Harbor Freight Tools 93458 Support Question
Harbor Freight Tools 93458 Support Question
Find answers below for this question about Harbor Freight Tools 93458 - 3/16 in. Air Hydraulic Riveter.Need a Harbor Freight Tools 93458 manual? We have 1 online manual for this item!
Question posted by borowskicb on November 15th, 2016
Difficulty Removing Piston Assm From Air Cylinder
Do you have any hints as to how to properly remove Piston Assm to initially prime unit. Pg 10 of instructions " Use pair of pliers to remove Piston Assm (30-33) from Air Cylinder (29). No Go , even with vice grips.Should i initiate unit ti "free up O-ring? any other ideas?
Current Answers
Answer #1: Posted by waelsaidani1 on January 23rd, 2017 1:56 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,777
Member since:
May 12th, 2013 Points: 19,501,777
Use the Spanner (36) to unscrew and remove the Cylinder Cap (33) from the bottom of the Riveter. 2. Use a pair of pliers (not included) to remove the Piston Assembly (30 thru 33) from the Air Cylinder (29). 3. Hold the Air Cylinder (29) upside down, and pour in hydraulic oil (not included). The fill level should only reach the top of the Frame (15). 4. Insert the Piston Assembly (30 thru 33) back into the Air Cylinder (29). 5. Use the Spanner (36) to firmly screw the Cylinder Cap (33) back onto the Air Cylinder (29).
Related Harbor Freight Tools 93458 Manual Pages
User Manual - Page 1
... before using this manual or any artwork contained herein may not be drawn proportionally. No portion of Harbor Freight Tools. Diagrams within this manual.
Tools required ...the express written consent of this product. AIR HYDRAULIC RIVETER
Model 93458
Set up And Operating Instructions
Distributed exclusively by Harbor Freight Tools®. Failure to continuing improvements, actual ...
User Manual - Page 2
... invoice number on the cover of this manual. Keep work area well lit. Use the right tool for which this Riveter. PRODUCT SPECIFICATIONS
Rivet Capacity Operating Air Pressure Air Consumption Air Inlet Size Nosepiece Sizes
3/32", 1/8", 5/32", & 3/16" sized pins 90 PSI 4.5 CFM @ 90 PSI 1/4"-18 NPT 3/32", 1/8", 5/32", 3/16"
SAVE THIS MANUAL
You will do the work area.
User Manual - Page 3
... and perform its intended function. Before using any tool, any other condition that may affect proper operation. If there is attached to an air source.
12. Disconnect the Riveter when not in . Approved accessories are removed from Harbor Freight Tools.
16. Check that it will void the warranty. Use of alcohol or drugs. Remove adjusting wrenches. Watch what you are...
User Manual - Page 4
..., and is designed for soft surfaces.
20. Transport the Riveter safely. Carry the tool by the operator that may split the workpiece and cause it to avoid spilling used Rivet Pins.
24. This Riveter is not suitable for use . The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that common...
User Manual - Page 5
... available at Harbor Freight Tools. Note: If an automatic oiler is properly seated in the tool's quick connector before each use , the Riveter requires the attachment of the Quick Connector. Prior to use .
2. To do so, make sure the screen Air Filter is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the Air Cylinder.
ASSEMBLY INSTRUCTIONS
1.
Wrap approximately 3" of...
User Manual - Page 6
... the Air Cylinder (29). (See Figure C.)
5. Use a pair of pliers (not included) to firmly screw the Cylinder Cap (33) back onto the Air Cylinder (29). (See Figure C.)
SKU 93458 For technical questions, please call 1-800-444-3353
REV 05i
PAGE 6 The fill level should only reach the top of the Riveter. (See Figure C.)
2. Use the Spanner (36) to remove the Piston Assembly (30 thru 33) from...
User Manual - Page 7
... (23) firmly to remove the old nosepiece and install the new one. Depending on the air compressor, and set its regulator at 90 PSI. IMPORTANT: When drilling rivet holes in a workpiece, use . (See Figure D.)
OPERATING INSTRUCTIONS
1. Do not exceed 90
PSI. Attach an air hose to avoid spilling used , attach the corresponding Nosepiece size (3/16", 5/32", 1/8", or 3/32...
User Manual - Page 8
... time,
SKU 93458 For technical questions, please call 1-800-444-3353
PAGE 8 INSPECTION, MAINTENANCE, AND CLEANING
WARNING! Then, store the Riveter in liquids.
2. WARNING! Use the Spanner (36) to release any inspection, maintenance, or cleaning of children. Remove the Jaws (7) from the tool. Wear ANSI-approved safety impact goggles when performing any compressed air in the...
User Manual - Page 9
...the Jaw Cases until the distance is corrected. (See Figure E.)
h. Store the Riveter in between the Jaws, pushing them slightly apart.
With the gauge at a slight...Frame Head (11) using the Spanner Gauge (35).
3. Before reassembly, secure the Lock Nut (12) against the Jaw Case assembly using the gauge on ...
SKU 93458 For technical questions, please call 1-800-444-3353
REV 08i
PAGE 9
User Manual - Page 10
...
SKU 93458 For technical questions, please call 1-800-444-3353
PAGE 10 TROUBLESHOOTING
Problem
Jaws slipping. Stroke is too short.
Rivet wrong size. 1. Reconnect using pipe thread seal tape.
2. Clean Jaws.
1. Low air pressure.
3. Likely Solution
Replace Jaws. 1. Use proper rivet length. 1. Broken/inadequate air compressor.
2. Clean and lubricate with pneumatic tool oil...
User Manual - Page 11
... DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. SKU 93458 For technical questions, please call 1-800-444-3353
PAGE 11
1A
11
ASSEMBLY DIAGRAM
6-1 7
8 10A 20 24 23
22
6-2 10 9 12141314
37
40 43A
39
30-1
44
41
29
30-4
30-2
31A
44A
43A 45B
30-5
45
30-3
44
32
51
33
52
15 16 38
23 26 25
1718
19...
User Manual - Page 12
...6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 93458 For technical questions, please call 1-800-444-3353
PAGE 12 This warranty ...or property, or for the period of 90 days from the use of maintenance. To take advantage of purchase. If our inspection...us with a replacement. 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality...
Similar Questions
I Need An Unloader Tube For Air Compressor Serial #61693
I need an unloader tube for a central pneumatic air compressor serial number 61693
I need an unloader tube for a central pneumatic air compressor serial number 61693
(Posted by josephelliscox 1 year ago)
Air Bubble Water Pump
how to remove a air pocket in a pacific hydrostatic 62508 110lif
how to remove a air pocket in a pacific hydrostatic 62508 110lif
(Posted by jburleson1070 2 years ago)
I Need The Copper Pipe That Goes From Compressor To Air Tank... Item 69783. Seri
i need the copper pipe that goes from compressor to air tank itwm 69783. wheel barrow type compresso...
i need the copper pipe that goes from compressor to air tank itwm 69783. wheel barrow type compresso...
(Posted by stonyridgetigerman 2 years ago)
Stapler Does Not Appear To Charge With Air. Trigger Cylinder Has No Resistance
I bought the unit yesterday and went thought the instructions, made connection to air supply (140psi...
I bought the unit yesterday and went thought the instructions, made connection to air supply (140psi...
(Posted by kd092 8 years ago)