EMC DS-16B Support Question
EMC DS-16B Support Question
Find answers below for this question about EMC DS-16B - Connectrix Switch - Fibre Channel.Need a EMC DS-16B manual? We have 1 online manual for this item!
Question posted by mrajabi61 on November 21st, 2010
What Is The User Name And Password For Emc Ds16b3 Switch?
what is the user name and password for EMC DS16B3 Switch?
Current Answers
Answer #1: Posted by DreadPirateRoberts on November 21st, 2010 7:09 AM
DreadPirateRoberts
Member since:
November 19th, 2010 Points: 8,633,403
Member since:
November 19th, 2010 Points: 8,633,403
Initial switch login typically is in a "non-privileged" mode. You must obtain an "Enable" (i.e., "privileged") password, if you need to perform privileged tasks such as making switch configuration changes. At the switch prompt, after you log in, type "ena" and then press "Enter;" type the "enable" password, and then press "Enter." If you see the "#" prompt, you are now in privileged mode.
So basically unless you set up the password there is no username or password, just telnet in and make the adjustments.
So basically unless you set up the password there is no username or password, just telnet in and make the adjustments.
Related EMC DS-16B Manual Pages
Installation Guide - Page 1
... rack placement requirements for mounting them in Figure 1. RKH/RKL 5 • Installing the DS-16B2 Rails 10 • Installing the DS-16B2 Switch 21
EMC Departmental Switch DS-16B Installation Guide
1 It also describes the kits available for the 16-port EMC departmental switch shown in EMC and non-EMC Racks and includes installation instructions as well. Device 16-port departmental...
Installation Guide - Page 3
...: 100 to 240 V ac, 47 to 63 Hz
Cooling Requirements (Heat Dissipation)
368.5 BTU/hr
Maximum Weight 12.9 kg (28.5 lbs)
Device Dimensions
Device
DS-16B2 switch
DS-16B2 switch with rails
Height 4.34 cm 1.0 U 4.44 cm
Depth 1.71 in 61.00 cm 24.01 in 1.75 in 61.00 cm 24.01 in...
Installation Guide - Page 4
...DAE (3.5 U)
DAE (3.5 U) DAE (3.5 U)
DAE (3.5 U)
DPE (6.5 U)
Figure 2
SPS (1 U)
Front Sample Cabinet Installation
4
EMC Departmental Switch DS-16B2 Installation Guide
Rear
EMC2056 Note: Switch bezels are removed for the switch and the switch power rating listed in the table on the location of the DS-16B2 switch in pairs. Power distribution must support the number of the rack/cabinet in...
Installation Guide - Page 5
... cords as listed in the table below for your PDU)
DS-16B2-RKL kit only)
EMC Departmental Switch DS-16B2 Installation Guide
5 Component
Use
2 switch mounting brackets - See the figure below . see illustration on page 21.
2 per switch
2 short rail assemblies (20.5 inches to 27 inches)
2 per switch
2 long rail assemblies (27 inches to 34 inches)
2 per...
Installation Guide - Page 6
RKH/RKL)
Switch Mounting Brackets
Front Rails
Bezel
Short Rear Rails
Bezel Supports
Figure 3 Rails. Bezel, and Power Cords
Long Rear Rails
Ac Power Cords
EMC2042
6
EMC Departmental Switch DS-16B2 Installation Guide Switch Mounting Kit (DS16B2 -
Installation Guide - Page 7
... long rails, used in the rail. EMC Departmental Switch DS-16B2 Installation Guide
7 Switch Mounting Kit (DS16B2 -
The rail assemblies for a detailed list of all the securing hardware that is included in the switch mounting kit. RKH/RKL)
Screws, Nuts and Washers See the table below for the EMC CLARiiON® rack come pre-assembled, with...
Installation Guide - Page 8
... DS-16B2 in square-hole channels. M3 x 8-mm pan-head screw (Qty. 6) Ball stud (Qty. 2)
1 per bezel, to secure the bezel to the rail assembly.
2 per switch mounting bracket. Switch Mounting Kit (DS16B2 - Used to secure mounting brackets to the rails.
2 per bezel support, to secure the bezel support to the rail assembly.
8
EMC Departmental Switch DS...
Installation Guide - Page 9
Tools Required:
#1 Phillips Screwdriver
6-mm (1/4-in.) 8mm (5/16-in.)
Nut Driver
Nut Driver
EMC2065
EMC Departmental Switch DS-16B2 Installation Guide
9
Switch Mounting Kit (DS16B2 - RKH/RKL)
Tools Required for Installation You will need the following tools to complete the installation of the rails and switch(es).
Installation Guide - Page 10
Front
Rear Door Removed for the DS-16B2 rails.
Figure 4 shows a view of the Rails Installed in a 39 U rack/cabinet. Installing the DS-16B2 Rails
Installing the DS-16B2 Rails
This section describes the installation procedures for Clarity
Rear
Figure 4 View of the rails installed in a 39 U Rack/Cabinet
10
EMC Departmental Switch DS-16B2 Installation Guide
EMC2071
Installation Guide - Page 11
... contains 2 different length rear rail mounts, be sure to use the rail length that is appropriate for third Party Racks/Cabinets)
EMC Departmental Switch DS-16B2 Installation Guide
11 Installing the DS-16B2 Rails
DS-16B2 Rails Installation There are two different length rails as shown in Figures 4 and 5: The short rails range between 27...
Installation Guide - Page 12
See Figures 7 and 7 below. Installing the DS-16B2 Rails
The front and rear flanges of the DS-16B2 Rails
EMC2070
12
EMC Departmental Switch DS-16B2 Installation Guide Screw Holes
Front Rails
Figure 7 Front Flange of the DS-16B2 Rails
Short Rear Rails
EMC2069
Screw Holes Screw Holes
Figure 8
Long Rear Rails
Rear Flange of the DS-16B2 rails have three screw holes.
Installation Guide - Page 13
... Washer (2)
Short Rear Rail
Front Rail
Ac Power Cord
Figure 9
Ac Power Cord
Front Rail
DS-16B2 Rails Assembly
Short Rear Rail
#10 Flat Washer (2)
Keps Nut (2)
EMC2044
EMC Departmental Switch DS-16B2 Installation Guide
13 Installing the DS-16B2 Rails
Select the appropriate length rails, and follow the steps below for an illustration of...
Installation Guide - Page 14
...adjusted once the switch is a new installation in an EMC CLARiiON rack, the rails are installing the switch in the Front Rail
Rack Rear/ Plug into PDU
EMC2068
14
EMC Departmental Switch DS-16B2 Installation Guide... front rail. Ac Power Cord
Lip
Rack Front/ Plug into Switch
Front Rail
Figure 10 Installing the ac Power Cord in a non-EMC rack/cabinet.
1. Run the front end of the power cord...
Installation Guide - Page 15
...
3. Secure the adjustable rail to the front rail with two #10 flat washers and M5 keps nuts. Insert the slots of Keps Nuts
EMC2066
EMC Departmental Switch DS-16B2 Installation Guide
15 Keps Nut
Figure 11 Location of the rear adjustable rail onto the threaded posts on the front rail, thereby capturing the...
Installation Guide - Page 16
..., the keps nuts can be tightened after the rails have been installed.
16
EMC Departmental Switch DS-16B2 Installation Guide Keps Nut
Keps Nut
Figure 12 Securing the Keps Nuts
EMC2045
If... the side skins are adjusted to fit between the channels in the rack/cabinet you will locate the switch....
Installation Guide - Page 17
... page 8). Hand-tighten the ball stud. Repeat steps 1 through 5 for the ball stud.
2. Secure the rail to a round-hole channel with 2 M5 x 10-mm panhead screws (see table on page 8). EMC Departmental Switch DS-16B2 Installation Guide
17 NOTE: The ball studs support the bezel.
4. Position the #10 flat washer and ball stud in...
Installation Guide - Page 18
Rack Rear
Rear
M5 x 10-mm Pan Head Screw (8)
Front
Figure 13 Installing Rails in Round-Hole Channels
EMC2046
18
EMC Departmental Switch DS-16B2 Installation Guide Installing the DS-16B2 Rails
Align the rear rail flange to the inside of the channel. Rack Front
Align the front rail flange to the inside of the channel.
Installation Guide - Page 19
... holes of the front rail flange to the inside channel, as shown in the square-hole channel of the front channel. The top and bottom screw holes are used for the other rail. EMC Departmental Switch DS-16B2 Installation Guide
19 Installing the DS-16B2 Rails
Square-Hole Channel
Follow the steps below to install the rails assembly...
Installation Guide - Page 20
M5 x 16-mm flat head screw (Qty. 8)
Rack Rear
Align the rear rail flange to the inside of the channel. Square-Hole Washer (Qty. 8)
Figure 14 Installing Rails in Square-Hole Channels
EMC2047
20
EMC Departmental Switch DS-16B2 Installation Guide Installing the DS-16B2 Rails
Rack Front
Align the front rail flange to the inside of the channel.
Installation Guide - Page 21
... 8). Pan Head Screw Switch (6) Mounting Bracket
Hole
Figure 15 Attaching the Switch Mounting Brackets
Switch Mounting Bracket
EMC2048
EMC Departmental Switch DS-16B2 Installation Guide
21 Secure...channel of the switch. 2. Place the bracket against the switch. Installing the DS-16B2 Switch
Installing the DS-16B2 Switch
This section describes the procedures for installing the DS-16B2 switch...
Similar Questions
Need To Reset Password Back To Old Password How Can I Do That?
(Posted by Melaniehollingshead 11 years ago)
Emc Ec-1500 - Connectrix Model C Network
what is the dimension of the cabinet
what is the dimension of the cabinet
(Posted by leopoldong 13 years ago)
I Need One 512 Mb Memory Chip For Ax150sci
The unit reports: The write cache is currently disabled. The write cache is disabled when faulted co...
The unit reports: The write cache is currently disabled. The write cache is disabled when faulted co...
(Posted by bsirotin 14 years ago)