Dell PowerConnect 6224 Support Question
Dell PowerConnect 6224 Support Question
Find answers below for this question about Dell PowerConnect 6224.Need a Dell PowerConnect 6224 manual? We have 5 online manuals for this item!
Question posted by thielkechura19 on February 9th, 2014
How To Upgrade Firmware On Dell Powerconnect 6224
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by MWatDell on February 9th, 2014 10:35 PM
MWatDell
Member since:
November 17th, 2011 Points: 306,490
Member since:
November 17th, 2011 Points: 306,490
Hi thielkechura19
To upgrade the firmware on Dell PowerConnect 6224, please refer to the manuals from the download zip file.
You can refer to PC6200UpgradeSoftwareFromVersion2.xProcedure and PC6200UpgradeSoftwareFromVersion 3.x.x.xProcedure.
Hope this helps.
MW@Dell
Related Dell PowerConnect 6224 Manual Pages
User's Guide - Page 5
... XFP Module Port LEDs 65 10/100/1000 Base-T Port LEDs 65 System LEDs 67 Stacking LEDs 68
5 Configuring Dell PowerConnect
Overview 71 Starting the CLI 72 General Configuration Information 74
Terminal Connection Configuration 74 Baud Rate 74 Other Configuration Requirements 74 Booting the Switch 75 Configuration Overview 81 Easy Setup Wizard 81
5
User's Guide - Page 19
...The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for a multi-layer switch, including layer 2
switching, IPv4 routing, IPv6 routing, IP multicast, quality of service, security, and system management features. • High availability with the firmware available on the Dell Support website, support.dell.com. The topics covered in this product. The Dell...
User's Guide - Page 52
... to Console
52
Cable and Port Information Figure 3-4. Serial Connection to Switch
Serial Connector to the terminal (console) ASCII DTE RS-232. 2. Figure 3-3. Connecting the Switch to the serial port of the Master switch. Bay 1 and Bay 2 Interfaces
The Dell™ PowerConnect™ 6200series switches support dual 10 Gb slot interfaces. If you are configuring a stack...
User's Guide - Page 71
... up for this section.
You can download the release notes from the Dell Support website at support.dell.com/manuals. Performing other procedures. 5
Configuring Dell PowerConnect
Overview
This chapter describes the initial switch configuration. If you connect the terminal to a subordinate switch, you are installing a stack of installation and configuration procedures illustrated in...
User's Guide - Page 72
....
72
Configuring Dell PowerConnect You can be defined. However, to access the switch through Telnet, at least one user account must have a defined IP address, corresponding management access granted, and a workstation connected to the switch before using the Easy Setup Wizard and enter the necessary commands to complete the required tasks.
3.
The switch can access...
User's Guide - Page 73
...)
Reboot
No
Loading program from flash to RAM
Yes Enter Wizard
No
Initial Configuration: IP Address, Subnetmask, Users Basic Security configuration
Wizard Configuration Process
Standard Switch Installation
Advanced Configuration: IP Address from DHCP, IP Address from bootp, Security management
Advanced Switch Installation
Configuring Dell PowerConnect
73
User's Guide - Page 74
... fits into its network environment. Other Configuration Requirements The following is required for switch remote control use with Telnet, SSH, and so forth
74
Configuring Dell PowerConnect
Terminal Connection Configuration Your switch requires the following terminal connection parameters for configuration: • no parity • one stop bit • 8 data bits • no flow control...
User's Guide - Page 75
Turn on the terminal and indicate test success or failure. Start operational code. 2 - Booting the Switch
When the power is an example of simultaneously open files: 22
Configuring Dell PowerConnect
75 Select an option. If no selection in 10 seconds then
operational code will start.
1 - The following text is turned on mount:
NOT ENABLED...
User's Guide - Page 77
... - Abort boot code update 7 - Items such as addresses, versions, and dates may differ for each switch. If no problems were encountered during boot. Select (1, 2):2
Boot Menu Version: 3.2.0.1
Options available 1 -... product data 6 - Operational Code Date: Tue May 26 14:12:20 2009
Configuring Dell PowerConnect
77 Update boot code 8 - Delete backup image 9 - The auto-boot message that...
User's Guide - Page 80
...version, download and install the latest version. See "Software Download and Reboot."
80
Configuring Dell PowerConnect Applying Interface configuration, please wait ... console> After the switch boots successfully, a prompt appears and you can use the local terminal to select management ...: as rawFs, device = 0x20001 Formatting...OK.
(Unit 1 -
Waiting to begin configuring the switch.
User's Guide - Page 81
....
The initial turn-up . You may enter the system to make the switch manageable.
If the network is setup for configuring the default route
There are two ...switch.
This administrative account setup by the wizard has the highest privilege level (level 15). The wizard sets up without a configuration or with only the default factory configuration. Configuring Dell PowerConnect...
User's Guide - Page 82
...switch. Although spaces are given another opportunity to run the set-up wizard. Once saved, the wizard option is not used by the SNMP manager at a given IP address. Functional Flow
The following functional flow diagram illustrates the procedures for the Easy Setup Wizard.
82
Configuring Dell PowerConnect...only presented again if you reset the switch to the factory-default settings. The wizard...
User's Guide - Page 84
...can skip the setup wizard, and enter CLI mode to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you enter with no options defined, the...community string to run the setup wizard within 60 seconds)? [Y/N] y
Step 1:
84
Configuring Dell PowerConnect Would you like to be used by the following example contains the sequence of an Easy ...
User's Guide - Page 85
... admin
Please enter the user password: ********
Please reenter the user password: ********
Step 3:
Configuring Dell PowerConnect
85 The system is used .
{public}:
public
Please enter the IP address of the Management ...:
Please enter the SNMP community string to be used to login to access the switch. For more information on setting up user accounts and changing privilege levels, see the...
User's Guide - Page 93
Configuring Dell PowerConnect
93
NOTE: In the Web browser enable SSL 2.0 or greater for the page content ...ip https authentication local NOTE: You should generate a new crypto certificate each time you upgrade (install a new version of) the control software application on the switch.
console#configure console(config)#crypto certificate 1 generate console(config-crypto-cert)#country US console...
Getting Started Guide - Page 7
... of self-adhesive rubber pads for the latest updates on documentation and firmware. The switch is adequate front and rear clearance for cabling,
power connections, and ventilation. • Cabling - Installation
This document provides basic information to install, configure, and operate Dell™ PowerConnect™ PC6224, PC6248, PC6224P, PC6248P, and PC6224F systems. For more information...
Release Notes - Page 1
...and Celeron is a trademark of Microsoft Corporation. Microsoft and Windows are registered trademarks of Intel Corporation; Dell™ PowerConnect™ 6224/6224F/6224P/6248/6248P
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Date: May 2010 System Firmware Version 3.2.0.6
Information in this document is subject to change without prior written permission is prohibited, except...
Release Notes - Page 3
... improvements to update the boot code AND firmware.
NOTE: The PC6200 switches when stacked require that this release note be installed on every switch member. System Firmware Version 3.2.0.6
Page 1 You MUST follow the procedure set forth in the Dell PowerConnect 6200 Series Release 3.2 Upgrade Procedure included in your switch becoming inoperable.
It is recommended that the...
Release Notes - Page 4
... and the Dell™ PowerConnect™ 6200 Series Configuration Guide. Denotes a scheduled maintenance release of the product software. Hardware Supported
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6 NOTE: OMNM 4.1 will not discover the switches running firmware version 2.x or earlier.
Firmware Image Name...
Release Notes - Page 25
...in Interface Config Mode to set the number of the command to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds. Default: Not...Disabled by default.
System Firmware Version 3.2.0.6
Page 23 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating...
Similar Questions
How To Upgrade Firmware Switch Dell Powerconnect 5548
(Posted by Jordmoa 9 years ago)
How To Upgrade Dell Powerconnect 6200 Firmware
(Posted by jfb0black 10 years ago)