Hoover U5753 Support Question
Hoover U5753 Support Question
Find answers below for this question about Hoover U5753.Need a Hoover U5753 manual? We have 1 online manual for this item!
Question posted by taschajasper on November 12th, 2011
No Suction In Power Head
hoover 5753-955 Wind Tunnel.
no suction in our power head. The hand nozzle has good suction. Belt is clean and turning, all debris has been taken out. Checked flap inside nozzel it opens when unit is tilted in the working position. All filters are clean.
Current Answers
Related Hoover U5753 Manual Pages
Manual - Page 1
www.hoover.com
®
This product was designed for easy assembly (see page 3)
WindTunnel™
Bagless by HOOVER
Congratulations on your purchase!
Manual - Page 2
...Cleaning filters 8-9 Emptying Dirt Cup 8 Replacing Agitator Brush Roll ......11 Replacing Power Hand Tool
Agitator Brush Roll 12 Replacing Belt 10-11 Replacing Power Hand Tool Belt ..12 Replacing Edge Groomers 11 Replacing Headlight 10 Thermal Protector 13 Warranty 14
© 2004 The Hoover Company
www.hoover...openings. Save these instructions!
2 If appliance is not working ...
Manual - Page 3
... should happen to need assistance during assembly or operation, call:
Visit us on-line at www.hoover.com to speak with a representative in the assembly of your cleaner.
Handle section B. Assembly can...you (click on cleaner) D. Hose, cleaning tools and wands (packed on the "Service" button) OR 1-800-944-9200 for an automated referral of packing. Powered hand tool (some models)
Note: The ...
Manual - Page 4
... screwdriver. Dispose of handle. If switch lock has come off during assembly, make sure switch is in OFF position (down) before plugging into holes on cleaner body (B). Remove powered hand tool (some models) from handle section. Open tool cover on back of switch lock.
Push screws into electrical outlet.
4
Remove switch lock (C) above ON...
Manual - Page 5
...; Polarized plug
To reduce the risk of carpet being cleaned.
16. Carrying cleaner
The cleaner can be moved by using cleaning tools; operating position for storage and when using the carrying handle. Handle
2. Powered hand tool* or Crevice tool*
19. Final filter
23. Extension wands
26. To turn cleaner ON, push switch up. 2. Pre-filter 13...
Manual - Page 6
... come on when the cleaner is first turned on throughout cleaning, except when the detector senses that a...nozzle so that when you should take additional cleaning strokes in the upright position and tilt cleaner foward (E). Cleaning lightweight flexible rugs
Stand on for various carpet pile heights, slide the nozzle control knob (D) to the desired setting.
2-7
2-8
2-9
F E
Handle position...
Manual - Page 7
... reaching hard to prevent the cleaner from cleaner. Clean from bottom to OFF position.
How to clean tools
To clean the hose and the powered hand tool, wipe off dirt with any of tool storage area. Guide either side of nozzle parallel to edge of the nozzle to remove dirt in such places as dresser drawers, upholstered furniture...
Manual - Page 8
... will collect fine particles that the dirt cup be emptied before the dirt reaches the dirt inlet opening on back of cup until no more dust particles fall from cleaner.
3-3
Remove lid. Push ... This larger debris will rest behind grooves at bottom of suction. Bottom of cup will be removed for this type of cup.
8 Lift cup slightly and pull straight out to clean filter assembly
Remove...
Manual - Page 9
...to ensure that it becomes dirty, open too far. Cleaning secondary filter
Disconnect cleaner from assembly. Remove screw and pull grill out. Hand wash filter in cold water with mild... filter, grill and screw.
Allow pre-filter to replace this filter, ask for HOOVER part No. 38762008.
3-13
L
Cleaning final filter
The final filter assists in place.
Tap filter until a light snap ...
Manual - Page 10
... genuine HOOVER belts with your cleaner's excellent pick up and suction. When to replace
Disconnect cleaner from electrical outlet. When purchasing a new belt, ask for the effective operation of the cleaner and should be checked from time to time to be sure it is not required. Check for debris accumulation under the agitator shield each time you clean...
Manual - Page 11
... of the nozzle, should be replaced when they appear worn. How to reposition belt, new agitator and bottom plate.
What to buy
When purchasing a new agitator, ask for HOOVER part No. 39511004.
Turn agitator making sure belt is not pinched between agitator and agitator shield.
3-22
Replacing bottom plate Reposition bottom plate and 4 Phillips head screws...
Manual - Page 12
... (E) on either side of bottom plate into place. 5. Powered hand tool
Belt replacement Inspecting the belt
The powered hand tool belt is designed to last a long time and is in Figs. 3-25 through belt and position belt over gear teeth (D) on edge of tool and remove bottom plate (A).
3-28
3-29
B
3-27
D
C
3. Ask for HOOVER part No. 38528037. 1. Unscrew the two Phillips...
Manual - Page 13
... dirt cup.
Problem: Dirt inside dirt cup stops spinning Note: Heavy debris may need servicing (see pg. 13). Problem: Powered hand tool (some models) brush roll won 't pick up
Possible cause Possible solution
• Broken or worn belt • Replace belt
• Agitator brush roll worn • Replace brush roll
• Dirt cup full • Empty...
Manual - Page 14
..., The Hoover Company, 101 East Maple St., North Canton, Ohio 44720. Phone 330-499-9499. Check fullness of purchase will be obtained by a limited one way. Clear blockage from hose. Disconnect powered hand tool from dirt duct sections.
4-2
C
Checking under "Cleaner suction
low". • Broken or worn belt • Replace belt • Low cleaner suction • Check items under...
Manual - Page 36
HOOVER y
®son marcas registradas
HOOVER et
®sont des marques déposées
HOOVER and
® are registered trademarks
3-04 U5753-/65-/67-/69-900
Printed in Mexico
56511-C19
Similar Questions
Vacuum Does Not Turn On I Checked For Blocks Everything Is Clear
(Posted by Jabrialiya 4 years ago)
Power Cord Won't Retract On Hoover Wind Tunnel Series Vacuum
(Posted by dintho 9 years ago)
Hoover Wind Tunnel Vacuum Wont Turn On
(Posted by FlaFerr 10 years ago)
Wind Tunnel Why Would There Be Lack Of Suction?
My wind tunnel filter wont spin. I got a new one same problem .No suction. What is the possible prob...
My wind tunnel filter wont spin. I got a new one same problem .No suction. What is the possible prob...
(Posted by cmcgilvary 10 years ago)
Power Switch
How do you replace the power switch. The new switch we received for this model has two black wires a...
How do you replace the power switch. The new switch we received for this model has two black wires a...
(Posted by djweeks 10 years ago)