Bosch PS40-2 Support Question
Bosch PS40-2 Support Question
Find answers below for this question about Bosch PS40-2 - 10.8V 1/4" Hex Cordless Impact Driver.Need a Bosch PS40-2 manual? We have 1 online manual for this item!
Question posted by coca on September 22nd, 2011
Psr 18 Cordless Drill Manual
The person who posted this question about this Bosch product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Bosch PS40-2 Manual Pages
Operating Instructions - Page 2
...tool or
battery-operated (cordless) power tool.
When operating a power tool outdoors, use an extension cord suitable for outdoor use the cord for the connection of the power tool in serious personal injury. While the tool...fumes. BM 2610958960 06-08 6/10/08 1:47 PM Page 2
General Safety Rules
!
Failure to lose control.
Do not operate power tools in explosive atmospheres, such as...
Operating Instructions - Page 3
...burns. Use clamps or other small metal objects that have the power tool repaired before inserting battery pack. Use battery tools only with water. Under abusive conditions, liquid may be careful not...off . BM 2610958960 06-08 6/10/08 1:47 PM Page 3
Keep handles dry, clean and free from the battery, avoid contact. Use the correct power tool for misalignment or binding of moving ...
Operating Instructions - Page 4
... driving long screws - Some examples of work by power sanding, sawing,
grinding, drilling and other
reproductive harm. Never hold it at your legs. Remove battery pack before... when using the tool for extended periods.
The clutch can cause hearing loss.
BM 2610958960 06-08 6/10/08 1:47 PM Page 4
Safety Rules for Cordless Impact Drivers
Hold tools by taking frequent rest...
Operating Instructions - Page 5
...10/08 1:47 PM Page 5
Battery/Charger
Before using battery charger, read all instructions and cautionary markings on flat non-flammable surfaces and away from metal objects. Use only Bosch approved chargers with your product or direct replacement as listed in tool...minimum of the case are not in the catalog or this manual. If liquid comes in locations where temperatures will not exceed ...
Operating Instructions - Page 6
...battery, the battery must be
illegal in the United States or Canada. BM 2610958960 06-08 6/10/08 1:47 PM Page 6
Battery Disposal
!
The
RBRC program provides a convenient
alterative
to a ...Service Center for information on the lithium-ion (Li-ion) battery indicates Robert Bosch Tool Corporation is part of our commitment to disassemble the battery or
remove any component projecting ...
Operating Instructions - Page 7
...
Type or a characteristic of current
Alternating or direct current
Type or a characteristic of drill bits, grinding wheels, etc.
BM 2610958960 06-08 6/10/08 1:47 PM Page 7
Symbols
IMPORTANT: Some of these symbols will allow you to operate the tool better and safer. Please study them and learn their meaning. Symbol Name
Designation...
Operating Instructions - Page 8
...the tool accidentally.
Cordless Impact Driver
FIG. 1
BUILT IN WORK LIGHT
VENTILATION OPENINGS
LOCKING SLEEVE
FORWARD/REVERSING BUTTON & TRIGGER LOCK
VARIABLE SPEED TRIGGER SWITCH
BATTERY RELEASE TABS
BATTERY PACK
Model number Voltage rating No load speed Charge time Impact rate Maximum torque
Maximum Capacities Chuck size
Screw Sizes
Battery pack
Charger Voltage rating
PS40 10.8V/12V...
Operating Instructions - Page 9
... bit after shut-off has been reached can cause the tool to twist out of rotation until the clutch again reaches shut-off clutches are not designed for locking the trigger in "OFF" position to the far left. The Bosch model PS40-2 Cordless Impact Driver has a collet that accepts only standard 1/4" hexagonal shank accessories with...
Operating Instructions - Page 10
...properly:
d. See "Tools, Electric" in these operating instructions or those supplied with your local Bosch Service Center. BM 2610958960 06-08 6/10/08 1:47 PM Page 10
BUILT IN WORK LIGHT Your tool is also equipped ... or the battery pack is fully charged and is too hot or cold for better visibility when drilling/driving (Fig. 1).
Clean with a light that the battery pack is too hot or too ...
Operating Instructions - Page 11
...-drilling is to start slowly, increasing the speed as the screw runs down.
The best method to determine the right impacting... screw snugly by sliding over the surface. Always hold the tool firmly and exert light, steady pressure.
FIG. 5
BATTERY PACK...impacting/tightening duration can be reached in less time if the battery pack was not completely discharged. BM 2610958960 06-08 6/10...
Operating Instructions - Page 12
...your tool without stripping, splitting or separating the material.
Screw
FIG. 6
-12- The torque build-up depends on the duration of the impacting/tightening action. First, clamp the pieces together and drill the...SCREWS
2. The maximum torque is not followed, the tool will have a tendency to torque or twist in (Fig. 6) will enable you to 10 Sec. Soft case: The joining of the screw....
Operating Instructions - Page 13
... specially designed for use 3-wire
extension cords that have 3-prong plugs and
receptacles. Cleaning
! The tool may result in Meters 25 50 100 150 15 30 60 120
3-6 6-8 8-10 10-12 12-16
18 16 16 14 18 16 14 12 18 16 14 12 16 16 14 12 14 12 - -
0.75 0.75 1.5 2.5 0.75 1.0 2.5 4.0 0.75 1.0 2.5 4.0 1.0 2.5 4.0 - --- -
-13...
Similar Questions
Drill Bit Wobbles
My Hammer drill works but the bit wobbles, it is off center. how can i fix it?
My Hammer drill works but the bit wobbles, it is off center. how can i fix it?
(Posted by hj518 7 years ago)
Where Can I Find Manual To Disamble And Repair
(Posted by Anonymous-132064 10 years ago)
Does Anyone Out There Have A Manual For The Bosch 1581avs Jig Saw?
(Posted by bargeboard 11 years ago)
Won't Hammer, My 11241 Evs Will Drill But Won't Hammer At All
(Posted by gpw4653 12 years ago)
Chuck Key Size For 1199vsr Drill?
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
What is the correct size of chuck key for the 1199VSR drill, I purchased a 1/2 "X1/4 pilot, ans a 1/...
(Posted by aguada2000 13 years ago)