Owner's Manual
Page 9
... l / h on the front panel (or the input selector buttons on the remote control). Notes • When you connect headphones, no signals are output at the SUBWOOFER OUTPUT jack or at the SPEAKERS terminals. • All Dolby Digital and DTS audio signals are output directly from their respective speakers without effect processing...
... l / h on the front panel (or the input selector buttons on the remote control). Notes • When you connect headphones, no signals are output at the SUBWOOFER OUTPUT jack or at the SPEAKERS terminals. • All Dolby Digital and DTS audio signals are output directly from their respective speakers without effect processing...
Owner's Manual
Page 13
... page 18 for connection information. 6 DIGITAL INPUT jacks See pages 14 and 15 for connection information. 7 Audio component jacks See page 17 for connection information. 8 SUBWOOFER OUTPUT jack See page 12 for connection information. 9 SPEAKERS terminals See page 11 for connection information. (U.S.A. INTRODUCTION Rear panel 1 2 3 4 5 CONTROLS AND FUNCTIONS XM MULTI CH...
... page 18 for connection information. 6 DIGITAL INPUT jacks See pages 14 and 15 for connection information. 7 Audio component jacks See page 17 for connection information. 8 SUBWOOFER OUTPUT jack See page 12 for connection information. 9 SPEAKERS terminals See page 11 for connection information. (U.S.A. INTRODUCTION Rear panel 1 2 3 4 5 CONTROLS AND FUNCTIONS XM MULTI CH...
Owner's Manual
Page 14
... ITU-R* speaker setting. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 ft) above the floor. ■ Subwoofer (SW) The use of the LFE (lowfrequency effect) channel included in Dolby Digital and DTS software. If for high fidelity reproduction of...the full system. Turn it is the radio communication sector of the room to the monitor as possible, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from the ideal listening position. But it slightly toward the center of...
... ITU-R* speaker setting. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 ft) above the floor. ■ Subwoofer (SW) The use of the LFE (lowfrequency effect) channel included in Dolby Digital and DTS software. If for high fidelity reproduction of...the full system. Turn it is the radio communication sector of the room to the monitor as possible, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from the ideal listening position. But it slightly toward the center of...
Owner's Manual
Page 16
model) 6 Subwoofer 3 Center speaker 1 2 Right Left Front speakers (B) ■ FRONT terminals Connect one front speaker system, connect it to the FRONT A terminals. ■ CENTER terminals Connect a center ... ANT GND FM ANT SPEAKERS CLASS 2 WIRING B FRONT CENTER R L A R FRONT L IMPEDANCE SELECTOR (U.S.A. If you use only one or two speaker systems (1, 2) to these terminals. ■ SUBWOOFER OUTPUT jack Connect a subwoofer with built-in amplifier (6) (such as the YAMAHA Active Servo Processing Subwoofer System) to these terminals.
model) 6 Subwoofer 3 Center speaker 1 2 Right Left Front speakers (B) ■ FRONT terminals Connect one front speaker system, connect it to the FRONT A terminals. ■ CENTER terminals Connect a center ... ANT GND FM ANT SPEAKERS CLASS 2 WIRING B FRONT CENTER R L A R FRONT L IMPEDANCE SELECTOR (U.S.A. If you use only one or two speaker systems (1, 2) to these terminals. ■ SUBWOOFER OUTPUT jack Connect a subwoofer with built-in amplifier (6) (such as the YAMAHA Active Servo Processing Subwoofer System) to these terminals.
Owner's Manual
Page 20
... MULTI CH INPUT jacks to the MULTI CH INPUT jacks This unit is equipped with 6 additional input jacks (FRONT L/R, CENTER, SURROUND L/R and SUBWOOFER) for discrete multi-channel input from the front left and right input jacks for missing speakers. Be sure to match the left and right output... AUDIO R L VIDE DVD SURROUND DIGITAL INPUT SUB DVD 3 WOOFER CENTER DTV/ CBL V-AUX COAXIAL CD IN RL RL Center out Surround out Subwoofer out Front out Multi-format player or external decoder Notes • When you select the component connected to the MULTI CH INPUT jacks as the...
... MULTI CH INPUT jacks to the MULTI CH INPUT jacks This unit is equipped with 6 additional input jacks (FRONT L/R, CENTER, SURROUND L/R and SUBWOOFER) for discrete multi-channel input from the front left and right input jacks for missing speakers. Be sure to match the left and right output... AUDIO R L VIDE DVD SURROUND DIGITAL INPUT SUB DVD 3 WOOFER CENTER DTV/ CBL V-AUX COAXIAL CD IN RL RL Center out Surround out Subwoofer out Front out Multi-format player or external decoder Notes • When you select the component connected to the MULTI CH INPUT jacks as the...
Owner's Manual
Page 24
... (7.9 x 5.8 m, 45 m2) [Other models] S (small) 3.6 x 2.8 m, 10 m2 M (medium) 4.8 x 4.0 m, 20 m2 L (large) 6.3 x 5.0 m, 30 m2 5 Press d to enter "SUBWOOFER" and then press j / i to enter "BASIC MENU". - PRESET/CH "ROOM" appears in the front panel display. ENTER + A-E/CAT. PRESET/CH Choices: YES, NONE • Select... "YES" if you have a subwoofer in your system. - If the front panel display shows anything other than "BASIC MENU", press SET MENU repeatedly until "BASIC MENU...
... (7.9 x 5.8 m, 45 m2) [Other models] S (small) 3.6 x 2.8 m, 10 m2 M (medium) 4.8 x 4.0 m, 20 m2 L (large) 6.3 x 5.0 m, 30 m2 5 Press d to enter "SUBWOOFER" and then press j / i to enter "BASIC MENU". - PRESET/CH "ROOM" appears in the front panel display. ENTER + A-E/CAT. PRESET/CH Choices: YES, NONE • Select... "YES" if you have a subwoofer in your system. - If the front panel display shows anything other than "BASIC MENU", press SET MENU repeatedly until "BASIC MENU...
Owner's Manual
Page 26
... value. - ENTER + A-E/CAT. ENTER + A-E/CAT. Press i to adjust the balance. PRESET/CH 22 Press j to adjust the balance between the front left speaker and the subwoofer. 14 To confirm the settings, press d / u repeatedly until the menu disappears. - PRESET/CH 15 Press d repeatedly until "2 SP LEVEL" appears in the front panel display...
... value. - ENTER + A-E/CAT. ENTER + A-E/CAT. Press i to adjust the balance. PRESET/CH 22 Press j to adjust the balance between the front left speaker and the subwoofer. 14 To confirm the settings, press d / u repeatedly until the menu disappears. - PRESET/CH 15 Press d repeatedly until "2 SP LEVEL" appears in the front panel display...
Owner's Manual
Page 30
... You can adjust the default input mode of input signals you can adjust the output level of input jacks. This is detected. - R" to adjust the subwoofer output level. Note When "INPUT MODE" is set "INPUT MODE" to "DTS". • Depending on the player, DTS decoding may not be sure ... source. Selects only analog signals. PRESET/CH The control range is set menu is from +10 dB to -10 dB for the front speakers and subwoofer. AMP LEVEL TITLE BAND • Select "FRONT L" to adjust the front left speaker output level. • Select "SWFR" to adjust the surround right...
... You can adjust the default input mode of input signals you can adjust the output level of input jacks. This is detected. - R" to adjust the subwoofer output level. Note When "INPUT MODE" is set "INPUT MODE" to "DTS". • Depending on the player, DTS decoding may not be sure ... source. Selects only analog signals. PRESET/CH The control range is set menu is from +10 dB to -10 dB for the front speakers and subwoofer. AMP LEVEL TITLE BAND • Select "FRONT L" to adjust the front left speaker output level. • Select "SWFR" to adjust the surround right...
Owner's Manual
Page 31
... to adjust the surround right speaker output level. • Select "TEST SUR.L" to adjust the surround left speaker output level. • Select "TEST SUBWOOFER" to adjust. - ENTER + A-E/CAT. PRESET/CH The control range is from +10 dB to -10 dB for the center and surround speakers,...levels so that the volume from your listening position. AMP TEST RETURN MEMORY 2 Press u / d repeatedly to select a speaker to adjust the subwoofer output level. PLAYBACK Notes • You cannot use TEST to adjust speaker levels, the speaker levels you previously adjust during playback will also change...
... to adjust the surround right speaker output level. • Select "TEST SUR.L" to adjust the surround left speaker output level. • Select "TEST SUBWOOFER" to adjust. - ENTER + A-E/CAT. PRESET/CH The control range is from +10 dB to -10 dB for the center and surround speakers,...levels so that the volume from your listening position. AMP TEST RETURN MEMORY 2 Press u / d repeatedly to select a speaker to adjust the subwoofer output level. PLAYBACK Notes • You cannot use TEST to adjust speaker levels, the speaker levels you previously adjust during playback will also change...
Owner's Manual
Page 37
... DTS) are input, they are downmixed to 2 channels and output from the front left and right speakers. 1 Press AMP on . "BASS" is set to the subwoofer in the following cases: - SOUND FIELD PROGRAMS ■ Using Virtual CINEMA DSP Virtual CINEMA DSP allows you select a CINEMA DSP program (see page 54) in...
... DTS) are input, they are downmixed to 2 channels and output from the front left and right speakers. 1 Press AMP on . "BASS" is set to the subwoofer in the following cases: - SOUND FIELD PROGRAMS ■ Using Virtual CINEMA DSP Virtual CINEMA DSP allows you select a CINEMA DSP program (see page 54) in...
Owner's Manual
Page 58
...distance of the front speaker. • Select "CENTER" to adjust the distance of the center speaker. • Select "SURR" to the subwoofer. The LFE channel carries low-frequency special effects which are output from the main listening position. The low-frequency signals of the "1B FRONT"... setting. • Select "BOTH" if you connected a subwoofer. However, this is effective only when this unit decodes Dolby Digital or DTS signals. Thus, a certain amount of the surround channel are directed...
...distance of the front speaker. • Select "CENTER" to adjust the distance of the center speaker. • Select "SURR" to the subwoofer. The LFE channel carries low-frequency special effects which are output from the main listening position. The low-frequency signals of the "1B FRONT"... setting. • Select "BOTH" if you connected a subwoofer. However, this is effective only when this unit decodes Dolby Digital or DTS signals. Thus, a certain amount of the surround channel are directed...
Owner's Manual
Page 65
.... "BASS" in "SPEAKER SET" is being played. The source does not contain lowfrequency bass signals. Check that the impedance selector setting is heard from the subwoofer. Turn on . Set "BASS" to "NONE". The protection circuitry has been activated because of the HiFi DSP programs (except for Try another sound field program...
.... "BASS" in "SPEAKER SET" is being played. The source does not contain lowfrequency bass signals. Check that the impedance selector setting is heard from the subwoofer. Turn on . Set "BASS" to "NONE". The protection circuitry has been activated because of the HiFi DSP programs (except for Try another sound field program...
Owner's Manual
Page 70
... Logic II Dolby Pro Logic II is an improved technique used in many TV and cable broadcasts as well. Dolby Surround is widely used as a subwoofer, for bass effects, called the sampling frequency, while the degree of fineness when converting the sound level into this channel is determined by the 5 full...
... Logic II Dolby Pro Logic II is an improved technique used in many TV and cable broadcasts as well. Dolby Surround is widely used as a subwoofer, for bass effects, called the sampling frequency, while the degree of fineness when converting the sound level into this channel is determined by the 5 full...
Owner's Manual
Page 72
... Impedance CD, etc 200 mV/47 kΩ MULTI CH INPUT 200 mV/47 kΩ • Output Level/Output Impedance AUDIO OUT (REC 200 mV/1.2 kΩ SUBWOOFER OUTPUT 4 V/1.2 kΩ VIDEO SECTION • Video Signal Type [U.S.A., Canada, Korea and General models NTSC [Other models PAL • Component Signal Level 1 Vp-p/75 Ω •...
... Impedance CD, etc 200 mV/47 kΩ MULTI CH INPUT 200 mV/47 kΩ • Output Level/Output Impedance AUDIO OUT (REC 200 mV/1.2 kΩ SUBWOOFER OUTPUT 4 V/1.2 kΩ VIDEO SECTION • Video Signal Type [U.S.A., Canada, Korea and General models NTSC [Other models PAL • Component Signal Level 1 Vp-p/75 Ω •...