Carvin 1584 Support Question
Carvin 1584 Support Question
Find answers below for this question about Carvin 1584.Need a Carvin 1584 manual? We have 1 online manual for this item!
Question posted by adnanzubair25 on January 26th, 2022
Carvin 1584 Crossover Issue
I got a pair of CARVIN 1584,one speaker crossover network has an issue that the midrange gives reduced sound while its mid and high frequency is given by tweeter and some times both are not giving any sound only woofer sounds,What could be the reason?
Current Answers
Answer #1: Posted by SonuKumar on January 27th, 2022 8:17 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,623,780
Member since:
May 9th, 2021 Points: 16,623,780
https://carvinaudio.com/pages/crossover-schematics
How do you know if your crossover is bad?
Play music, check for A/C voltage between the output (tweet or mid) on the crossover. If voltage is 0, then you know its dead.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Carvin 1584 Manual Pages
Instruction Manual - Page 1
... future. Front loaded woofers and wide dispersion titanium high frequency drivers are covered for the rest of your unit, always use , moisture or dust. The power generated by the APS internal power amps has the capacity to your records. Write this number on manufacturer's defects. Carvin's APS™ Active Powered Speakers are not liable for...
Instruction Manual - Page 2
... than 0.1% @ 90% power Total Power : 350 watts RMS Low Frequency: 300 watts @ 8Ω Mid Frequency: N/A High Frequency: 50 watts @ 16Ω
Sensitivity: 1.5VAC for full output-level set at "0" Equalization: High ±6dB @ 10 kHz
Mid ±6dB, sweepable 100 Hz-5 kHz Low ±6dB @100 Hz Active Crossover Filters: 24dB / octave Linkwitz-Riley Input/Through: 1/4" balanced & XLR...
Instruction Manual - Page 3
...
1-800-854-2235 Electronic Crossover www.carvin.com
INTERNAL FUSE 90-250 VAC
10 VA ~50-60HZ
GND LIFT
CHANNEL ONE
HIGH PHASE
MID PHASE
MONO [ LOW 1+2 ]
LOW PHASE
STEREO BIAMPING
Right Input
SWITCHABLE TO MONO [ LOW 1+2]
CHANNEL TWO
HIGH PHASE
MID PHASE
LOW PHASE
Right High Out
Left Low Out
Right Low Out
SPEAKER - 1
+ --BRIDGE-- +
- PROFESSIONAL STEREO...
Instruction Manual - Page 4
... active.
3. POWER Push this problem, the APS utilizes time delay circuits to the unit. CROSSOVER FREQUENCY SWITCH The CROSSOVER FREQUENCY switch selects the crossover point for it's respective driver. APS BI-AMP/TRI-AMP REAR PANEL:
2
LOW
0
-3
+3
MID
0
-3
+3
3
MID SWEEP 1kHz
HIGH
0
-3
+3
-6 +6 EQ IN -6 +6
100Hz 5kHz
-6 +6
742A
TIME-ALIGNED BI-AMP SYSTEM 300 W RMS
0 LEVEL...
Similar Questions
Powered Sub Not Working
sun was working and shut off fuse is good and I am getting 124v to the board
sun was working and shut off fuse is good and I am getting 124v to the board
(Posted by Louis35900 10 months ago)
Power Supply
where can I get a power supply for one of these speakers
where can I get a power supply for one of these speakers
(Posted by Louis35900 10 months ago)
1542 Carvin Speakers.
Looking for replacement parts for 1542 Carvin 80 ohms 400 watt speakers,
Looking for replacement parts for 1542 Carvin 80 ohms 400 watt speakers,
(Posted by jerardatchinsen 6 years ago)
Crossovers
Where can I get replacement croosovers for the 1542 Carvin floor wedge stage monitors?
Where can I get replacement croosovers for the 1542 Carvin floor wedge stage monitors?
(Posted by coopthecableguy 7 years ago)
Speaker Output Connection Won't Work
Hi,3 out of 4 of the speaker output will not work. The #2 output will work. Any idea as to what I am...
Hi,3 out of 4 of the speaker output will not work. The #2 output will work. Any idea as to what I am...
(Posted by drmjschmid 7 years ago)