside of the controller board compartment. B Turn off the power, and then un- Options User Account Enhance Unit Type B R WARNING: 1 • Do not place... The removed screws will explode and cause a burn. ❖ User Account Enhance Unit • The User Account Enhance Unit installed on the back of the printer.
Manual
Page 181
... board to the controller board. Account Enhance Unit and the controller board, and then fasten the User Account Enhance Unit on the controller board using a 1 supplied screw. ZHBP020E The User Account Enhance Unit is not set properly. 39 ZHBP070E Important ❒ The...
... board to the controller board. Account Enhance Unit and the controller board, and then fasten the User Account Enhance Unit on the controller board using a 1 supplied screw. ZHBP020E The User Account Enhance Unit is not set properly. 39 ZHBP070E Important ❒ The...
Manual
Page 392
...the optional Printer Hard Disk. An error has occurred in the DIMM. Color Regist Error Energy Save Mode Hardware Problem Black PCU Hardware Problem Bypass Tray Hardware Problem Color PCU ...correctly. The printer is in the IEEE 1394 interface. An error has occurred in Energy Saver Mode. An error has occurred in the Bypass Tray. The color registration error ...in the Ethernet interface. Operating Instructions Administrator Reference 206 Getting Printer Information over the Network Printer current status You can check the printer's status using the telnet command. ❖ telnet Use ...
...the optional Printer Hard Disk. An error has occurred in the DIMM. Color Regist Error Energy Save Mode Hardware Problem Black PCU Hardware Problem Bypass Tray Hardware Problem Color PCU ...correctly. The printer is in the IEEE 1394 interface. An error has occurred in Energy Saver Mode. An error has occurred in the Bypass Tray. The color registration error ...in the Ethernet interface. Operating Instructions Administrator Reference 206 Getting Printer Information over the Network Printer current status You can check the printer's status using the telnet command. ❖ telnet Use ...
Manual
Page 431
...; Connectable number of devices in a bus: Maximum 63 ❖ Allowed cable hops in a bus: Maximum 16 ❖ Data Transmission: 400 Mbps (Maximum) ❖ Power supply: Non power supply Cable Power repeated (IEEE 1394a-2000 compliant) 802.11b Interface Unit TypeA (R-WL11) ❖ Transmission Spec.: Based on IEEE 802.11b (Wireless LAN) ❖...
...; Connectable number of devices in a bus: Maximum 63 ❖ Allowed cable hops in a bus: Maximum 16 ❖ Data Transmission: 400 Mbps (Maximum) ❖ Power supply: Non power supply Cable Power repeated (IEEE 1394a-2000 compliant) 802.11b Interface Unit TypeA (R-WL11) ❖ Transmission Spec.: Based on IEEE 802.11b (Wireless LAN) ❖...