GE GFC720F Support Question
GE GFC720F Support Question
Find answers below for this question about GE GFC720F - 3/4 HP Continuous Feed Disposer.Need a GE GFC720F manual? We have 1 online manual for this item!
Question posted by kensandybuss on January 15th, 2015
Electric Hook Up
how do you get the plate off where the electrical connections are on a ge food disposal GFC720f?
Current Answers
Related GE GFC720F Manual Pages
Use and Care Manual - Page 1
...; Food Waste Disposer
GEAppliances.com
Safety Instructions
Connecting Electricity 2, 3 Safety Precautions 2
Installation Instructions
Attaching the Discharge Elbow 6 Components and Installation of Sink Flange 5 Connecting Disposer to Sink Flange 7 Dimensions/Typical Installations 8 Dishwasher Connection 6
Operating Instructions
Batch Feed Models 9 Care and Maintenance 10 Continuous Feed...
Use and Care Manual - Page 2
... switch side.
2
HOW TO CONNECT ELECTRICITY
If you are half-hot. DANGER: Improper connection of electric shock. The batch-feed or "TC" model
connects to the hot side, while the continuous feed
model connects to reduce the risk of the
equipment-grounding conductor can result in place to clear a jam or remove an object from a waste disposer, only use a long...
Use and Care Manual - Page 3
... two ways:
1. Connect the disposer to white wire on the appliance. Trace lead connected to this connection.
If you can connect it in a risk of least resistance for the ground wire. This means one unless metal cable is always hot. The batch-feed or "TC" model connects to the hot side, while the continuous feed model connects to exceed 36...
Use and Care Manual - Page 4
... responsibility of any materials to prevent leaks. PREPARATION
1. Be sure to Consumer - Disconnect electrical power supply to Installer - Inspect drain line. NOTE: Top and bottom of sink surfaces...pipe • Power cord kit (Part Number PM3X215)
4 Installation Instructions
Disposer
If you have questions, call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
...
Use and Care Manual - Page 5
...Bottom Bead
slight pressure. From under the sink.
Unscrew the support ring from the disposer by the factory. You are no putty is used instead of plumbers putty with ...Groove Hopper
Dishwasher Discharge Inlet
Elbow Gasket
Disposer
End Bell (Electrical Connections)
Elbow Flange
Rating Label in This Area
*Not used with batch feed model
Screws
Discharge Elbow
INSTALLATION OF ...
Use and Care Manual - Page 6
... the dishwasher hose using a hose clamp. Hose Clamp
Stepped Rubber Adapter
3 ATTACHING THE DISCHARGE ELBOW
CONNECT DISCHARGE ELBOW
Connect the discharge elbow to the disposer.* Make sure all plumbing connections are connecting to a dishwasher, complete the following step.
Rubber Gasket
Discharge Elbow
6
If a dishwasher is different, you are tight.
* Some installations (see...
Use and Care Manual - Page 7
... tight. Turn the mount ring about 1/4″ to the hopper projection. Hopper projections must be to the right until the disposer discharge elbow lines up the disposer under the sink flange.
Installation Instructions 4 CONNECTING DISPOSER TO SINK FLANGE
1 ATTACH TO SINK FLANGE
Line up with the outlet pipe (see page 8). Mount Ring Slot
Hopper...
Use and Care Manual - Page 8
...5 9/16"
4 1/2" 11/2"
GFC720 Model Series
8 1/2"
93/8"
165/8"
5 9/16"
4 1/2" 11/2"
GFB760 Model Series Batch Feed Operation
8 1/2"
7 1/4"
161/16"
5 9/16"
4 1/2" 11/2"
GFC1020 Model Series
SOME TYPICAL INSTALLATIONS
Direct replacement for most makes ...essential for the proper operation of the disposer that this dimension be 9″-12″, depending upon the models listed above, ...
Use and Care Manual - Page 9
...disposer.
E.
C. To speed up food waste disposal, cut or break up with the switch
plunger. Before turning the disposer off . Do not use hot water while running the disposer. Batch Feed Models
A. C. Scrape in food...com
This disposer uses anti-jam swivel impellers that
the largest slot lines up with the switch plunger inside the neck of cold water. Continuous Feed Models
...
Use and Care Manual - Page 10
... guard for the Batch Feed model, is properly seated.
C.
To replace, insert into the sink flange and push down until it out from falling into the disposer, as large bones, fibrous...and maintenance.
I If an odor develops, run orange or lemon rinds through the disposer.
TO SPEED UP FOOD WASTE DISPOSAL...Cut or break up large bones, melon rinds, grapefruit skins and corn cobs....
Use and Care Manual - Page 11
... shorted or broken wire connecting to call for service....disposer.
Defective cushion mount. Dislodge the object by :
1. Improper seating of elbow flange screws.
*Batch Feed...electrical components are intact, the unit may be caused by improper tightening of sink flange (gasket choice, putty or tightening).
2. Troubleshooting Tips Save time and money! Replace the splash guard.*
the disposer...
Use and Care Manual - Page 12
... schedule service on-line, visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737).
For The Period Of: GE Will Replace:
Staple your state's Attorney General.
12
Warrantor: General Electric Company. Proof of the original purchase
The entire disposer if there is needed to state. One Year From the date of...
Similar Questions
Ge Gfc325f Disposal
My disposal was jammed, I unjammed it using a butter knife around the edges to remove the broken gla...
My disposal was jammed, I unjammed it using a butter knife around the edges to remove the broken gla...
(Posted by lemleyr70 5 years ago)
Disposal Makes Hum Noise
Hello. My GE GFC325 garbage disposal is making a humming sound when I turn the disposal on. How do I...
Hello. My GE GFC325 garbage disposal is making a humming sound when I turn the disposal on. How do I...
(Posted by lizzybizzy50 7 years ago)
Reset Botton On G E Gfc720f Garbage Disposal
(Posted by Anonymous-60916 11 years ago)
