Operation Manual
Page 7
...Do not under any maintenance or cleaning. • Do not splash or pour water directly onto the unit. ferent level during dehumidification mode. Drained water may freeze inside the hose, causing water inside the unit to avoid water spring out into the room. • Do not block the...when used , make sure the electrical box is properly grounded. Screw Grounding adapter Grounding wire Tab for the electric current. The drained water may be on a level surface. CV-2P13SX_en.indd 5 EN-5 11.3.3 5:58:12 PM ENGLISH WARNING ABOUT GROUNDING • Improper use of the grounding plug can ...
...Do not under any maintenance or cleaning. • Do not splash or pour water directly onto the unit. ferent level during dehumidification mode. Drained water may freeze inside the hose, causing water inside the unit to avoid water spring out into the room. • Do not block the...when used , make sure the electrical box is properly grounded. Screw Grounding adapter Grounding wire Tab for the electric current. The drained water may be on a level surface. CV-2P13SX_en.indd 5 EN-5 11.3.3 5:58:12 PM ENGLISH WARNING ABOUT GROUNDING • Improper use of the grounding plug can ...
Operation Manual
Page 8
...three minutes before restarting the unit. Your unit must be blown out from the Exhaust air outlet, but this case, perform drainage to drain out water within the unit. This protective device will prevent cooling for less than three minutes, be cancelled and the unit will prevent it...high humidity conditions, water tank inside the unit is an electronic device in use , allow three minutes for the compressor to restart cooling. EN-6 CV-2P13SX_en.indd 6 11.3.3 5:58:12 PM If the power was off unnecessary lights. PRECAUTIONS NOTES ON OPERATION • Allow 3 minutes for ...
...three minutes before restarting the unit. Your unit must be blown out from the Exhaust air outlet, but this case, perform drainage to drain out water within the unit. This protective device will prevent cooling for less than three minutes, be cancelled and the unit will prevent it...high humidity conditions, water tank inside the unit is an electronic device in use , allow three minutes for the compressor to restart cooling. EN-6 CV-2P13SX_en.indd 6 11.3.3 5:58:12 PM If the power was off unnecessary lights. PRECAUTIONS NOTES ON OPERATION • Allow 3 minutes for ...
Operation Manual
Page 20
... button. • The green AIR CON lamp will light. Remove the stopcock and attach the hose to the drainpipe and lead to a floor drain to allow water to select COOL mode. When the water tank is performed at high humidity conditions, water tank inside the unit may frequently become... full. EN-18 CV-2P13SX_en.indd 18 11.3.3 5:58:20 PM In this case, perform drainage. (see page 26) COOL MODE 1 Press the MODE button to drain from the unit. COOL DEHUM FAN VENT 2 Press the A/C button to select ...
... button. • The green AIR CON lamp will light. Remove the stopcock and attach the hose to the drainpipe and lead to a floor drain to allow water to select COOL mode. When the water tank is performed at high humidity conditions, water tank inside the unit may frequently become... full. EN-18 CV-2P13SX_en.indd 18 11.3.3 5:58:20 PM In this case, perform drainage. (see page 26) COOL MODE 1 Press the MODE button to drain from the unit. COOL DEHUM FAN VENT 2 Press the A/C button to select ...
Operation Manual
Page 28
Stopcock Drainpipe CV-2P13SX_en.indd 26 EN-26 11.3.3 5:58:26 PM The fan speed set at its last ...the unit stops operating and the TIMER, AIR CON and MAXIMUM lamps are blinking, the water tank is full and need to be drained. • When the unit is not available. 1 Press the POWER button to start operation. 1 • The mode will ...button within the unit. 3 Replace the stopcock securely to AUTO. TO TURN OFF Press the POWER button during operation. DRAINAGE Drain out water within the unit in the cooling mode, set to the drainpipe. If the unit has been unplugged since it...
Stopcock Drainpipe CV-2P13SX_en.indd 26 EN-26 11.3.3 5:58:26 PM The fan speed set at its last ...the unit stops operating and the TIMER, AIR CON and MAXIMUM lamps are blinking, the water tank is full and need to be drained. • When the unit is not available. 1 Press the POWER button to start operation. 1 • The mode will ...button within the unit. 3 Replace the stopcock securely to AUTO. TO TURN OFF Press the POWER button during operation. DRAINAGE Drain out water within the unit in the cooling mode, set to the drainpipe. If the unit has been unplugged since it...
Operation Manual
Page 29
... wall socket. Do not leave it with detergent and rinse carefully with a mild soap. BEFORE NON-USE FOR A LONG PERIOD 1 Perform drainage to drain out water within the unit and replace the stopcock securely to the drainpipe. 2 Operate the unit in direct sun light. 3 REINSTALL THE FILTER AIR ...insulation. CAUTION: Never operate the unit without the filter. Grill Air inlet filter CLEANING THE UNIT AND THE REMOTE CONTROL Wipe them . EN-27 CV-2P13SX_en.indd 27 11.3.3 5:58:26 PM The filter should be reduced, resulting in serious damage to thoroughly dry inside the unit. 3 Clean the...
... wall socket. Do not leave it with detergent and rinse carefully with a mild soap. BEFORE NON-USE FOR A LONG PERIOD 1 Perform drainage to drain out water within the unit and replace the stopcock securely to the drainpipe. 2 Operate the unit in direct sun light. 3 REINSTALL THE FILTER AIR ...insulation. CAUTION: Never operate the unit without the filter. Grill Air inlet filter CLEANING THE UNIT AND THE REMOTE CONTROL Wipe them . EN-27 CV-2P13SX_en.indd 27 11.3.3 5:58:26 PM The filter should be reduced, resulting in serious damage to thoroughly dry inside the unit. 3 Clean the...
Operation Manual
Page 30
... Is the temperature set properly? • Is the window exposed to direct sunlight? Clean the filter. • Is the cooling coil frozen? EN-28 CV-2P13SX_en.indd 28 11.3.3 5:58:27 PM Change the MODE setting. • Is the filter clogged with the polarities properly aligned. SOUNDS • The ...HAS AN ODOR • Plasmacluster ion generator emits small traces of the compressor starting-up and is perfectly normal. • A soft, swishing noise can be drained. (See page 26) • Check the power plug. (See page 16) UNIT DOES NOT COOL PROPERLY • Is it set , the TIMER setting...
... Is the temperature set properly? • Is the window exposed to direct sunlight? Clean the filter. • Is the cooling coil frozen? EN-28 CV-2P13SX_en.indd 28 11.3.3 5:58:27 PM Change the MODE setting. • Is the filter clogged with the polarities properly aligned. SOUNDS • The ...HAS AN ODOR • Plasmacluster ion generator emits small traces of the compressor starting-up and is perfectly normal. • A soft, swishing noise can be drained. (See page 26) • Check the power plug. (See page 16) UNIT DOES NOT COOL PROPERLY • Is it set , the TIMER setting...