Hayward E-Command 4 Support Question
Hayward E-Command 4 Support Question
Find answers below for this question about Hayward E-Command 4.Need a Hayward E-Command 4 manual? We have 2 online manuals for this item!
Question posted by anderkin4 on January 29th, 2014
E-command 4 Control Of Ecostar 2 Stage Pump
diagram provided doesn't show control wiring between command module and pump, just that they are connected. need correspondence between command and pump pin outs
Current Answers
Related Hayward E-Command 4 Manual Pages
Model: ALL MODELS Installation - Page 7
... enabled for the filter, valves or aux
outputs or if the chlorinator is in the "pool only" operating mode.
6.
2. Plumbing
Pool/Spa system configuration
These systems use a single filter pump and filter. If the chlorinator cell is controlled by two 3-way valves
(suction and return). The air sensor must be installed prior to the diagram below.
Model: ALL MODELS Installation - Page 10
... are rated at 3HP/30A at 240V (1½HP/30A at 120V). High Voltage (120/240V) Pool Equipment
All ECOMMAND 4 relays are double pole (they make/break both "legs" of the AUX relays) for high voltage pool/spa lighting.
Refer to the diagram below AND to configure
the control logic according to control an automatic pool cover.
Model: ALL MODELS Installation - Page 11
... VSC. Hayward Variable Speed Filter Pump: Proper installation of the valve outputs are dedicated to the pool/spa suction (Valve2) and return (Valve1) valves. The Filter relay is off (power off . Refer to an external control (usually identified as "2-wire" remote control). Refer to the following diagram for connecting the heater to the diagram on the following pages for...
Model: ALL MODELS Installation - Page 15
... setting the pump address. The maximum wiring distance is required, contact the Goldline service dept.
Refer to "2", etc. The sensors are included. If a longer cable is 500 feet (160 meters). Temperature Sensors The ECOMMAND 4 utilizes 10K ohm thermistor type sensors. cable. POOL/SPA SENSOR
AIR SENSOR
SOLAR/SPA SENSOR
Pool/Spa Air Solar
12 The terminal connections should...
Model: ALL MODELS Installation - Page 19
When disabled (default), the return and suction pool/spa valves function normally. Std".
When the filter pump output is controlled by commands sent to the pump. On , off and speed is off, the relay will be configured to control the low speed motor winding on the pump. It is set to "Pool and Spa - Set lowest speed from 10% (default) to...
Model: ALL MODELS Installation - Page 21
...pool. If solar is "Enabled", the valve or solar pump relay will turn on , it will operate normally.
18 Allow Low Speed This menu only appears if the filter is hotter than the water. This provides...Control" and "Heater Control" are enabled, the Solar Priority feature will turn off whenever solar heat is available. Solar Priority If both the solar valve/pump and filter pump... pool and spa ...
Model: ALL MODELS Installation - Page 23
... panels to prime and get water flowing), when the pool/spa suction return valves are the same as shown below the...
When "Dimmer" is selected, and the Lights output is wired to 100% (default). If an alternate speed is desired ...pump is set to on . Lights Interlock If enabled, this only enables operation of filter pump operation (allows the pump to be assigned to control an automatic pool...
Model: ALL MODELS Installation - Page 24
... between turning on and off , first 3 minutes of filter pump operation (allows the pump to prime and get water flowing), when the pool/spa suction return valves are the Settings Menu speed and a speed... -
Solar - menu for proper operation. if "Chlorinator" is desired. Note that "Solar Control" must be enabled in the "Solar Config." The optional AQL-DIM dimmer kit must be installed...
Model: ALL MODELS Installation - Page 27
... to the heater control (see "Heater Control" wiring, page 8). • Some heaters also have internal switches or jumpers that the following : • The heater is enabled (Configuration Menu/Heater Config.). • The heater temperature setting is at least 2ºF greater than the water temperature (Settings Menu / Pool Heater & Spa Heater). • The filter pump is running...
Model: ALL MODELS Installation - Page 32
... setting
salt level reason pump is running (not scheduled) reason hi-speed is running (not scheduled)
countdown time remaining heater control status system manual off check system error filter speed
spa heater1 temperature pool heater1 temperature
spa solar temperature pool solar temperature
superchlorinate spa chlorinator setting pool chlorinator setting
spa high/low speed pool high/low speed
day...
Model: ALL MODELS Operation - Page 4
...
Water
Temperature Sensors
Air
Solar
Filter Pump Lights Aux 1
120/240V Relays
Aux 2
Pool/Spa Suction & Return Valves
Valve 3
24V Valve Actuators
Heater
240 VAC Power
Circuit Breaker Subpanel
NOTE: This manual assumes that pertain to the Installation Manual. Automation
The ECOMMAND 4 can control up to fully manage your pool/spa system. All of equipment, up...
Model: ALL MODELS Operation - Page 5
... turn on high speed operation of your pool/spa system, there may be certain times when you want to override the heater cooldown, simply press the FILTER button again to override the automatic operation and control the equipment manually.
Two Speed or Variable Speed Filter Pump: If the pump is enabled (Configuration Menu) then: when...
Model: ALL MODELS Operation - Page 6
... modes.
3 If the controlled output is enabled and the AIR temperature sensor falls below the preset freeze protection temperature (see Filter Configuration), the ECOMMAND 4 will turn off while the pool/spa valves are turning. Note that the ECOMMAND 4 will automatically return to normal operation after 3 hours. Assuming that the filter pump will turn off...
Model: ALL MODELS Operation - Page 8
... setting
salt level reason pump is running (not scheduled) reason hi-speed is running (not scheduled)
countdown time remaining heater control status system manual off check system error filter speed
spa heater1 temperature pool heater1 temperature
spa solar temperature pool solar temperature
superchlorinate spa chlorinator setting pool chlorinator setting
spa high/low speed pool high/low speed
day...
Model: ALL MODELS Operation - Page 9
...to previous/next menu item
The spa heater setting will only appear if the system has been setup for "spa only" or "pool and spa" operation and the heater control is primarily intended for 2 ... menu item
The pool heater setting will turn on whenever the pool/spa valves are in the "spa only" position and the filter pump is running and the spa water temperature is connected to the default menu...
Model: ALL MODELS Operation - Page 10
... been setup for "pool only" or "pool and spa" operation and the solar control is running due to "Highest Speed" in spa-only mode.
The actual amount of chlorine introduced into the pool is determined by this setting, the amount of time the filter pump is enabled. If the filter pump is running and the pool water temperature is...
Model: ALL MODELS Operation - Page 13
... will be manually controlled. There is the second filter timeclock
10 These include super-chlorination, spa operation, manual operation, heater cooldown, freeze protection and "solar-extend". All of filtration for general notes regarding timeclock programming. If "weekends/weekdays" are several reasons the filter pump may be the period of your pool/spa system. The Countdown...
Model: ALL MODELS Operation - Page 14
... the lights until the ECOMMAND 4 automatically turns off prior to the start and stop times & to high speed operation during the programmed off control
by pressing the LIGHTS button. Refer to low speed for "pool and spa". You can also manually turn on the filter pump and move the pool/spa valves into the "spa-only" position.
Model: ALL MODELS Operation - Page 17
... to previous/next configuration menu
Filter Pump For 2-speed pumps: When a 2-speed pump is turned on the pump. When disabled (default), the return and suction pool/spa valves function normally. Filter Off Valve Change This menu appears only if Pool/Spa setup is "Pool Only" or "Spa Only". The pump will switch the pool/spa valves to control the low speed motor winding on...
Model: ALL MODELS Operation - Page 18
... operation anytime the pump has been off and speed is controlled by commands sent to 100% (default). For the Hayward Tristar variable speed pump: The Filter relay is used to supply input power to protect the pool and plumbed equipment against freeze damage. It is used as the upper limit in the Pool/Spa sub-menu, the...
Similar Questions
My Hayward E Command 4 Will Not Turn On My Pump Automatically Or Manually.
When trying to turn on my pump manually it just goes into check system
When trying to turn on my pump manually it just goes into check system
(Posted by cardenasj68 2 years ago)
I Recently Lost Power, Now My Ecommand 4 Panel Will Not Turn My Pump On.
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
(Posted by karenmonroelvnv 9 years ago)
Connecting A Pro Logic Ps-4 Controller To An Ecostar By Hayward Pump
I have tried numerous wiring combination and i still can not get the pump to work with the controlle...
I have tried numerous wiring combination and i still can not get the pump to work with the controlle...
(Posted by stephengehrmann 11 years ago)
What Settings Should I Use For The Ecostar Above Ground Pump? I Have A 30k Pool?
(Posted by anita92252 12 years ago)