GE NX-1448E Support Question
GE NX-1448E Support Question
Find answers below for this question about GE NX-1448E - Security NetworX 48-Zone Fixed.Need a GE NX-1448E manual? We have 1 online manual for this item!
Question posted by gg on February 12th, 2012
Nx-1448e Battery
Power on panel is flashing. Manual says battery is low...WHERE IS BATTERY?
Current Answers
Related GE NX-1448E Manual Pages
User's Manual - Page 2
...if enabled)
Fire
Auxiliary Emergency
Police
Abort Delay (s) Auto Bypass (s) Auto Instant Battery Test
PROGRAMMED FUNCTIONS Cancel Alarm Change Partitions Chime Communicator Test
Forced Arming (s) Group Bypass... Entry Delay Time _______
Page 2
NX1448E Icon Keypad SECURITY SYSTEM NOTES
Installing/Service Company For Service Call Central Station
Duress Code
This system is
is not
...
User's Manual - Page 4
...have of your security system should read and follow the instructions in this manual you should notify your installing company. You should be aware of security.
All users of the security system and how...your home/business. The system must always be able to help you may be disarmed using a 4 or 6 digit code. Keep in mind, the level of the complete system.
INTRODUCTION
This manual is...
User's Manual - Page 5
...all situations.Use qualified security professionals to install and maintain your security control system. Care should be done with AC Power removed to arm the security system without power. NX1448E Icon Keypad
...and instructions carefully before operating your security system. Smoke and heat detectors may be possible to verify the battery is connected and adequately charged. Warning devices...
User's Manual - Page 6
... 11 CHIME LIGHT 11 EXIT LIGHT 11 FIRE ICON 11 INSTANT ICON 12 LISTEN-IN ICON 12 POWER ICON 12 READY / NOT READY ICON 12 SILENCED ICON 12 STAY LIGHT 12 TAMPER/TROUBLE ICONS 12 ZONE ICON 12 KEYPAD FUNCTIONS 13 ARMING YOUR SYSTEM IN THE "AWAY" MODE 13 ARMING YOUR SYSTEM...
User's Manual - Page 7
... CONTROL TONES (BEEPS 25 EMERGENCY EVACUATION PLANS 26
NX1448E Icon Keypad
Page 7 (Table of Contents continued...)
DISARMING THE SYSTEM 15 CANCEL / ABORT FEATURE 16 BYPASSING ZONES 16 GROUP BYPASS 16 UNBYPASSING 17 TURNING THE DOOR CHIME ON AND OFF 17 CHANGING USER CODES 17 ASSIGNING USER CODE AUTHORITY LEVELS 18 OTHER...
User's Manual - Page 8
...data is opened. An option that allows the keypad to disarm. An option that allows a special code to be "force armed" will flash the ready icon. (Note: Those zones that are not ready will not create an alarm.) A Function Code is either a four (4) or six (6) digit code that has... 99 four-digit codes or 66 six-digit codes, but not a mixture of access an individual has when using an alarm panel.
User's Manual - Page 9
... or six (6) digit entry code used to turn on (ARM) the security system by pressing either the [STAY] or [EXIT] key on the keypad...company.
Partitioned System Perimeter Quick Arm
User Code
A system divided into multiple areas in Power Service
Instant Enter Code Trouble FIRE Silenced Tamper
1 2 3 4 5 6 7 ... 41 42 43 44 45 46 47 48
NX1448E Icon Keypad
Page 9 An option that allows you to...
User's Manual - Page 10
Auxiliary Emergency Key - If your system is connected to a monitoring center, an emergency report could be transmitted to that center. If your security system will respond to the monitoring center. Fire Key - This key can activate the auxiliary alarm when pressed for two seconds. This key can sound a ...
User's Manual - Page 11
...LIGHT
The chime light is "on" when the chime feature is flashing in a trouble condition. Please note that a fire zone is bypassed.
CANCEL LIGHT
The cancel light will cause the cancel.... BYPASS LIGHT
The bypass light is "on" when any zone in this light is bypassed will flash during the exit delay. A rapidly flashing fire icon means that the light will also be illuminated. ...
User's Manual - Page 12
...power is delayed. If a zone icon is "flashing" rapidly, it means that zone is in alarm or has been faulted. POWER ICON
The power icon is on page 23 of an entry/exit door will flash if the system has a low battery... of this manual for further instructions. STAY LIGHT
The stay light is armed. Any time the instant icon is "on " if the zone has been bypassed. The power icon will produce...
User's Manual - Page 13
... building. Trouble conditions are: Tamper Hardware
Low Battery
Loss of Supervision
(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid "flashing" light for a short period of the exit delay as a warning to the user that zone can be violated without affecting the ready icon. • The security system will not arm if the not...
User's Manual - Page 14
...zone(s) may be unprotected and can be on or flashing. • If the power icon is on or flashing when all interior zones will illuminate, alerting the user that all interior zones are bypassed, a sensor in that zone...protected zones and
sensors are bypassed. If "Auto Instant" is inside the premise and wants protection around the perimeter.
If any zone(s) are secure. ...
User's Manual - Page 15
...you enter a valid code. If a valid code is used if it is flashing during the entry delay, the alarm system has been activated in the STAY mode...Quick Arm feature may restore an entry delay by pressing the [STAY] key. The security system is ideal for the duration of the entry delay, an alarm will occur.... interior zones. (Optional) When armed, pressing the [EXIT] key will stop.
User's Manual - Page 16
... 1 Step 2 Step 3
Step 4 Step 5
Step 6
Press the [BYPASS] key.
Page 16
NX1448E Icon Keypad Press the [BYPASS] key again -or-
The bypass light flashes. The corresponding zone icon will stay on . GROUP BYPASS
By pressing the [BYPASS] key, followed by the [CANCEL] key while this must be bypassed. The following steps are...
User's Manual - Page 17
... for user 3.)
The instant icon will flash and zone icons will illuminate specifying the first digit of...zones will automatically be unbypassed each time the system is on the chime light will be off.
NX1448E Icon Keypad
Page 17
The Ready icon will flash. Enter a ["Master Arm/Disarm" Code].
UNBYPASSING To manually unbypass zones, perform the bypassing procedure on a zone that zone...
User's Manual - Page 19
...press numbers corresponding to areas where you to give the user access or deny access. (Example: If zone icon #2 is lit, then the user is programmed as a function code.
Do not change! This... Arm Only Arm Only After Closing Time Master Arm/Disarm (can program other codes) Arm/Disarm Bypass Zones Open / Close Reporting If this code is assigned access to the following chart. By pressing the ...
User's Manual - Page 21
... Disarmed to silence the siren.
Step 1 Step 2
Press [r]-[4].
SET SYSTEM DATE
Step 1 Press [r]-[9]-[6]. Enter Code icon will perform a battery test, communicator test, and/or a siren test. Step 2
The ALARM MEMORY feature will flash those zones that were bypassed during the last alarm. If the siren test is performed at which time a test signal...
User's Manual - Page 23
... Press [r]-[9]-[1]. It is tampered, the tamper icon will flash and the zone icon(s) will be "on . ICON 1
2
PROBLEM
SYSTEM FAULT -
If a zone(s) is usually easier to the system fault(s) below:
1 Over Current Fault 2 Siren Trouble 3 Box Tamper
5 Expander Low Battery 6 Expander Box Tamper 7 Expander Trouble
4 Expander Power
8 Ground Fault
Note: Faults 1 & 2 are global in a darkened...
User's Manual - Page 24
... a low battery. Press the [6] key. The
zone icon(s) will illuminate when there
has been a loss of a multi-partition system. Press the [#] key to exit the Service Menu.
* NOTE to wireless zones. The zone icon(s) will affect all partitions of power and your system and the
central station. * SEE NOTE AT END OF TABLE.
8
LOSS OF SYSTEM...
User's Manual - Page 25
If programmed, your system keypad may sound for any zone(s) are detected: Zone or Box Tamper, Low Battery, AC Power Fail, or Expander trouble.
Beeps for 1 second or emits a "ding-dong" sound for the last 10 seconds of the following conditions are bypassed.
Pulses when a day zone is violated while the system is detected. beeps rapidly for...
Similar Questions
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)
My Nx-148e Alarm 'beeps' Every Minute. A Message 'low Battery' Appears
I have lived here for over two years & first time I have had this problem.
I have lived here for over two years & first time I have had this problem.
(Posted by struthbur 12 years ago)
Battery Location For Nx-1448e
Power on keypad is flashing. Manual says to change the battery...WHERE IS THE BATTERY??
Power on keypad is flashing. Manual says to change the battery...WHERE IS THE BATTERY??
(Posted by gg 12 years ago)
Spare Parts For Nx-1448e
Can I purchase the back plate for the NX-1448E? Please advise - Thank you
Can I purchase the back plate for the NX-1448E? Please advise - Thank you
(Posted by yap40j 12 years ago)
'power' Is Flashing..manual States Power Is Low..where Is Battery?
(Posted by beckyhudson 14 years ago)