Harbor Freight Tools 61932 Support Question
Harbor Freight Tools 61932 Support Question
Find answers below for this question about Harbor Freight Tools 61932 - Cement Mixer - 3-1/2 Cubic Ft.Need a Harbor Freight Tools 61932 manual? We have 1 online manual for this item!
Question posted by djholmes0928 on April 25th, 2023
Sheer Pin On The Cement Mixer?
If there is one, where is this located?
Current Answers
Answer #1: Posted by SonuKumar on April 25th, 2023 10:27 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,653,150
Member since:
May 9th, 2021 Points: 16,653,150
The Harbor Freight Tools 61932 cement mixer uses a sheer pin to protect the motor from damage in case the drum becomes jammed or overloaded. If the mixer suddenly stops during use, it is possible that the sheer pin has broken and needs to be replaced.
To replace the sheer pin on the Harbor Freight Tools 61932 cement mixer, you can follow these steps:
- Unplug the mixer and remove the drum from the frame.
- Locate the sheer pin on the motor shaft.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Harbor Freight Tools 61932 Manual Pages
User Manual - Page 2
... safety alert symbol.
Indicates a hazardous situation which , if not avoided, could result in death or serious injury.
Item 61932
Setup
Operation
Maintenance
Page 2
For technical questions, please call 1-888-866-5797. Safety
NOTICE
FOR CEMENT AND MORTAR ONLY. Table of Contents
Safetye 3 Specifications 6 Setup 7 Operationa 10
Maintenancei 12 Parts List and Diagram...
User Manual - Page 3
... RISK OF UNINTENTIONAL STARTING. NEVER LEAVE TOOL RUNNING UNATTENDED. Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Assemble only according to do not use power tools in electric shock, fire and/or serious injury. Sudden load movement may result in damp or wet locations, or expose them to hold work...
User Manual - Page 4
...tool...tools require a three wire extension cord. Double Insulated tools... tool...CEMENT AND MORTAR ONLY.
Do not use either a two or three wire extension cord.
2. If the tool should look like those in loss of power and possible tool...plug. Tools marked with...use with the tool. Always replace ...tool. As the distance from ...Tools: Tools with all codes and ordinances. The tool... one tool, add...
User Manual - Page 5
...(s) before turning on the tool.
Prepare to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.)
9. Operation
Maintenance
Item 61932
For technical questions, please call...dust masks that may not provide adequate protection. It is unsafe to move the Cement Mixer when it is full and/or in close proximity to cause cancer, birth defects...
User Manual - Page 6
...61932 Include vibration-free periods each day of vibration-related injury:
1. Specifications
Electrical Input Motor No Load Speed Drum Speed Drum Capacity Drum Opening
120 VAC / 60 Hz / 3.5 A 1820 RPM 36 RPM 3-1/2 Cubic....
5. To reduce vibration, maintain the tool as possible.
2. Do not use .
Safety
Vibration Safety
NOTICE
FOR CEMENT AND MORTAR ONLY. Pregnant women or people...
User Manual - Page 7
...in the following pages, refer to the Assembly Diagram near the end of the tool off before set up or use with Epoxy 2-part resin mix. Fasten together...that bolt holes line up .
4.
Page 7
Cotter Pin (1)
Figure C
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY. See Figure A.
Fasten together using ...
User Manual - Page 8
...
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY....Support Bracket Seat (35) using Hex Bolts (28), Spring Washers (29) and Flat Washers (30). Item 61932 Lower Drum (48)
16. Control Handle (46)
Arm (77) Hex Nut (44) Coil Spring (...Nuts (5). Fasten together using Flat Washers (58) and Nuts (32).
17. Position each of Mixer Blades to Lower Drum using Hex Bolts (54), Washers (55), Seal Gaskets (56), and...
User Manual - Page 9
... on the side of lubricating oil on the Pinion Shaft. Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Clean the Pinion Shaft (36...Drum Pulley. When proper V-Belt tension is pushed in place. Page 9
Adjust Motor location as needed.
29.
The Pulley should be adjusted forward or backward later.
26....
NOTICE
FOR CEMENT AND MORTAR ONLY.
User Manual - Page 10
Item 61932 Safety
NOTICE
FOR CEMENT AND MORTAR ONLY.
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this product. Functions
Motor Assembly Mixer Blade
Upper Drum
Control Handle
Stand Wheel Bracket
Wheel
Lower Drum Arm
Leg
Handle Control
Plate
Setup
Operation
Maintenance
Page 10
For technical questions, please ...
User Manual - Page 11
.... Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. WARNING! Adjust the Drum angle by pulling the Control Handle away from Drum.
9. Do not turn Mixer off while full of cement and 15 shovels aggregate rock (using a size 3 shovel, not included).
4. Re-engage the locking pins.
5. General Operating Instructions
1.
CAUTION...
User Manual - Page 12
...out all fasteners and other damage.
Retighten V-Belt after the first 25 hours of the tool.
Tighten the Motor Bracket bolts.
4.
If the belt is too long to 3/4". Tighten... Cement Mixer. d. b. If the belt deflects too little, loosen the Motor Bracket bolts and lift Bracket upward. Item 61932 Safety
Setup
NOTICE
FOR CEMENT AND MORTAR ONLY. TO PREVENT SERIOUS INJURY FROM TOOL ...
User Manual - Page 13
...tool. Setup
Operation
Maintenance
Item 61932
For technical questions, please call 1-888-866-5797. Do not use one with Epoxy 2-part resin mix.
Running at outlet. If breaker is unpowered, turn
off tool..., use with the proper diameter for the tool and circuit has no -load intervals.
2.
Safety
Troubleshooting
NOTICE
FOR CEMENT AND MORTAR ONLY. Motor being strained by ...
User Manual - Page 14
...Setup
NOTICE
FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix.
Parts List and Diagram
Parts List
Part
Description
1 Cotter Pin 5×40
...
60 Rubber Gasket
61 Hex Bolt M8×20
62 Mixer Blade
63 Rubber Gasket
64 Flat Key 5×25
65...1 1 1 1 2 4 2 1 2 1 1 1 1 1 1
Operation
Maintenance
Page 14
For technical questions, please call 1-888-866-5797.
Item 61932
User Manual - Page 15
...:
Note: If product has no serial number, record month and year of purchase instead.
Page 15
Do not use with Epoxy 2-part resin mix. Item 61932
For technical questions, please call 1-888-866-5797. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as...
User Manual - Page 16
... other rights which vary from the date of our product. Limited 90 Day Warranty
Harbor Freight Tools Co. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ... AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. Proof of purchase date and an explanation of the complaint must be liable for incidental,...
Similar Questions
On Off Switch
where can I get the on off switch for my cement mixer #61931
where can I get the on off switch for my cement mixer #61931
(Posted by Starlifter77 1 year ago)
Bolts For Mixer?
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
I'm missing some bolts/screws for 31/2 cubic foot cement mixer. How do I get a complete set of bolts...
(Posted by chrstphr1grffn 2 years ago)
Handle Control Plate
Just bought a Central machinery Cement Mixer Item 61932. Bought it off e-bay and it is missing a par...
Just bought a Central machinery Cement Mixer Item 61932. Bought it off e-bay and it is missing a par...
(Posted by mtruitt54 7 years ago)