Benelli Legacy Support Question
Benelli Legacy Support Question
Find answers below for this question about Benelli Legacy.Need a Benelli Legacy manual? We have 1 online manual for this item!
Question posted by Dalea51 on September 28th, 2020
Removal Of Magazine Tube
what tool do I use to remove the magazine tube with. There is something rattling around inside the tub
Current Answers
Answer #1: Posted by Troubleshooter101 on September 28th, 2020 11:31 PM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,050
Member since:
September 30th, 2015 Points: 2,927,050
Unable to get the name of the tool because over the web their is no discussion about it.
Please check this video tutorial
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Benelli Legacy Manual Pages
User Manual - Page 17
RAFFAELLO cal. 12 RAFFAELLO cal. 20
BLACK EAGLE COMPETITION
LEGACY EXECUTIVE AQUILA DEL DUCA
OWNER'S MANUAL
Data subject to modification without notice
17 GB
User Manual - Page 18
...sure of your target and the back stop beyond the reach of children. 13) Avoid the use or with unloaded firearm, lock the bolt to
the rear and check the barrel of alcoholic beverages... unless
the action is not damaged in any way. 8) Before firing, with which you intend to use of your firearm.
BE CAREFUL WITH YOUR FIREARM - WARNING:
DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING...
User Manual - Page 19
... Spring pressure is fully compressed, it overcomes breech block inertia, thrusting it from the magazine tube to shoot. GB
Upon shooting, the hammer spring forces
the cartridge drop lever upwards...a special
cartridge drop lever, the outer portion of
which , pulled by cartridges of our guns.
ge it to the extent that the shotguns can be considered the most important, ingenious ...
User Manual - Page 20
...gun) The shotgun is packed for shipping in three parts (fig. 1): - otherwise the hammer is ready to fully cycle the action. is not responsible for any case, shells that the barrel ring slides over the tubular magazine...in (fig. 2).
2) Take the stock-receiver-cover-bolt unit with the right hand, using the cocking lever, bring the bolt into place and is firmly seated. Benelli Armi S.p.A. The...
User Manual - Page 21
... locking of the screwdriver.
2) Using a 13 mm deep well socket and along with a rachet and extension, remove the stock retaining nut by turning... The kit, which will now all slide off the recoil spring tube.
4) Now you .
For other and must be properly reinserted...of
the Benelli shotgun. Note that the chamber and the magazine of metal stock locking plate set plus plastic drop change ...
User Manual - Page 22
...). The recoil pad may now be used only with left -hand shotgun to assure...left -hand (cast-on the recoil spring tube and re-tighten it.
Turn the shotgun ...D
63,5 ± 1
Coupling instruction: the drop change . 22
5) Place your dimensions and style of the gun as well.
DROP CHANGE SCHEDULE
Stock locking plate (steel)
Reference
letter
R.H. To ensure a correct drop, always match...
User Manual - Page 23
...special ejection window (fig. 18) and release the cocking lever to open the bolt (fig. 15).
for use. Open the bolt and hold it is two, three, four or five rounds, including the one , two...forward, allowing the bolt to precision machined tolerances on the trigger guard until the magazine is extracted and ejected from the gun (fig. 19). To load the shotgun:
- Make sure that the weapon ...
User Manual - Page 24
...30).
10) Remove the locking head pin from the bolt (fig. 31).
11) Remove the bolt locking head from the bolt (fig. 32).
12) Remove the inertia spring from its guides (fig. 28).
8) Remove the firing pin ...24. When unloading the chamber always point the gun in safe direction and insert the safety catch on your Benelli make sure that the chamber and the magazine of your left with the point of the...
User Manual - Page 25
... outlined under the section "Assembly of Packaged Gun" page 20.
Do not
25
use fingers only.
9) Hold the stock-receiver assembly...reassemble the bolt group according the procedure shown in fig. 46.
use tools to block the firing pin (fig. 45). Make sure that...receiver from
the locking head face (fig. 49) until it is completely inside (fig. 40).
4) Place the bolt recoil spring in its seat on ...
User Manual - Page 26
...tubes
The barrels with internal chokes are equipped with dust or foreign matter. All barrels are internally chromium plated. The following few rounds, check that the chamber and the magazine of your shotgun are unloaded! (Carefully read the instructions on gun...securely fastened to keep the gun in good order, we re- commend you to the receiver. Note: always use . - Remove this by the recoil ...
User Manual - Page 27
...and 36 grammes for 20 gauge. All Benelli shotguns are necessary to use ammunition that the choke wrench has been removed from the barrel muzzle.
4) Complete the choke assembly tighten it strenghtly... choke tube desired, having care to insert the non-threaded part inside the barrel before to fire any of the ammunition listed above types of ammunition, 76 mm (3") cartridges may be used with ...
Similar Questions
Raffaello 123 Magazine
How do you get the end off the end off the magazine to replace the springs?
How do you get the end off the end off the magazine to replace the springs?
(Posted by kuntryboyrr 8 years ago)
Benelli Ultralight 20 Guage Semi Auto Only Cycles 2 Of The 3 Cartridges.
Capacity is 2 in magazine and 1 in chamber. When firing only 1 cartridge cycles from the magazine. T...
Capacity is 2 in magazine and 1 in chamber. When firing only 1 cartridge cycles from the magazine. T...
(Posted by jakehayrynen 10 years ago)