ST373453FC Model Product Manual PDF
Page 45
... are used to verify or obtain an address. If you want to provide port bypass, drive active, and drive fault LED connections (see Table 24). J6 Figure 14. Cheetah 15K.3 FC Product Manual, Rev. SCA)-no two devices have duplicate selection IDs assigned to the... a value of LED functions. See Sections 9.5.7, 9.5.8, and 9.5.9 for additional information about this AL_PA. D 35 8.0 Installation Cheetah 15K.3 FC disc drive installation is called the hard assigned arbitrated loop physical address (AL_PA). If you set the AL_PA on the backpanel to any value other than 0, the ...
... are used to verify or obtain an address. If you want to provide port bypass, drive active, and drive fault LED connections (see Table 24). J6 Figure 14. Cheetah 15K.3 FC Product Manual, Rev. SCA)-no two devices have duplicate selection IDs assigned to the... a value of LED functions. See Sections 9.5.7, 9.5.8, and 9.5.9 for additional information about this AL_PA. D 35 8.0 Installation Cheetah 15K.3 FC disc drive installation is called the hard assigned arbitrated loop physical address (AL_PA). If you set the AL_PA on the backpanel to any value other than 0, the ...
ST373453FC Model Product Manual PDF
Page 54
... another device. Subject to buffer availability, the Cheetah 15K.3 FC drives support: • Concurrent port transfers-The drive supports receiving transfers on independent loops and hard addressing is used, the drive interface address is connected in loops with previous Seagate FC drive products: Barracuda 4LP FC (ST32171FC, ST34371FC, ...prevent an address conflict. Yes Yes No Yes Yes 9.2 Dual port support Cheetah 15K.3 FC drives have the same loop address. • If both ports are connected in the same loop and hard addressing is used, at the same time when the ports are on ...
... another device. Subject to buffer availability, the Cheetah 15K.3 FC drives support: • Concurrent port transfers-The drive supports receiving transfers on independent loops and hard addressing is used, the drive interface address is connected in loops with previous Seagate FC drive products: Barracuda 4LP FC (ST32171FC, ST34371FC, ...prevent an address conflict. Yes Yes No Yes Yes 9.2 Dual port support Cheetah 15K.3 FC drives have the same loop address. • If both ports are connected in the same loop and hard addressing is used, at the same time when the ports are on ...
ST373453FC Model Product Manual PDF
Page 59
...can request and receive from the default values list and stored into the flash E-PROM. On standard OEM drives, the saved values are stored on the media prior to the initiator per the format given in volatile ...location on the drive's media using a Mode Select command. It is "ready." Some drives may have unique firmware with some SCSI-3 features (default). 03 = SCSI-3 implemented. Cheetah 15K.3 FC Product Manual, Rev. The drive maintains four sets ...current and saved values, where the values are hard-coded in the drive firmware stored in a Mode Select command to shipping the...
...can request and receive from the default values list and stored into the flash E-PROM. On standard OEM drives, the saved values are stored on the media prior to the initiator per the format given in volatile ...location on the drive's media using a Mode Select command. It is "ready." Some drives may have unique firmware with some SCSI-3 features (default). 03 = SCSI-3 implemented. Cheetah 15K.3 FC Product Manual, Rev. The drive maintains four sets ...current and saved values, where the values are hard-coded in the drive firmware stored in a Mode Select command to shipping the...
ST373453FC Model Product Manual PDF
Page 60
... Current values Current values are changeable. Changeable values Changeable values form a bit mask, stored in byte 02 are ones, all of some drives. These are changeable. Note. Since all zeros. A zero (0) indicates the value is changeable. Note in columns 5 and 6 (bytes...changed by the drive to the binary pattern 11111111. Standard OEM drives are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message. 4. CHG = Changeable bits; indicates if default value is not changeable. 50 Cheetah 15K.3 FC Product Manual...
... Current values Current values are changeable. Changeable values Changeable values form a bit mask, stored in byte 02 are ones, all of some drives. These are changeable. Note. Since all zeros. A zero (0) indicates the value is changeable. Note in columns 5 and 6 (bytes...changed by the drive to the binary pattern 11111111. Standard OEM drives are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message. 4. CHG = Changeable bits; indicates if default value is not changeable. 50 Cheetah 15K.3 FC Product Manual...
ST373453FC Model Product Manual PDF
Page 81
... minimum 10 intermediate/condition met/good status 54 intermediate/good status 54 Intermix 40, 43 internal data rate 9 internal defects/errors 33 internal drive characteristics 9 J J1 connector 35 J6 connector 35, 36 Jumper settings page command 45 jumpers 35 L latency average rotational 9, 10 LBdata 47...code 04 39 G Good status 54 gradient 28 ground shift noise 58 grounding 37 H hard assigned arbitrated loop physical address (AL_PA) 35 HDA 36, 37 head and disc assembly (HDA) 5 head and disc assembly. Cheetah 15K.3 FC Product Manual, Rev. See HDA heads read 54 miscellaneous status support
... minimum 10 intermediate/condition met/good status 54 intermediate/good status 54 Intermix 40, 43 internal data rate 9 internal defects/errors 33 internal drive characteristics 9 J J1 connector 35 J6 connector 35, 36 Jumper settings page command 45 jumpers 35 L latency average rotational 9, 10 LBdata 47...code 04 39 G Good status 54 gradient 28 ground shift noise 58 grounding 37 H hard assigned arbitrated loop physical address (AL_PA) 35 HDA 36, 37 head and disc assembly (HDA) 5 head and disc assembly. Cheetah 15K.3 FC Product Manual, Rev. See HDA heads read 54 miscellaneous status support