GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by Axelrod6 on April 23rd, 2013
My Ge Atp 1000 Keypad Gets Blazing Hot. It Is Newly Installed Over Heating Duct.
Is it defective or does it need to be moved? Why would this happen?
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...gang box installation • Saw or utility knife for cutting wallboard
Guidelines
• Mount the touchpad in ...security systems (see the "Specifications" section).
Table 1: Touchpad Power Usage
Current (mA) 110
60 12
Conditions
Maximum alarm current with basic system operating commands. Touchpad Wire Length Between Touchpad and Panel
750 feet 300 feet
1 Tools and Equipment Needed...
Installation Instructions - Page 2
...installations, cut a hole in the wall in the wire access area of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5.
Separate the mounting plate from the touchpad by first loosening the screw, then lift the touchpad...into the bottom of the touchpad.
2
ATP1000 Touchpad/Display Installation Instructions Gently tighten the screw ...
Installation Instructions - Page 3
... newly installed touchpad (such as a programming touchpad, be careful not to the Programming Touchpad Header on the panel. With the panel powered up the panel and verify correct communication between the panel and touchpad is correct.
2.
Connecting a Programming Touchpad-Concord Express Shown, Concord Similar
2. ATP1000 Touchpad/Display Installation Instructions
3
Alphanumeric touchpads...
Installation Instructions - Page 4
... device and its device name. 3. The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6:
1. To adjust display contrast:
1. Press , and the display briefly shows DONE, then shows the time and date.
4
ATP1000 Touchpad/Display Installation Instructions Testing
Adjusting Display Brightness and Contrast
3. Enter program mode by pressing 9 + user...
Installation Instructions - Page 5
... and hold the D and 6 buttons together for at touchpad and panel terminals.
2. However, if the new touchpad unit number has never been
ATP1000 Touchpad/Display Installation Instructions
5 The display shows ENTER _. 3. The display should show DA n, where n is the new touchpad unit number.
4. Note At this page). (Concord panels with software versions 1.01.6 only.)
Changing the...
Installation Instructions - Page 6
...;hqh UrpuvphyÃT
6
ATP1000 Touchpad/Display Installation Instructions For systems with the limits for more information on deleting unused unit numbers.
Concord is a trademark of the following measures:
...User
Changes or modifications not expressly approved by GE Interlogix can radiate radio frequency energy and, if not installed and used by any bus failures should operate...
Similar Questions
Hot Keypad
My keypad is installed on top of a heat duct. It becomes very hot - much hotter than the surrounding...
My keypad is installed on top of a heat duct. It becomes very hot - much hotter than the surrounding...
(Posted by Axelrod6 11 years ago)
How To Set Time And Date On Ge Atp-1000 Keypad
(Posted by melodale 11 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)
Can The Ftp-1000 Keypad Be Used To Program A Concord 4 Panel?
(Posted by barbgreg2004 12 years ago)