Home » Frigidaire » Laundry Dryers » Frigidaire GLEQ2152ES

Frigidaire GLEQ2152ES Support Question

Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.
Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!

Frigidaire Overview Questions Manuals Reviews Videos Research

Question posted by Rayberkin on June 19th, 2012

E68 Key Stuck

My LEQ700EGO Electric Dryer keeps cutting out .. Displays E68 Key Stuck .. The keys seem free, the next suggestion is to replace the control , how do I get to that? And is there any thing else I could try??

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by OnlineOutreachSpecialist on June 20th, 2012 8:46 AM

This answer was accepted by the poster of the original question.

OnlineOutreachSpecialist

Member since:
March 30th, 2011

Points: 2,848,280

1,100
points

The control board is behind the control panel, and in some units, underneath the unit itself. You cannot typically do this on your own. I would contact Frigidaire at 888-203-1389 so you do not void any remaining warranty and Frigidaire is responsible (work wise) for their people who service it.

Online Outreach Specialist

Related Frigidaire GLEQ2152ES Manual Pages

Use and Care Manual - Page 2

...the Operating Instructions included with your Purchase Date dryer. This symbol alerts you don't follow ... YOU SMELL GAS: • Do not try to prevent property damage, personal injury or loss...and NLPWD15E (Black) specifically designed for this or any electrical switch; These words mean: DANGER You will identify the...et de série • Service Keep it shall be used when elevating the ...

Use and Care Manual - Page 3

...not place items exposed to cooking oils in your dryer has a drying rack, always replace the lint screen when finished using this dryer, comply with the basic warnings listed below. ...dryer at any time. • Do not use an adaptor plug or extension cord or remove grounding prong from electrical power cord. Some rubber materials, when heated, can become airtight chambers. • Keep laundry...

Use and Care Manual - Page 4

...of fire, electrical shock, or injury to 1/2 full. Fill out the load with controls. - The dryer will fill the drum 1/3 to persons, read and follow fabric care labels and laundry product labels.... switch automatically turns off the motor in the unlikely event of a gas dryer must replace the thermal limiter switch after correcting the fault. • Failure to a new location, ...

Use and Care Manual - Page 5

...; Before cleaning the dryer interior, unplug the electrical power cord to the INSTALLATION INSTRUCTIONS for items containing plastic, foam rubber, rubber-like materials, feathers or down. 5. The screen is opened to persons or property, comply with a damp cloth and a mild liquid household cleanser. CAUTION -Risk of Fire - Dry thoroughly and replace. End of...

Use and Care Manual - Page 6

... items in washer or dryer to electricity. • Or, add a fabric softener sheet and reduce static electricity. • Lint screen...dryer. • Remove items as soon as cycle ends. 6 They can damage the finish or controls...con't Do not store or place laundry products on top of dryer at medium or low heat for ...suggestions provided by The Soap and Detergent Association. Rinse and rewash.

Use and Care Manual - Page 7

... label instructions. Always remove foreign objects from drum and restart dryer. OCCURRENCE Dryer does not start. Thermal limiter tripped. Reset circuit breaker or replace fuse. Dryer runs but the heater will be 20% longer than two 90° bends and must be loose. Replace fuse. Electric dryer is connected to make sure supply valve is empty or...

Technical Data Sheet - Page 1

... times the lights flash. If dryer operates normally but the key struck code still exists, replace electronic control. Disconnect wire going to the next code, press the OPTIONS button. If button is free but code returns, replace electronic control. Check for six seconds. 3. Clear code, exit mode and start dryer. CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING Please Return This...

Technical Data Sheet - Page 2

...(press in the display.** 2 O'clock: Drive motor runs; heat source is lit. When the TEMP key is pressed, all the TEMP LED's should light. When the OPTION or Select key is pressed, all ...seconds. "H" and the control thermistor reading will be reset for six seconds or disconnect power from dryer. Drying LED is lit. In controls that do not have a digit display, the dryness LED'S are...

Installation Instructions - Page 2

... ELECTRIC Dryer CIRCUIT - branch circuit fused with clothes dryers. The dryer is in the installed position. Duct tape. 6. Vent hood. 8. NEMA 10-30R NEMA 14-30R GAS Dryer CIRCUIT - POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz, Alternating Current. WHAT TO DO IF YOU SMELL GAS · Do not try to prevent property damage, personal...

Installation Instructions - Page 3

...has a swing-out damper(s) that open when the dryer is free of any area of water column, the system is installed in the charts...to exhaust the dryer. If the system back pressure is less than 0.75 inches of plastic duct or metal foil duct, replace it must be ... drying times and fire hazards. The dryer exhaust system MUST be exhausted into the laundry area. Exceeding the length of duct pipe...

Installation Instructions - Page 4

...) 13 1/2" (34 cm) 4 3/8" (11 cm) 3 3/4" (9.5 cm()9.5 cm) GAS SUPPLY REQUIREMENTS Replace copper connecting pipe that will obstruct the flow of combustion and ventilation air. 3. Floor MUST be inspected and ...a solid door. 4. DO NOT install your parts distributor. However, on electric dryers, exhausting can be disconnected from the gas supply piping system during any pressure...

Installation Instructions - Page 5

inches (387.1 sq. cm) CLOSET DOOR 0" (0 cm) 15" (38.1 cm) 1" (2.54 cm) 0" (0 cm) 5 This dryer MUST be exhausted outdoors. 5. cm) 60 sq. Inches (cm) Alcove Closet SIDES REAR TOP FRONT 0 (0 cm) 0 (0 cm) 15 (38.1 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm) 1 (2....

Installation Instructions - Page 6

Dryer Installation Dimensions Free-Standing & Under Counter 48.5" To clear open door (123.19cm) Electrical supply on rear of unit 36.0" Gas supply pipe on rear of unit ...) 2.375" (6.03cm) (34.29cm) 13.5" To rear & base exhausts 27.0" (68.58cm) Stacked Dryer Installation Dimensions (68.58cm) 27.0" Electrical supply on rear of unit 28.25" to front of cabinet(71.76cm) 28.75" to clear knobs ...

Installation Instructions - Page 7

...). REMOVE 4 SCREWS (ONE FROM EACH HINGE FIRST) 7 This dryer MUST be 4 inches (10.16 cm) in the open screw holes on its left side of the door opening . CAN/CSA C22.2 (latest editions) for future installation. To prevent damage, do not use the control panel as a means to the floor. Conversion is...

Installation Instructions - Page 8

... the door opening using the four screws removed in Step 2. 4. Be careful to the dryer front panel. Remove the two hinges and reinstall the four screws. Note the installation orientation of... knife to avoid scratching the paint. 2. Open the dryer door. Remove the screws from each hinge first. NOTE: You may need a plastic knife to keep it 180°. Remove the two handle hole plugs...

Installation Instructions - Page 9

... be grounded. Refer to the pre-installation requirements in the cord. If in this dryer. Locate the dryer within reach of the equipment grounding conductor can create electrical shock and/or a fire hazard. Do not cut by a path of your dryer. approved strain relief must be plugged directly into an appropriate, copper wired receptacle that...

Installation Instructions - Page 10

... WIRE RED BLACK TIGHTEN NUT WHITE TO THESE THREADS NUT STRAIN RELIEF MOUNTING BRACKET STRAIN RELIEF MOUNTING B R A C K E T POWER CORD POWER CORD ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM ELECTRIC Dryer ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the...

Operating Instructions - Page 1

... Dry cycles take the guesswork out of ventillation system, electrical voltage or gas pressure can also affect drying time. ...to delete an option. The dryer senses the moisture level of the load as it will automatically be displayed for a desired option flashes,... load, weight and fabric type. It also has many suggestions for towel loads. It has important safety and warranty information...

Operating Instructions - Page 2

... options will not light. No Heat should only be displayed for most cotton fabrics. Occasionally a load may seem ... To change settings. To increase drying time for wrinkle free, permanent press and lightweight fabrics. Drying times from overdrying... cycle or dryness level. Dryer Features Control To avoid having someone accidentally start or stop the dryer, press OPTIONS and SELECT ...

Operating Instructions - Page 3

...Code 4 beeps / E4A Error Dryer ran too long 6 beeps / E68 Push button does not function Possible... ** Not recommended * * * * * * *** Estimated cycle duration is displayed, an error has occured. DRYER SETTINGS CHART AVAILABLE CYCLE SETTINGS - ERROR CODE CHART If the dryer stops, the status lights flash, the signal beeps and a code is based... Checklist" in the control panel.