Dell PowerEdge 2950 Support Question
Dell PowerEdge 2950 Support Question
Find answers below for this question about Dell PowerEdge 2950.Need a Dell PowerEdge 2950 manual? We have 8 online manuals for this item!
Question posted by gypspoc on November 16th, 2013
Poweredge 1900 Romb Batt How To Change
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerEdge 2950 Manual Pages
Installing a SATA Optical Drive - Page 3
.... Installing a SATA Optical Drive
3 a Disconnect the SAS cable from the SAS controller and pull the cable away from the back of the optical drive.
6 PowerEdge 2900 and 1900 systems only: Perform the following steps.
Removing an Existing Optical Drive -
See your Hardware Owner's Manual.
3 Remove the system cover.
WARNING: Only trained service...
Installing a SATA Optical Drive - Page 4
...new SATA drive in the side of the drive.
4
Installing a SATA Optical Drive The PowerEdge 2900 and 1900 systems do not reuse the interposer board attached to the old drive.
1 Pull outward on... tray to release the interposer board connected to the optical drive. PowerEdge 2970, 2950, and 1950
For PowerEdge 2970 and 2950 systems, the optical drive tray that shipped with the SATA drive installation...
Installing a SATA Optical Drive - Page 5
Figure 1-1. Replacing the Optical Drive in a PowerEdge 2950 or 2970 System
2 1
3
4
5
6
7
1 optical drive 3 interposer 5 SATA power cable 7 optical drive carrier
2 interposer release latch 4 SATA cable 6 carrier latch
Replacing a PowerEdge 1950 Optical Drive
NOTE: The replacement drive tray provided in the side of the drive.
Installing a SATA Optical Drive
5 Release the rails to ...
Installing a SATA Optical Drive - Page 7
... 5 SATA power cable
2 SATA_A connector on the system and attached peripherals. See "SAS Controller Daughter Card" in your Hardware Owner's Manual.
6 Close the system. PowerEdge 2970 or 2950
1 Insert the optical drive tray into the system until it is fully inserted and locked into position.
2 Connect the SATA cable (the end with...
Installing a SATA Optical Drive - Page 8
... bracket toward the front of the system until the bracket detaches from the chassis slots.
6 Route the SATA cable in the cable channel in the PowerEdge 2950 and 2970
1
2
3 4 5
1 SATA_B connector on the system board.
Installing a SATA Optical Drive - Page 9
..." in the optical drive kit and connect one end to the optical drive and the other to the SATA connector on the system board. For a PowerEdge 1900, use the SATA_B connector.
-
Installing a SATA Optical Drive
9 See Figure 1-5.
- See "Installing the Cooling Shroud" in your Hardware Owner's Manual.
6 Replace the fans in the...
Installing a SATA Optical Drive - Page 10
... board
8 Reconnect the cables to the SAS controller daughter card.
9 Close the system. See "Closing the System" in a PowerEdge 2900 or 1900
3
2
4
5 1
1 optical drive 3 SATA data cable 5 SATA power connector on SAS
backplane (PowerEdge 2900 only)
2 SATA power cable 4 SATA connector on the system and attached peripherals.
10
Installing a SATA Optical Drive Figure...
Information Update - Page 2
... a potential for property damage, personal injury, or death. Microsoft, Windows, and Windows Server and are registered trademarks of your computer. Other trademarks and trade names may be used ..., the DELL logo, and PowerEdge are trademarks of data if instructions are registered trademarks of Dell Inc. CAUTION: A CAUTION indicates potential damage to change without the written permission of...
Information Update - Page 9
... of quad-core Intel Xeon processors. Safeguarding Encrypted Data
On PowerEdge 2950 III systems using Windows Server® 2008, you can use encryption programs, such as... system BIOS version is upgradeable to secure the contents of memory is fully supported.
PowerEdge 2950 III Systems
PowerEdge 2950 III systems have added support for the following approved 8-GB memory configurations: •...
Information Update - Page 10
...DIMM) so that node
for additional information
interleaving cannot be
for the PowerEdge 2950 III system and the probable cause and corrective action when the message... configuration does not support Node Interleaving. The memory configuration Ensure that supports
configuration has changed node interleaving. supported.
If the problem
persists, see
functionality. System Message Update
Table...
Information Update - Page 15
...:
• The system is off power to the system and restart the system. You can change the system ID and name in the Hardware Owner's Manual.
The LCD messages refer to maximum ... Support CPU Temp Interface
Causes
Corrective Actions
A 62-character string that can occur on the PowerEdge 2950 III system and the probable cause for critical failure events. If the problem persists, see ...
Information Update - Page 16
... AC power source. If the problem persists, the riser card or system board is out of acceptable range. LCD Status Messages (continued)
Code E1211
Text ROMB Batt
Causes
RAID battery is either missing, bad, or unable to recharge due to thermal issues. Corrective Actions
Reseat the RAID battery connector.
Remove and reseat...
Information Update - Page 21
... the interrupt assignment for PCI devices
Assignment
in China are shipping in the system. Changes take effect after the system reboots.
PXE support allows the system to the DMA engine.../OAT reduces system CPU usage
(Disabled default) for the PowerEdge 2950 III system. Integrated Devices Screen Option
Option
Description
Embedded Gb NIC2 Enables or disables the system's ...
Information Update - Page 24
This operating system is saved.
System Diagnostics Update
In the Customize window of operating systems on the Server OS Install tab. System Support for Microsoft Windows 2000
If you run the System Build and Update Utility, Microsoft® ...the file to specify the diskette drive or USB memory key where the test log file is supported by the PowerEdge 2950 and 2950 II systems, but not by the...
Information Update - Page 44
System Security
表 1-7 PowerEdge 2950 III TPM。
TPM Security（TPM TPM。
表 1-7. New System Security...27963;）
更改 TPM
设置为 Activate TPM。
设置为 Deactivate TPM。
No Change TPM TPM TPM Security （TPM Off
TPM Clear
（TPM No [ 否 ]）
TPM 将导&#...
Information Update - Page 46
Microsoft Windows 2000
System Build and Update Utility Microsoft® Windows® 2000 将位于 Server OS Install PowerEdge 2950 和 2950 II PowerEdge 2950 III
Customize Log output file pathname USB
46
信息更新
Information Update - Page 132
...; cat/sys/devices/system/cpu/cpuxx/cpufreq/scaling_ cur_freq
• RHEL 3 9 Intel Xeon 54xx proc/cpuinfo
RHEL 4
Microsoft Windows 2000
System Build and Update Utility Server OS Install OS OS Microsoft® Windows® 2000 PowerEdge 2950/2950 II OS PowerEdge 2950 III
Customize Log output file pathname USB
132
Information Update - Page 157
Microsoft Windows 2000
Microsoft® Windows® 2000 이 Server OS Install(서버 OS PowerEdge 2950 III 대신 PowerEdge 2950 및 2950 II
Customize Log output file pathname USB
157
Hardware Owner's Manual (PDF) - Page 20
... NAME
E1000 E1114
FAILSAFE, Call Support
Temp Ambient
E1116 Temp Memory
E12nn xx PwrGd E1210 CMOS Batt E1211 ROMB Batt
E1229 CPU # VCORE E1310 RPM Fan ## E1313 Fan Redundancy
Causes
Corrective Actions
A 62-character string that can change the system ID
The SYSTEM NAME displays and name in the System only. Setup program.
Specified...
Hardware Owner's Manual (PDF) - Page 27
... 1. For example, if you might be able to determine the problem if multiple related errors occur. when the temperature returns to the normal state.
W1228
ROMB Batt < 24hr Warns predictively that a microprocessor is full of Battery" on page 74.
For example, if temperature for a component goes out of these actions will lose...
Similar Questions
How To Reset Romb Batt Error E1211 On A Dell 2950 Poweredge
(Posted by jasGe 10 years ago)
Poweredge 1900 With An Error W1228 Romb Batt < 24 Hr.
What part do I order and where can I order it from quickly
What part do I order and where can I order it from quickly
(Posted by jyohn 11 years ago)
What Does It Mean E1211 Romb Batt
dell power edge 2900 error message
dell power edge 2900 error message
(Posted by Anonymous-54163 12 years ago)