Installation Instructions
Page 2
... made by grasping the plug, not the cord. • Always read and follow manufacturer's storage and ideal environment instructions for water, electrical power and grounding must contact a qualified electrical installer to installation instructions. If damage occurs, have it replaced with a properly...Water Supply Requirements 14 Door & Drawer Removal Bottom-Mount (Door 16 French Door Bottom-Mount (Door 17 Bottom-Mount (Drawer 19 Door & Drawer Reinstallation Bottom-Mount (Door 20 French Door Bottom-Mount (Door 21 Bottom-Mount (Drawer 22 Installation Connect to malfunction or leak...
... made by grasping the plug, not the cord. • Always read and follow manufacturer's storage and ideal environment instructions for water, electrical power and grounding must contact a qualified electrical installer to installation instructions. If damage occurs, have it replaced with a properly...Water Supply Requirements 14 Door & Drawer Removal Bottom-Mount (Door 16 French Door Bottom-Mount (Door 17 Bottom-Mount (Drawer 19 Door & Drawer Reinstallation Bottom-Mount (Door 20 French Door Bottom-Mount (Door 21 Bottom-Mount (Drawer 22 Installation Connect to malfunction or leak...
Installation Instructions
Page 13
... grille mounting clips with tubing clamp. NOTE: Complete any required panel installation and/or water supply connection before leveling. Connect tubing to frame with the lower cabinet slots. Correct leaks if necessary. 24 Leveling To protect property and refrigerator from damage, observe the following:...It may occur. 8 1 2 Pull on tubing to adjust the tilt of the unit, turn the leveler foot screw counterclockwise. Check for leaks and correct if necessary. 5 6 Slide brass nut over sleeve and screw nut into place. IMPORTANT: Do not overtighten. Cross threading may ...
... grille mounting clips with tubing clamp. NOTE: Complete any required panel installation and/or water supply connection before leveling. Connect tubing to frame with the lower cabinet slots. Correct leaks if necessary. 24 Leveling To protect property and refrigerator from damage, observe the following:...It may occur. 8 1 2 Pull on tubing to adjust the tilt of the unit, turn the leveler foot screw counterclockwise. Check for leaks and correct if necessary. 5 6 Slide brass nut over sleeve and screw nut into place. IMPORTANT: Do not overtighten. Cross threading may ...
Installation Instructions
Page 15
...the refrigerator section of purchase Date installed Dealer's name Address 29 All other servicing should be used in performing service on water connection. Model number Serial number Date of the unit. Record the following information indicated below. Do not repair or ...replace any part of the appliance unless specifically recommended in unit and verify operation. h Verify drain pan properly installed and no leaks on the appliance. h Remove internal packaging and labels and wipe unit down . • Verify dispenser operation (if applicable). Installer's information...
...the refrigerator section of purchase Date installed Dealer's name Address 29 All other servicing should be used in performing service on water connection. Model number Serial number Date of the unit. Record the following information indicated below. Do not repair or ...replace any part of the appliance unless specifically recommended in unit and verify operation. h Verify drain pan properly installed and no leaks on the appliance. h Remove internal packaging and labels and wipe unit down . • Verify dispenser operation (if applicable). Installer's information...
Use and Care Manual
Page 15
...valve (see Installation Instructions). • Plug the refrigerator back in and reset controls (see page 5). • Monitor water connection for 24 hours and correct leaks, if necessary. Hissing or popping • Compressor can make this noise while operating Gurgling or boiling sound Thumping Vibrating... for details on supply valve (see Installation Instructions). • Monitor water connection for 24 hours and correct leaks if necessary. • Run 10-15 glasses of these sounds seem even louder. Many of water from its front. • Be sure the refrigerator stays in an...
...valve (see Installation Instructions). • Plug the refrigerator back in and reset controls (see page 5). • Monitor water connection for 24 hours and correct leaks, if necessary. Hissing or popping • Compressor can make this noise while operating Gurgling or boiling sound Thumping Vibrating... for details on supply valve (see Installation Instructions). • Monitor water connection for 24 hours and correct leaks if necessary. • Run 10-15 glasses of these sounds seem even louder. Many of water from its front. • Be sure the refrigerator stays in an...
Use and Care Manual
Page 17
... The manufacturer recommends using copper tubing. Selfpiercing and 3/16" saddle valves cause low water pressure and may clog the line over time.* Turn off water supply and remove kinks. If kinks cannot be adjusted. ICE and WATER PROBLEM Refrigerator is leaking water Ice forms in inlet tube to ice maker POSSIBLE CAUSE Plastic tubing was...
... The manufacturer recommends using copper tubing. Selfpiercing and 3/16" saddle valves cause low water pressure and may clog the line over time.* Turn off water supply and remove kinks. If kinks cannot be adjusted. ICE and WATER PROBLEM Refrigerator is leaking water Ice forms in inlet tube to ice maker POSSIBLE CAUSE Plastic tubing was...