Product Instruction Manual
Page 16
...in the occurrence and force of 3.8 cubic inches (62 cm³) and above - and must be equipped with certain cutting attachments, - To comply with the chain saw chain you use on "Low Kickback Saw Chain and Reduced Kickback Bars." 14 MS 201 C-M must be equipped with respect to kickback: - §... in the following referred to as a chain brake, low kickback saw . Some STIHL bar and saw chain types are designed to control the chain saw chain, reduced kickback bar, etc. STIHL recommends the use only the following standard apply with at least two devices to reduce...
...in the occurrence and force of 3.8 cubic inches (62 cm³) and above - and must be equipped with certain cutting attachments, - To comply with the chain saw chain you use on "Low Kickback Saw Chain and Reduced Kickback Bars." 14 MS 201 C-M must be equipped with respect to kickback: - §... in the following referred to as a chain brake, low kickback saw . Some STIHL bar and saw chain types are designed to control the chain saw chain, reduced kickback bar, etc. STIHL recommends the use only the following standard apply with at least two devices to reduce...
Product Instruction Manual
Page 18
...computer derived kickback angle of green marked or labeled chain saws under 3.8 cubic inches (62 cm³) displacement with green labeled bars and green labeled saw chains gives compliance with a STIHL Quickstop chain brake for both experienced and inexperienced chain saw chains. The matching of the chain... chain saw chain, this does not eliminate the risk of kickback injury. WARNING Use of other, non-listed bar / saw chain. 16 MS 201 C-M WARNING Reduced kickback bars and low kickback saw chains do not prevent kickback, but in combination with certain chain saws, comply with a ...
...computer derived kickback angle of green marked or labeled chain saws under 3.8 cubic inches (62 cm³) displacement with green labeled bars and green labeled saw chains gives compliance with a STIHL Quickstop chain brake for both experienced and inexperienced chain saw chains. The matching of the chain... chain saw chain, this does not eliminate the risk of kickback injury. WARNING Use of other, non-listed bar / saw chain. 16 MS 201 C-M WARNING Reduced kickback bars and low kickback saw chains do not prevent kickback, but in combination with certain chain saws, comply with a ...
Product Instruction Manual
Page 24
... of the chain saw directly behind the location of wood or plastic - N Do not cut where necessary to 5 cm) higher than center of the fall . The bumper spike rolls against the trunk. 22 MS 201 C-M N Cut horizontally towards the felling notch. English D =Felling Cut E = Hinge E D Felling Cut for Small Diameter Trees: Simple Fan...
... of the chain saw directly behind the location of wood or plastic - N Do not cut where necessary to 5 cm) higher than center of the fall . The bumper spike rolls against the trunk. 22 MS 201 C-M N Cut horizontally towards the felling notch. English D =Felling Cut E = Hinge E D Felling Cut for Small Diameter Trees: Simple Fan...
Product Instruction Manual
Page 53
... conforming with that requirement when used on "Safety Precautions and Working Techniques"): Rollomatic E guide bars Reduced kickback STIHL guide bars (with green label) Bar lengths: 30, 35, 40 cm (12, 14, 16 in.) Pitch: 3/8" P (9.32 mm) Groove width: 1.3 mm (0.050 in )... pump. Additional manual oil flow control Oil tank capacity: 7.4 fl.oz (0.22 l) Weight dry, without bar and chain MS 201 C-M: 8.6 lbs (3.9 kg) MS 201 C-EM with ErgoStart: 8.8 lbs (4.0 kg) Cutting Attachments English Recommended cutting attachments conforming with the 45 degree computed kickback angle requirement ...
... conforming with that requirement when used on "Safety Precautions and Working Techniques"): Rollomatic E guide bars Reduced kickback STIHL guide bars (with green label) Bar lengths: 30, 35, 40 cm (12, 14, 16 in.) Pitch: 3/8" P (9.32 mm) Groove width: 1.3 mm (0.050 in )... pump. Additional manual oil flow control Oil tank capacity: 7.4 fl.oz (0.22 l) Weight dry, without bar and chain MS 201 C-M: 8.6 lbs (3.9 kg) MS 201 C-EM with ErgoStart: 8.8 lbs (4.0 kg) Cutting Attachments English Recommended cutting attachments conforming with the 45 degree computed kickback angle requirement ...