Bosch 1199VSR Support Question
Bosch 1199VSR Support Question
Find answers below for this question about Bosch 1199VSR - NA VSR 1/2" Dual Torque Hammer Drill.Need a Bosch 1199VSR manual? We have 1 online manual for this item!
Question posted by davebelcher on July 9th, 2022
Troubleshooting Bosch 1199vsr
I have a Bosch 1199VSR that isn't working. I have opened it up and checked continuity at all points and it appears to be getting power all the way through. Possibly be in need of new brushes??
Current Answers
Answer #1: Posted by SonuKumar on July 9th, 2022 11:43 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,673,770
Member since:
May 9th, 2021 Points: 16,673,770
https://www.youtube.com/watch?v=AnxZyJNuTr8
https://www.youtube.com/watch?v=AnxZyJNuTr8&t=424
https://www.manualslib.com/manual/19369/Bosch-1199vsr.html?page=10#manual
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Bosch 1199VSR Manual Pages
Operating Instructions - Page 2
... power tool. When operating a power tool outside, use tool while tired or under the influence of electric shock. Do not use an outdoor extension cord marked "W-A" or "W." Use safety equipment. Check ... gases, or dust. Do not abuse the cord.
Water entering a power tool will further enhance your work area clean and well lit.
Remove adjusting keys or wrenches before plugging...
Operating Instructions - Page 3
.... Develop a periodic maintenance schedule for maximum control over torque reaction or kick-back.
Always wear safety goggles or eye protection when using this manual. Accidental start-ups could result in , check that may create a risk of electric shock or injury.
Check for Hammer Drills
Hold tool by hammer-drill action may result in the hands of untrained users...
Operating Instructions - Page 4
...tool avoid contact with approved safety equipment, such as the drill bit is rotating. Do not grasp the tool or place your hands too close to switch it "OFF", by power sanding, sawing,
grinding, drilling... type of work , the reaction torque of
these exposures...drill before the bit is locked "ON" during the use, be difficult. Accessories may be ready for a strong reaction torque. Check...
Operating Instructions - Page 5
... speed, orbits etc. Selector settings I, II, III,
Speed, torque or position settings.
This symbol designates that this tool is listed to Canadian Standards by Underwriters Laboratories. Proper interpretation of the... be used on your tool. n0 .../min
No load speed
Rotational speed, at no load
Revolutions or reciprocation per second)
W
Watt
Power
kg
Kilograms
Weight
min
Minutes...
Operating Instructions - Page 6
...the tool accidentally.
Hammer Drill
FIG. 1
DRILL/HAMMER DRILL SELECTION DIAL
REVERSING SWITCH LEVER
COLLAR MOUNT CHUCK
RUBBERIZED GRIP
TRIGGER
DEPTH GAUGE
HAND GRIP
DEPTH GAUGE RELEASE BUTTON
"LOCK-ON" BUTTON
GEAR CHANGE SELECTION DIAL
CHUCK KEY & STORAGE AREA
Model number No load speed 1 No load speed 2 Maximum capacities Chuck capacity Material Concrete Aluminum Steel
1199VSR
n0...
Operating Instructions - Page 7
... allows for various jobs. FIG. 3
DRILL/HAMMER DRILL SELECTION DIAL The selector dial allows the tool to the speed and torque required for continuous operation at a complete standstill. REVERSING SWITCH LEVER This tool is directly related to be controlled from minimum to the trigger. This results in longer tool life
while maximizing power in both forward and reverse directions...
Operating Instructions - Page 8
... both tool and bit. The technique is hard, drill the entire length. For large bits, insert the bit as far as the screw runs down. Too much pressure at low speed will eliminate the need for hard materials. Set the screw snugly by sliding over the surface. If it will do neater work before...
Operating Instructions - Page 9
... masonry work . Use of the wire come in such a way that secures the bonnet is not exceeded by slowing the drill to the tool. Operate the brush with the lightest pressure so only the tips of the "Lock-ON" button feature will find the "Lock-ON" button feature a convenience for the continuous operation required for drilling in...
Operating Instructions - Page 10
...To maintain peak efficiency of power or
overheating.
Wire Sizes in mm2
Cord Length in A.W.G. WARNING
Preventive maintenance performed by inserting pointed objects through openings.
! CARBON BRUSHES The brushes and commutator in Meters 15...ready to avoid overheating or motor failure.
TOOL LUBRICATION Your Bosch tool has been properly lubricated and is necessary...
Similar Questions
I Need Help With Troubleshooting A Problem With My Bosch Dishwasher
Our dishwasher no longer cleans our dishes. Water will not shoot out of the arms or spouts. How do I...
Our dishwasher no longer cleans our dishes. Water will not shoot out of the arms or spouts. How do I...
(Posted by egaardermiller 7 years ago)
How To Replace The Cord On 1199 Vsr Drill
Cord is damaged and I need instructions on the best way to replace it
Cord is damaged and I need instructions on the best way to replace it
(Posted by Dougje1 9 years ago)
She42l15uc Bosch Troubleshooting
The dishes don't seem to be drying. The sanitized light is not illuminating after the wash. Regular ...
The dishes don't seem to be drying. The sanitized light is not illuminating after the wash. Regular ...
(Posted by Dougpstone 10 years ago)
Chuck Key Size For 1199vsr Drill?
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
(Posted by aguada2000 13 years ago)