Owner's Manual
Page 3
...of cables is a fire and electrical shock hazard. • Should this unit, on vacation, EMX3000-Owner's Manual Precautions s Warnings • Do not place a container with a damaged power cord is a fire and electrical shock hazard. • Do not scratch, bend, twist, pull... you notice any abnormality, such as inside of the power cord. Fire or electrical shock may result. • Connect this unit's power cord only to an AC outlet of the type stated in a safe place for purchasing the Yamaha EMX3000 Powered Mixer. In particular, be damaged, turn it from the ...
...of cables is a fire and electrical shock hazard. • Should this unit, on vacation, EMX3000-Owner's Manual Precautions s Warnings • Do not place a container with a damaged power cord is a fire and electrical shock hazard. • Do not scratch, bend, twist, pull... you notice any abnormality, such as inside of the power cord. Fire or electrical shock may result. • Connect this unit's power cord only to an AC outlet of the type stated in a safe place for purchasing the Yamaha EMX3000 Powered Mixer. In particular, be damaged, turn it from the ...
Owner's Manual
Page 4
... can be applied to add reverberation or ambience to vocals or instrumental sounds. ✦The EMX3000 has implemented "EEEngine", Yamaha's epochal amp drive technology to create an unrivaled high-efficiency drive. The mixer also has ample power, with a maximum output of applications from installed systems to small-scale PA systems. ✦A two...
... can be applied to add reverberation or ambience to vocals or instrumental sounds. ✦The EMX3000 has implemented "EEEngine", Yamaha's epochal amp drive technology to create an unrivaled high-efficiency drive. The mixer also has ample power, with a maximum output of applications from installed systems to small-scale PA systems. ✦A two...
Owner's Manual
Page 9
... to monitor the level of the signal output from the ST 1 jacks. The final level of these knobs adjust the input sensitivity of the power amp (the input level that is a mix of this control does not affect signals that is a mix of the STEREO bus is adjusted by the... output from the BRIDGE jack. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to adjust the knob. EMX3000-Owner's Manual The sensitivity range is on / off for the MIC input jacks for channels 1~8. When this position when you connect only...
... to monitor the level of the signal output from the ST 1 jacks. The final level of these knobs adjust the input sensitivity of the power amp (the input level that is a mix of this control does not affect signals that is a mix of the STEREO bus is adjusted by the... output from the BRIDGE jack. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to adjust the knob. EMX3000-Owner's Manual The sensitivity range is on / off for the MIC input jacks for channels 1~8. When this position when you connect only...
Owner's Manual
Page 11
...connected. THe nominal output level is +4 dB. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can use a foot switch. Note: Use only the L phone (A) jacks to connect ...output level at the ST 1 jacks, and use a "Y" cable to connect to a monitor system. EMX3000-Owner's Manual Note: Use only the L jack to connect a monaural output device. 5 TAPE jacks These...stage-monitoring amplifiers or powered speakers here. The signal adjusted by the EFFECT fader (control panel G), and output from these jacks. Connect an external mixer output here. A EFFECT jack...
...connected. THe nominal output level is +4 dB. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can use a foot switch. Note: Use only the L phone (A) jacks to connect ...output level at the ST 1 jacks, and use a "Y" cable to connect to a monitor system. EMX3000-Owner's Manual Note: Use only the L jack to connect a monaural output device. 5 TAPE jacks These...stage-monitoring amplifiers or powered speakers here. The signal adjusted by the EFFECT fader (control panel G), and output from these jacks. Connect an external mixer output here. A EFFECT jack...
Owner's Manual
Page 21
... dB is referenced to 0.775 Vrms, 0 dBV is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4) C-R/PHONES ...775 mV) +20 dB (7.75 V) 3 mW 100 mW +4 dB (1.23 V) +20 dB (7.75 V) 300 W/4Ω 600 W/8Ω PHONO JACK PHONE JACK (I /O)4 POWER AMP IN (L, R) +4 dB (1.23 V)5 +18 dB (6.16 V)5 PHONE JACK3 1. Impedance balaned. (T=HOT, R=COLD, S=GND) 2. Input specifications 17 s Input speci...
... dB is referenced to 0.775 Vrms, 0 dBV is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4) C-R/PHONES ...775 mV) +20 dB (7.75 V) 3 mW 100 mW +4 dB (1.23 V) +20 dB (7.75 V) 300 W/4Ω 600 W/8Ω PHONO JACK PHONE JACK (I /O)4 POWER AMP IN (L, R) +4 dB (1.23 V)5 +18 dB (6.16 V)5 PHONE JACK3 1. Impedance balaned. (T=HOT, R=COLD, S=GND) 2. Input specifications 17 s Input speci...