Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by annjeLcvk on August 20th, 2013
How To Configure Igmp Snooping On Dell Powerconnect 6248
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
Command Line Interface Guide - Page 56
... displays IPv6 Snooping Querier information.
IGMP Snooping Querier Configures IGMP Snooping Querier and displays IGMP Snooping Querier information.
Dynamic ARP Inspection Configures for rejection of invalid and malicious ARP packets. LLDP
Configures and displays LLDP information. IP Addressing
Configures and manages IP addresses on the switch. Link Dependency
Configures and displays...
Command Line Interface Guide - Page 332
... of this command to disable IGMP snooping globally.
Syntax ip igmp snooping no form of this command. Syntax ip igmp snooping no ip igmp snooping
Default Configuration IGMP snooping is not enabled on an Ethernet interface, use the no ip igmp snooping
332
IGMP Snooping Commands console(config)# ip igmp snooping
ip igmp snooping (interface)
Use the ip igmp snooping command in Global...
Command Line Interface Guide - Page 333
Example The following example enables IGMP snooping. Default Configuration IGMP snooping is 260 seconds.
To reset to configure the host-time-out. Command Mode Interface Configuration (Ethernet, port-channel) mode
IGMP Snooping Commands
333
Host timeout in Interface Configuration mode to the default host time-out, use the no ip igmp snooping host-time-out • time-out - If an...
Command Line Interface Guide - Page 339
... allows the switch to immediately remove the layer 2 LAN interface from its forwarding table entry upon receiving an IGMP leave message for that group. Syntax ip igmp snooping fast-leave vlan-id no user guidelines. This setting prevents the inadvertent dropping of this command disables IGMP Snooping fast-leave mode on VLANs by default. Default Configuration IGMP snooping is...
Command Line Interface Guide - Page 346
..., the IPv4 address is the global querier address. If a VLAN has IGMP Snooping Querier enabled, and IGMP Snooping is operationally disabled on the VLAN. IGMP Snooping querier functionality is re-enabled if IGMP Snooping is disabled by default.
Default Configuration IGMP snooping querier is operational on it, IGMP Snooping Querier functionality is the querier address for the source address...
Command Line Interface Guide - Page 351
... state. Indicates the IP address of the most recent Querier from which a Query was received.
• Last Querier Version - Default Configuration
This command has no default configuration
IGMP Snooping Querier Commands
351 If the Snooping Switch is used, the command shows the global information and the information for vlan_id, the following information appears:
• VLAN Admin...
User's Guide - Page 19
... PoE capability. The Dell PowerConnect 6248P adds support for power-over-Ethernet (PoE) capability. The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. The Dell™ PowerConnect™ 6200 series are provided with hot swappable stack members. 1
Introduction
This section describes the switch user-configurable features.
User's Guide - Page 402
...
Use the VLAN Querier page to specify the IGMP Snooping Querier settings for this feature.
Configuring IGMP Snooping Querier Settings with CLI Commands
For information about the CLI commands that the snooping switch is going to send periodically.
Table 7-43.
Sets the IGMP Querier timer expiration period.
Enables the Snooping Querier to participate in the Querier Election process...
User's Guide - Page 404
...following fields: • VLAN ID - VLAN Querier Summary Table
Configuring VLAN Querier Settings with CLI Commands See "Configuring IGMP Snooping Querier Settings with CLI Commands" on the VLAN.
404
Configuring Switching Information Figure 7-83. VLAN Querier Status Use the VLAN Querier Status page to view the IGMP Snooping Querier settings for individual VLANs. Identifies the VLAN. • VLAN...
User's Guide - Page 405
... VLAN Querier Status with CLI Commands
See "Configuring IGMP Snooping Querier Settings with a time interval equal to non-querier state. When this mode is the Querier in periodic IGMP queries sent on page 402. The Snooping Querier transitions to non-querier state.
• Snooping Querier VLAN Address - The Snooping switch is disabled, upon seeing another querier of the...
User's Guide - Page 414
...;MLD Snooping → VLAN Querier Status in the tree view. Shows whether the MLD Snooping Querier is enabled or disabled on page 402. Identifies the VLAN. • VLAN Mode -
Figure 7-91. VLAN Querier Summary Table
Configuring VLAN Querier Settings with CLI Commands See "Configuring IGMP Snooping Querier Settings with CLI Commands" on the VLAN.
414
Configuring Switching Information...
Getting Started Guide - Page 7
... that the following site requirements: • Power - The switch is routed to avoid sources of electrical noise such as radio transmitters, broadcast
amplifiers, power lines, and fluorescent lighting fixtures. • Ambient - Installation
This document provides basic information to install, configure, and operate Dell™ PowerConnect™ PC6224, PC6248, PC6224P, PC6248P, and PC6224F...
Release Notes - Page 4
... version number. Hardware Supported
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6 Firmware Downgrade
Downgrading from 3.2.0.6 to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide and the Dell™ PowerConnect™ 6200 Series Configuration Guide. Supported Firmware Functionality...
Release Notes - Page 7
...information between neighboring devices (routers, bridges, access servers, and switches). System Firmware Version 3.2.0.6
Page 5
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ MLD Snooping (RFC2710)
In IPv4, Layer 2 switches can use IGMP Snooping to limit the flooding of multicast traffic by dynamically configuring Layer 2 interfaces so that multicast traffic is forwarded to...
Release Notes - Page 25
...configuration of the command to set the number of seconds that it is supported.
Default: The switch remains in the quiet state for details. Default: Disabled by default.
PowerConnect 6224/6224F/6224P/6248...The hold-count keyword is used to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds. Refer to configure a port on a CX-4 or stacking ...
Configuration Guide - Page 9
... system and port settings, use system interfaces and utilities, and create and use the Dell™PowerConnect™ 6200 Series switch in a mixed IPv6/IPv4 network.
• "Quality of Service" on page 139 provides configuration scenarios for class-of how to configure IGMP, IGMP proxy, Distance Vector Multicast Routing Protocol (DVMRP), and Protocol Independent Multicast (PIM) on...
Configuration Guide - Page 42
... 1/g5
100 0100.5E01.0102
Dynamic 1/g10
Forbidden ports for group 225.1.1.1. Without IGMP snooping, all multicast groups, which would be flooded with traffic for group 225.1.1.2.
Total Packets Received Without Errors.......... 626494
Unicast Packets Received 0
42
Switching Configuration View information about the multicast data transmitted or received by each interface. Host B sends...
Configuration Guide - Page 43
...commands to use as the IGMP querier so that it can perform the IGMP snooping functions on the VLAN.
The IGMP snooping feature listens to these IGMP reports to operate. console(config)#ip igmp snooping
console(config)#ip igmp snooping querier
console(config)#ip igmp snooping querier address 10.10.20.12 NOTE: The IGMP snooping feature must configure another switch as the source address when...
Configuration Guide - Page 44
...#show ip igmp snooping querier
Global IGMP Snooping querier status
IGMP Snooping Querier Mode Enable
Querier Address 10.10.10.33
IGMP Version 2
Querier Query Interval 100
Querier Expiry Interval 100
Example #4: Enable IGMP Snooping Querier on a VLAN To configure IGMP Snooping Querier on the switch. The first ip igmp snooping command in this example enables the IGMP snooping querier on...
Configuration Guide - Page 150
When to Enable IP Multicast on the PowerConnect 6200 Series Switch
Use the IP multicast feature on the PowerConnect 6200 Series switch to route multicast traffic between VLANs. For more information, see "IGMP Snooping" on a PowerConnect 6200 Series switch in IPv4 networks. They use IGMP snooping to those sections for configuration instructions.
150
Multicast IPv6 multicast routers use ...
Similar Questions
How To Enter Configuration Mode On Powerconnect 5448 Switch
(Posted by C133pic 9 years ago)
How To Configure Bootpdhcprelay Dell Powerconnect 6248
(Posted by ekJNI 9 years ago)
How To Save Configuration On Dell Powerconnect 6248 Switch
(Posted by vgjayzi 10 years ago)
How To Save Configuration On Dell Powerconnect 6248
(Posted by Chrgo 10 years ago)