Home » Denon » Home Theater Systems » Denon AVR 1603

Denon AVR 1603 Support Question

Find answers below for this question about Denon AVR 1603 - AV Receiver.
Need a Denon AVR 1603 manual? We have 2 online manuals for this item!

Denon Overview Questions Manuals Reviews Videos Research

Question posted by PaulAJoh1968 on September 9th, 2023

Wie Resetten Ich Meinen Avr-1603?

Wie resetten ich meinen avr-1603?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on September 9th, 2023 8:43 PM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,617,810

1,100
points

Um Ihren Denon AVR-1603 zurückzusetzen, müssen Sie die folgenden Schritte ausführen:

Schalten Sie den AVR aus.

Halten Sie die Tasten "STANDARD" und "STATUS" auf der Vorderseite des AVR gleichzeitig gedrückt.

Schalten Sie den AVR ein, während Sie die Tasten gedrückt halten.

Lassen Sie die Tasten los, wenn "INITIALIZED" auf dem Display angezeigt wird.

Der AVR wird nun auf die werkseitigen Standardeinstellungen zurückgesetzt.

Hier sind die Schritte im Detail:

Stellen Sie sicher, dass der AVR ausgeschaltet ist.

Suchen Sie die Tasten "STANDARD" und "STATUS" auf der Vorderseite des AVR.

Drücken Sie beide Tasten gleichzeitig und halten Sie sie gedrückt.

Schalten Sie den AVR mit der Netztaste ein.

Lassen Sie die Tasten los, wenn "INITIALIZED" auf dem Display angezeigt wird.

Der AVR wird nun neu gestartet und auf die Werkseinstellungen zurückgesetzt.

Bitte beachten Sie, dass nach einem Zurücksetzen alle Einstellungen verloren gehen. Sie müssen alle Einstellungen erneut vornehmen, einschließlich der Netzwerkeinstellungen, der Surround-Einstellungen und der Lautstärkeeinstellungen.

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Answer #2: Posted by Technoprince123 on September 9th, 2023 8:07 PM

Technoprince123

Member since:
February 8th, 2021

Points: 1,205,190

100
points

To perform a factory reset on your Denon AVR-1603, turn off the receiver and press and hold the "STANDARD" and "STATUS" buttons simultaneously on the front panel.

Please response if this answer is acceptable and solw your problem thanks

Related Denon AVR 1603 Manual Pages

Literature/Product Sheet - Page 1

... sources, and include these highfrequency components so that has been dramatically improved over Pro Logic. NEW MODEL I N F O R M A T I O N Dolby Digital and DTS A/V Receiver AVR-1603 With Dolby Pro Logic II for a New Way To Enjoy Home Theater The AVR-1603 A/V receiver with Dolby Pro Logic II and powerful output of 80 watts per channel lets you enjoy multi-channel...

Literature/Product Sheet - Page 2

... of Dolby Laboratories Licensing Corporation. *DTS is registered trademarks of the AVR-1603 to suit your home theater system, including codes for the main (left and right) speakers. BOX ...home. ■ High-grade Speaker Terminals (for speakers A): Large binding post speaker terminals has been provided for maximum ease-of-use of a second pair of DENON's high-grade A/V receiver, the AVR-1603...

Owners Manual - Page 3

... off before proceeding. ENGLISH 2 We greatly appreciate your purchase of the AVR-1603. 2 To be sure you take the following steps: • Install this unit as far as providing outstanding high fidelity reproduction of your favorite music sources. EXT. DTS (Digital Theater Systems) decoder DTS provides up during this time, the output will be...

Owners Manual - Page 4

...@9 Power operation indicator (ON/STANDBY) #0 INPUT SELECTOR knob .......(16, 18, 19, 24 ~ 26) System buttons 13, 14) SYSTEM SETUP/ SETUP button 9, 12, 14) Cursor buttons 9 ~ 12, 14, 18 ~ 22) STATUS/DISPLAY...15) DIMMER button 17) NOTE: • The shaded buttons do not function with the AVR-1603. (Nothing happens when they are pressed.) ENGLISH 5 PART NAMES AND FUNCTIONS Front Panel ...

Owners Manual - Page 5

...recording device. Step 1 (page 5 to 8) Choose the location to the AVR-1603's analog input terminals. • The AVR-1603's OPTICAL OUT terminal is an optical digital output terminal for connection of a ... V, 50 Hz Front speaker systems Set these steps. Never connect equipment whose capacity is above 100 W. ENGLISH 6 READ THIS FIRST This A / V surround Receiver must be generated if a connected...

Owners Manual - Page 8

... down , improve the ventilation around the set is cut off . CENTER SPEAKER SYSTEM FRONT SPEAKER SYSTEMS System A FRONT SPEAKER SYSTEMS System B Protector circuit • This unit is equipped with an impedance of lower ...of 12 to protect the speakers under 80 Hz. 8 (L) (R) SURROUND SPEAKER SYSTEMS • Precautions when connecting speakers If a speaker is cut off and the power...

Owners Manual - Page 9

... optimizing the timing with clothing, etc. Crossover Frequency Set the frequency (Hz) below which the audio signals are required to set up the listening room's AV system centered around the this unit. 1 Set the slide switch to "AUDIO". 2 Use the following buttons to set . (The included battery is to display the...

Owners Manual - Page 10

...level that cannot reproduce low sounds of below 80 Hz with sufficient volume. Small...... None...... System set up. (down ) button to enter the setting and switch to the surround speaker ...(down ) button to switch to the SPEAKER DISTANCE setting. ENGLISH Before setting up the system 1 Check that all the components are installed. Select this when using speakers that can be...

Owners Manual - Page 11

Select the value closest to 80 Hz. NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to the measured distance. L1: Distance from center speaker to listening position L2: Distance from front speakers to listening ...

Owners Manual - Page 12

... (down ) button to switch the auto surround mode NOTE: • TUNER and V. Once the system is set up , there is no need to make the settings again unless other multichannel format Dolby ... button if you want to start the settings over After setting up the system 1 Press the SYSTEM SETUP button to finish system set up . ENGLISH Setting the Digital In Assignment Input the type of ...

Owners Manual - Page 13

...5 To store the codes of another component in the memory, repeat steps 1 to 4. Tape deck (TAPE) system buttons 3 Press the ON/SOURCE button and the OFF button at "AUDIO" position. • Indicator flash. ..., TAPE DENON CDR/MD DENON (CDR) DVD/VDP DENON (DVD) DBS/CABLE ABC (CABLE) 13 Tuner system buttons 6 : Rewind 7 : Fast-forward 2 : Stop 1 : Forward play 0 : Reverse play ...

Owners Manual - Page 14

...operated with this remote control unit. 1. Digital video disc player (DVD, DVD SETUP) system buttons POWER : Power on/standby (ON/SOURCE) 6,7 : Manual search (forward and... 8,9 : Auto search (to the component's operating instructions. Digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons POWER : Power on/standby (ON/SOURCE) MENU : Menu RETURN : Return D, H, F, G : Cursor...

Owners Manual - Page 17

... selected, the input signals (Main unit) (Remote control unit) connected to the FL (front left), FR (front right), C (center), SL (surround left and right) speaker systems without passing through the 1 Front panel display • Descriptions of the unit's operations Turn the control clockwise. IN) setting, press the INPUT MODE (AUTO, PCM...

Owners Manual - Page 19

... can be heard only from the left/right speakers as the standard mode for autosound music systems (no video), and is set to the manuals of the respective components. Select one of...Panorama Control: This mode extends the front stereo image to include the surround speakers for A/V systems. The Emulation mode offers the same robust surround processing as shown below each time the button ...

Owners Manual - Page 20

... the display "Yes". (left) and (right) to OFF for correct Dolby Digital playback. COMP. (Initial) D.COMP. Set to the desired level according to the speaker systems being used and the source to be adjusted in the Dolby Pro Logic, Dolby Digital and DTS Surround modes. Press the SURROUND PARAMETER or default...

Owners Manual - Page 24

... the TUNING UP or DOWN button. 3 1, 4 2 (Main unit) (Remote control unit) • Automatic searching begins, then stops when a station is set, FM stereo broadcasts are received in the preset memory. (Remote control unit) To preset other channels, repeat steps 1 to set the manual tuning mode. At open frequencies, the noise is...

Owners Manual - Page 26

...sound imaging, and Dolby Digital offers tremendous dynamic range from above Surround The AVR-1603 is a new multi-channel playback format developed by Dolby Laboratories. LFE - ...sound tracks of movies recorded on ordinary stereo equipment, in a movie theater. The signals can be played on DVDs, LDs and video cassettes to... home surround systems Dolby Digital Dolby Pro Logic No.

Owners Manual - Page 27

... AVR-1603, or may be handled in which digital signals are fully independent, eliminating the risk of deterioration of the front channel being input. Once the set the mode to "ANALOG" or "PCM". 1 DVD Optical or coaxial digital output (same as in a movie theater, right in securely. • Check the insertion of Digital Theater Systems...

Owners Manual - Page 28

... Ω/ohms 5 Hz ~ 10 MHz - +1, -3 dB Y (brightness) signal - 1 Vp-p, 75 Ω/ohms C (color) signal - 0.286 Vp-p, 75 Ω/ohms 5 Hz ~ 10 MHz - +1, -3 dB 2 Tuner section Receiving range: Usable sensitivity: 50 dB quieting sensitivity: S/N ratio: Total harmonic distortion: [FM] (note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W) 87.50 MHz ~ 108...