Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by IonArashwan on February 23rd, 2014
How Long For Frigidaire Ice Maker To Make A Cycle
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... be responsible for any damage if plastic tubing is not tied into a water softening system. The following items will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures fall below freezing. • Connect the...
User Manual - Page 2
... Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Leveling Bracket Screw - Plastic Clamp - Qty 1
11. Qty 1
7. Steel Clamp - Water Valve - Ice Container
3. Water Inlet Tube - Plastic Water Supply Tubing
4. Qty 1
9. Screws - Leveling Bracket Qty 1
8. Ice Maker
2. Qty 2
5. Qty 2
6. Use This Page to Identify Parts
1.
User Manual - Page 3
...and pull on back of refrigerator. Remove and save screws. Peel off label covering ice maker hole.
7. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser ... surface of inlet tube is mounted inside freezer compartment with putty knife.
6. Remove ice tray rack from inside compressor compartment (D), remove screws securing sound baffle to remove....
User Manual - Page 4
.... Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.)
13. Turn each screw five turns clockwise.
14. Make sure water inlet tube (11) is tight.
10. Install adjustable leveling bracket (7) on back freezer panel. Adjust leveling bracket (7) to level ice maker (1). Mount ice maker onto two screws...
User Manual - Page 5
...Phillips® head bit to drive the two self drilling screws (4) through cabinet liner. DO NOT over tighten.
16. Make sure connection is tight.
20. Secure plastic water tubing to water valve. See step 5.
5 Use a power drill...15. Push plastic water supply tubing into cabinet.
19. Set ice container (2) on shelf.
18.
Tighten another one half turn with two plastic clamps (9).
User Manual - Page 6
... cap.
4. NOTE: Water line kit number 5303917950, available from the ice maker inlet valve at the back of ... ON water supply at shutoff valve.
3. New plumbing may cause ice maker to cycle two or three times before connecting a water supply line to rear... power before making a full tray of arm.)
IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Slide brass...
User Manual - Page 7
... off . • The following sounds are normal when the ice maker is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. Ice Maker Tips • Ice stored too long may develop an odd flavor. Do not connect the ice maker to keep ice separated. • Keep the wire signal arm in its
“down” or...
Similar Questions
How Fast Should A Frigidaire Ice Maker Make Ice
(Posted by demowlg 10 years ago)
How Often Does Im115 Ice Maker Makes Ice
(Posted by vgartili 10 years ago)
Is There An Adjustment To Make The Ice Maker Make More Or Less Ice?
(Posted by cowboybrc 12 years ago)
Ice Maker Makes No Ice But Water Works.. I Replaced The Filter.
originally it made ice and no water. now it makes water and no ice! I replaced filter. please help
originally it made ice and no water. now it makes water and no ice! I replaced filter. please help
(Posted by Taurus176 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)