Home » Audiovox » Remote Controls » Audiovox APS687

Audiovox APS687 Support Question

Find answers below for this question about Audiovox APS687 - Car Prestige Remote Start.
Need a Audiovox APS687 manual? We have 1 online manual for this item!

Audiovox Overview Questions Manuals Reviews Videos Research

Question posted by Johnkapalka35 on June 1st, 2022

Longer Run Time

Who do I make the run time longer

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on June 1st, 2022 7:25 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,673,770

1,100
points

Selectable Steady or Flashing Parking Lights for Run Indication ... Your code hopping transmitters will change their signal every time the button is pressed

https://www.voxxelectronics.com/docs/common/APS687A/APS687A_OM.pdf

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Audiovox APS687 Manual Pages

Installation Manual - Page 1

...can either be indicated if a feature is indicated. Press and release valet switch 3 times; Be certain to RF feature program mode. Press and hold valet switch for a particular model. Siren and or... lights chirp/flash 2 times indicating access to place a check mark indicating the method used in the box located on ...

Installation Manual - Page 2

...Unlock 3 chirps = 1 sec. Action Turn ignition on Press and release the valet switch 3 times Within 3 seconds, turn ignition Off Then On This Action Accesses Feature Bank 2 Alarm First Press and release the valet switch... 1 time Press transmitter Lock button to change Press transmitter Lock button to change Press ...

Installation Manual - Page 3

... the program mode as follows: Turn the ignition on . RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 1st Defrost Output Pulsed 10 Mins 2nd RF Start Chirp Off On On & Car Finder 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins 4th Parking Lights On Steady Flashing 5th...

Installation Manual - Page 4

...then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features Press the valet switch one time Press transmitter Lock button to change or Press and release ... Mins 2 chirps = RF start chirp on 1 chirp = RF start chirp off 2 chirps = run time set for 10 mins 3 chirps = run time set fro 15 mins 4 chirps = run time set for 20 mins 1 chirp = run time set for diesel engine 20 ...

Installation Manual - Page 5

..." of the ignition switch wiring harness to allow the hood to depress the switch at a time, through the panel from the front side and pressing on , this unit allows routing from water...or screws as the module or wiring may be made for overriding the remote start is issued. In these vehicles, route the antenna toward the control module using a 7/ 16" nut driver or deep well socket. Choose...

Installation Manual - Page 6

... CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS. Verification: These wires will remain...Neutral Start Switch will allow you will crank the car when the RF signal is required for the start ...remote start unit and assure that the vehicle cannot start input for glow plug pre-heat which will realize why the connection of the installing technician to start via RF control...

Installation Manual - Page 7

... show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions and will show 0 volts when the key is turned to the ignition ...Output Connect this wire to allow output during the "START" mode. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key...

Installation Manual - Page 8

... to be connected to a separate, (Other than the wire Red or Red/White is used. Fuses must switch to ), constant on or off during the start cycle. (See feature bank 3 selection # 8) Connect this wire harness. RED/BLACK Wire: + 12 Volts Input Note: The Red/Black and Pink are dry contacts and...

Installation Manual - Page 9

...wires through the firewall into the engine compartment. It is applied to the Brown wire, the Remote Starter will be connected to use the Brown w/ Black wire; If the brake light switch ... of 20 GRAY w/ BLACK TRACER WIRE: Negative Inhibit Input 2 Any time the gray w/ black tracer wire is grounded, the Remote Starter will stop operating, even if the signal is received from the ...

Installation Manual - Page 10

... to the vehicle's parking light wire. Pass Output NOTE: You must disconnect the ignition input of the alarm from the running under control of the remote start and keep the vehicle's engine running under the control of 25 Amp. In all of the White wires to a fused (15A max.) +12 volt battery source, and connect the...

Installation Manual - Page 11

...to terminal #87a of cylinders. NOTE: The above information and following diagram is under the control of the Remote Start Unit. If the vehicle has a single coil unit for each cylinder, it may be...later in later model Cadillacs, they are run through the firewall into the engine compartment and connect to the negative side of thin gauge wires running from one cylinder for the GM VATS system...

Installation Manual - Page 12

...) This output is operational under control of the Remote Start unit's operation. NOTE: The outputs above are low current outputs and must go to + 12 then to ground to allow the control of the remote start unit shuts down. This will occur regardless of 20 When the unit is selected for one time read transponders circuits. 12...

Installation Manual - Page 13

... via an independent RF channel from the keychain transmitter. This is running under the control of trunk release circuits, some remote start trigger inputs, will occur as dictated by the same transmitter button ... of the remote start function. Connect the dark blue wire to terminal 86 of this trunk release output, or press and release the trunk/key button two times within 2 seconds...

Installation Manual - Page 14

...Interior Illumination circuit is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar device. TIMED START PROGRAM: The Remote Start unit has the ability to a fused + 12 ... current circuits, will start the vehicle. Black w/ White Trace Wire: 300 mA Horn Output The black w/ white trace wire is firmly seated making good contact to the control unit. Connect relay...

Installation Manual - Page 15

... the start every 2 or 4 hours as follows. 1 Flash 5, 10, 15, or 20, minute run timer expired. 2 Flashes Low or No tach signal received. 3 Flashes Positive input shut down. 4 Flashes Control switch ... volts with the ignition in the on the last remote start 2 times. (Press the trunk/key button four times). The Remote Car Starter will chirp 4 times. Turn the ignition key to a +12 volt ...

Installation Manual - Page 16

...on, off . Block the drive wheels to remove the key. 7. Reach inside the car and pull the hood release. 3. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL... , on the brake pedal and shift the gear selector into the R/S Override mode indicating that the remote start from being activated while a mechanic or vehicle owner is the responsibility of operation. TESTING YOUR INSTALLATION: ...

Installation Manual - Page 17

... Park / Neutral ECM input: 1. 8. To connect the Audiovox remote start , failing this reference wire. 3. If the unit attempts to start unit to this test, recheck your Yellow Wire's connection. The information concerning the Mechanical Neutral Safety Switch provided below ), indicates the slight reconfiguration of the control switch wiring and the addition of the Neutral...

Installation Manual - Page 18

...-7827 18 of the Remote Start, the vehicle will allow the safety required for method 2: A. Cut this wire and connect the ignition cylinder side to the key in step D. D. H. The anode (Non Striped) side must be certain to chassis ground. If the hood pin switch is running under the control of 20 Cut this...

Installation Manual - Page 19

... connect the ignition cylinder side to distinguish the Remote Start control switch from all activated features and safety systems ...Make sure to the hood pin switch. This will not inhibit any of the controls of the Remote Start Unit. Replace all the safety features of the Audiovox Remote Start unit and tested all panels that connects the chime module to the Alarm/Remote Start's control...