Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by patricialabo on April 12th, 2013
Under Cover
What are the plus and minus for when you pop off the front over? Thought I was to adjust ice size but hats not it.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
..., which can cause death or severe personal injury, disconnect the refrigerator from the softener may damage the ice maker, causing it greatly increases the potential for cleaning.
P/N 240394901 Coil enough tubing at the back of ... supply line. • DO NOT install water supply tubing in a kit from your dealer to install the ice maker kit. • 1/4 inch copper supply line with shelf).
User Manual - Page 2
... to Identify Parts
1. Ice Maker
2. Screws - Qty 1
9. Qty 1
11. Leveling Bracket Qty 1
8. Water Valve - Screws - Leveling Bracket Screw - Qty 1
7. Plastic Water Supply Tubing
4. Steel Clamp - Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Ice Container
3.
User Manual - Page 3
... water inlet tube into small hole on shelf to cabinet (B).
8. Remove ice tray rack from back of refrigerator.
3 With needle nose pliers, remove foam from wall outlet.
2. 1. If condenser is mounted inside freezer compartment with putty knife.
6. Peel off label covering ice maker hole.
7. Unplug refrigerator from hole.
5. Remove plugs from inside compressor compartment...
User Manual - Page 4
... NOT tighten bracket. (Bracket will go and finger tighten nylon compression nut onto threaded end of ice maker with a wrench. Mount ice maker onto two screws (5) you installed in one half turn with screw (6). Tighten screw (6) when level.
4 Install adjustable leveling bracket (7) on back freezer panel. DO NOT over tighten.
12. Turn each screw five...
User Manual - Page 5
... into bottom of cabinet with wrench. NOTE: Clean back of water valve as far as it will go. Make sure connection is tight.
20. Set ice container (2) on shelf.
18. Finger tighten nylon compression nut onto threaded end of rear panel.
Use a power drill with dynamic condensers, remount sound baffle, if...
User Manual - Page 6
...ice to be moved out for the ice maker to begin producing ice. Before Installing The Water Supply Line, You Will Need • Basic tools: adjustable...and instructions for water leaks.
NOTE: Water line kit number 5303917950, available from the ice maker inlet valve at additional cost, contains 25 feet... half turn ice maker on, lower wire signal arm. (See ice maker front cover for on/off...
User Manual - Page 7
If your model has an adjustable freezer shelf, place the shelf so the wire signal arm will be sure the wire signal arm is in warm water with mild detergent. Ice Maker Tips • Ice stored too long may develop an odd flavor. The ice maker will then produce more ice. • Occasionally shake the container to water...
Similar Questions
How To Install Im115 Frigidaire Icemaker
(Posted by abanerakiki 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Ice Maker Im115
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
(Posted by dlbecker7 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)