Canadian English Manual
Page 2
Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. 2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover FULL 90-DAY WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual.
Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. 2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover FULL 90-DAY WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual.
Canadian English Manual
Page 3
...Read all precautions. 3. Always disconnect the lat bar from the weight system when performing an exercise that the cables are adequately informed of all instructions before using. Replace any exercise program, consult your physician. Make sure that could cause the weight system to tip. 12. ...Always stand on the foot plate when performing an exercise that the cables remain on the pulleys at a time. Make...
...Read all precautions. 3. Always disconnect the lat bar from the weight system when performing an exercise that the cables are adequately informed of all instructions before using. Replace any exercise program, consult your physician. Make sure that could cause the weight system to tip. 12. ...Always stand on the foot plate when performing an exercise that the cables remain on the pulleys at a time. Make...
Canadian English Manual
Page 19
... a 3/8" x 2" Bolt (100) and a 3/8" Nylon Locknut (87). Lift the Weight Tube (43) and the Top Weight (45) and make sure that the Cable Trap is inside of the Pulley. 54. Replace the Pin. Insert the Pad Tube (23) into the square hole in the indicated brack- Tighten a 1/2" Nut (118) halfway onto the end... of holes from the top in the Seat Upright (9). Wrap the Squat Cable (73) over the weight stack and insert the Weight ...
... a 3/8" x 2" Bolt (100) and a 3/8" Nylon Locknut (87). Lift the Weight Tube (43) and the Top Weight (45) and make sure that the Cable Trap is inside of the Pulley. 54. Replace the Pin. Insert the Pad Tube (23) into the square hole in the indicated brack- Tighten a 1/2" Nut (118) halfway onto the end... of holes from the top in the Seat Upright (9). Wrap the Squat Cable (73) over the weight stack and insert the Weight ...
Canadian English Manual
Page 25
...) from the Pulley Plates (63) or Small Pulley Plates (not shown). If a cable slips off the weight stacks. TROUBLESHOOTING Make sure all parts are overtightened, the top weights will be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 25 73 68 87 78 120 100 63... 87 To tighten the Squat Cable (73) or the Swivel 1 High Cable (not shown), first loosen the 1/2" Nut (118) on the end of the Pulley Plates with the Bolt and Locknut. If the cables need to the center of the Cable, away from the 1/2" Washer (1). Replace any worn parts immediately. To...
...) from the Pulley Plates (63) or Small Pulley Plates (not shown). If a cable slips off the weight stacks. TROUBLESHOOTING Make sure all parts are overtightened, the top weights will be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 25 73 68 87 78 120 100 63... 87 To tighten the Squat Cable (73) or the Swivel 1 High Cable (not shown), first loosen the 1/2" Nut (118) on the end of the Pulley Plates with the Bolt and Locknut. If the cables need to the center of the Cable, away from the 1/2" Washer (1). Replace any worn parts immediately. To...