Husqvarna 440 Support Question
Husqvarna 440 Support Question
Find answers below for this question about Husqvarna 440.Need a Husqvarna 440 manual? We have 1 online manual for this item!
Question posted by angiegdma61 on January 29th, 2015
Start Problems
motor starts cold-- misses at high rpm--dies--will not restart
Current Answers
Answer #1: Posted by waelsaidani1 on January 29th, 2015 8:36 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,777
Member since:
May 12th, 2013 Points: 19,501,777
Related Husqvarna 440 Manual Pages
Operation Manual - Page 2
...and towards the operator.
English
115 10 82-26 Rev.2 2008-06-03
The start/stop switch automatically returns to the European Community's Directive.
Noise emission to the ... protective helmet • Approved hearing protection • Protective goggles or a visor
This product is started. The machine's emission is required. The chain brake must be used to the operator or others...
Operation Manual - Page 3
... equipment 7 Machine′s safety equipment 7 Cutting equipment 11 ASSEMBLY Fitting the bar and chain 17 FUEL HANDLING Fuel 19 Fuelling 20 Fuel safety 20 STARTING AND STOPPING Starting and stopping 21 WORKING TECHNIQUES Before use 23 General working instructions 23 How to avoid kickback 30 MAINTENANCE General 31 Carburettor adjustment 31 Checking...
Operation Manual - Page 4
..., sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers appeared, followed by chain saws in 1959, and it will appreciate with...product development and therefore reserves the right to develop, manufacture and market motor driven products for forestry and gardening as well as our highest priority.
INTRODUCTION
Dear Customer,
Congratulations on the...
Operation Manual - Page 5
What is what on the chain saw? 1 Cylinder cover 2 Air purge 3 Start reminder 4 Combined start and stop switch 5 Rear handle 6 Information and warning decal 7 Fuel tank 8 Adjuster screws carburettor 9 Starter handle 10 Starter 11 Chain oil tank 12 Product and ...
Operation Manual - Page 6
... of a damaged
muffler.
Always wear protective glasses or a face visor to start the chain saw is a dangerous
!
WARNING! Faulty cutting equipment or
!
See
instructions ..., chain oil mist
and dust from thrown objects. Never allow children to noise can be started
by trained and qualified specialists.
See instructions under the heading
Technical data.
6...
Operation Manual - Page 8
... the chain saw in the kickback direction.
• Use the chain brake as a "parking brake" when starting and when moving the front hand guard marked "PULL BACK TO RESET" back, towards the front handle.
•... of the chain saw firmly and not let go.
• The front hand guard is started to prevent the saw can become very hot.
• The chain brake (A) can be activated by...
Operation Manual - Page 10
...;er
The muffler is insulated from the user. Never start a fire. In areas with a hot, dry climate ... of overexposure
to minimize vibration and make sure that is a high risk of spark arrestor mesh. Be aware of vibration between the... without or with cutting equipment that the mesh is
required in cold
temperatures. CAUTION! WARNING! muffler, or with an approved...
Operation Manual - Page 19
.... This gives rise to a high engine temperature and increased bearing load, which is obtained. Add the remaining amount of fuel at a too high speed for fuel.
• Always start by filling half the amount... results in
Avoid running at a time.
• If the machine is equipped with continuous high revs (e.g. It is important to accurately measure the amount of oil to be mixed to ensure...
Operation Manual - Page 20
...highly flammable. Wash any part of the chain saw and fuel so that any hot objects in an approved container designed for that purpose.
• For longer periods of storage or for a few minutes before starting... plug guard
and ignition cable. Check regularly for leaks from electrical equipment, electric motors, relays/switches, boilers and the like.
• Always store fuel in the...
Operation Manual - Page 21
...Disengagement is heated restart the saw is done by gently touching on firm ground.
Air purge (2): Press the air purge diaphragm repeatedly until the engine starts (5). Do not ... mist
and dust from the working area. Starting
The chain brake must be heard through the rear handle.
Cold engine
Start position (1): Set the start/stop switch in the choke position by pushing...
Operation Manual - Page 22
... handles.
• The chain brake is unsupervised.
• Never start a chain saw the clutch can be activated when starting.
The start /stop switch automatically returns to the chain saw unless the bar, ... and cause serious injury. Use a firm grip with both hands. To avoid involuntary start up, the spark plug cap must always be on the rear handle, and the left handed...
Operation Manual - Page 25
... saw pulls itself towards the tree and the front edge of the bar, i.e. Terms
Cutting = General term for too long at you can avoid these problems by cutting in tension.
In this pushing force there is a risk that the chain saw will move about?
Never use only combinations that it is...
Operation Manual - Page 26
...situations you are lying together.
Cut difficult branches piece by cutting from the opposite side. Start by piece.
12
3
Turn the log and finish the cut .
There is a ...?) stop cutting about 1/3 of !
If it will jam.
Remove the cut individually. There is a high risk that the two cuts meet .
There is little risk of experience to be prepared for cutting....
Operation Manual - Page 27
... tree fall (2). Several factors affect this makes it more probably that the tree will break and start to the saw !
It is very dangerous to remove a trapped tree and there is done using... to fall in the direction you have special
! Felling is high accident risk. By placing these cuts correctly you can limb and cross-cut , then you during ...
Operation Manual - Page 28
... the trunk and the angle between them is at least 1/10 of the
28 - The directional cuts should start to find out which lengths of bar are badly placed.
The line where the two cuts meet is...as it must be perfectly horizontal. This line should be 45°. Make sure the tree does not start to fall by itself or with a diameter larger than the diameter of the tree, so that the tree...
Operation Manual - Page 31
...rotate at its thinnest point. Air and fuel are adjusted during testing at which the chain starts to the engine. Correct adjustment is especially true of the checks described below the speed ... idle speed setting cannot
be carried out by an authorised service workshop.
If it may cause starting difficulties and poor acceleration. When the idle speed is set too lean it is ...
Operation Manual - Page 32
...brake trigger
Place the chain saw on a stump or other object. See the instructions under the heading Start and stop immediately.
32 - Chain catcher
Grasp the chain saw firmly, wrapping your left ...Throttle lockout
Place the chain saw, with the engine switched off, on firm ground and start it . Release the front handle and let the saw . Apply full throttle and activate the chain...
Operation Manual - Page 33
...muffler that the muffler is in poor condition.
The muffler is missing or defective. Right hand guard
MAINTENANCE Muffler
Check that the right hand guard is ... wire brush.
Never use a machine that has a faulty muffler. CAUTION! The start/stop setting.
Vibration damping system
Regularly check that is securely attached to run position. In order ...
Operation Manual - Page 35
... starter
• To fit the starter, first pull out the starter cord and place the starter in order to avoid:
• Carburettor malfunctions
• Starting problems
• Loss of air filter according to engine parts.
• Excessive fuel consumption.
• Remove the air filter after taking off the air...
Operation Manual - Page 36
...dirty air filter. The clutch drum has a needle bearing on the cylinder. 5 Cylinder cover (directs cold air over the cylinder). When lubricating, remove the clutch cover by :
• Incorrect carburettor adjustment.
&#...working temperature as low as it and check that the spark plug is in operating problems and starting difficulties. English
115 10 82-26 Rev.2 2008-06-03
If the...
Similar Questions
Why Am I Having Such A Very Hard Time Trying To Start My 440 Chainsaw.
Is there a secret? i've taken it to two different places. and they started it on the first or second...
Is there a secret? i've taken it to two different places. and they started it on the first or second...
(Posted by pandorabird 2 years ago)
580 Bfs Will Not Start.
Changed fuel filter, spark plug and cleaned air filter(s). Previously problem was it would start up ...
Changed fuel filter, spark plug and cleaned air filter(s). Previously problem was it would start up ...
(Posted by prynshall 6 years ago)
440 X-torq Saw Starts But When Engaging Gas Seems To Die Out And Seems Clutch Is
Seems when putting the throttle down the chain seems binding like a clutch tightens up and will kill...
Seems when putting the throttle down the chain seems binding like a clutch tightens up and will kill...
(Posted by Meredithclark 9 years ago)
Chain Problem
I am a female user and I'm having problems keeping the 18" chain on the bar. I purchased 2 new husqv...
I am a female user and I'm having problems keeping the 18" chain on the bar. I purchased 2 new husqv...
(Posted by grandmatt 10 years ago)