Husqvarna CRT900 Support Question
Husqvarna CRT900 Support Question
Find answers below for this question about Husqvarna CRT900.Need a Husqvarna CRT900 manual? We have 2 online manuals for this item!
Question posted by jjdunk on September 16th, 2018
Disengage Handle Not Functioning For Forward/reverse Etc.. Cable Is Fine??
my model 960930017 05 handle you squeeze to switch to forward, reverse, etc. Is not functional. The cable is however fine and moves back and forth. Help?
Current Answers
Related Husqvarna CRT900 Manual Pages
Owners Manual - Page 2
...high speeds on slippery surfaces.
• Handle fuel with care;
BECOME ALERT!!! PREPARATION
...equipment without wearing adequate outer garments.
Disengage the tines, shift into neutral before...contains chemicals known to the State of all moving parts have stopped. CAUTIONS, IMPORTANTS, AND... in the ground and propel the tiller forward. Disconnect the cord on or crossing gravel...
Owners Manual - Page 4
...
Your new tiller has been assembled at the factory with exception of those parts left hand is mentioned in the operating position (standing behind tiller handles). TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. To ensure safe and proper operation of your tiller all parts and hardware you...
Owners Manual - Page 5
... CAREFUL NOT TO STRETCH OR KINK CABLES. • While holding handle assembly, cut cable ties securing
handle assembly to aid in keeping lock in place.
• Insert second handle lock (with some resistance.
HANDLE ASSEMBLY "UP" POSITION
TIGHTEN HANDLE LOCK LEVER TO HOLD
LOOSEN HANDLE LOCK LEVER TO MOVE
Fig. 4
• Rotate handle assembly down . • Remove packing material...
Owners Manual - Page 6
... of shift lever indicator. • Insert hairpin clip through hole of clutch cable through hole in control bar bracket.
HANDLE HEIGHT
• Handle height may be adjusted to better suit operator. (See "TO ADJUST HANDLE HEIGHT" in "N" position (See Fig. 7)
• Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield.
• Rotate tiller...
Owners Manual - Page 7
...cold engine. Used to start the engine.
Learn and understand their meaning. RECOIL STARTER HANDLE -
These symbols may appear on your tiller to familiarize yourself with the location of the...
CHOKE CONTROL
SHIFT LEVER INDICATOR
THROTTLE CONTROL
DEPTH STAKE
LEVELING SHIELD
RECOIL STARTER HANDLE
Fig. 8
MEETS ANSI SAFETY REQUIREMENTS
Our tillers conform to shift transmission gears...
Owners Manual - Page 8
...ANOTHER POSITION. "B"
"LOCKED" POSITION
• Move shift lever indicator to "R" (reverse) position.
• Hold drive control bar against the handle to start engine.
SIDE SHIELD
NUT "A"
depth_stake_16
HARD TO SHIFT GEARS
• Briefly engage drive control bar and release or rock tiller forward and backward until are able to "F" (forward) position.
WHEELS ONLY/TINES STOPPED...
Owners Manual - Page 9
...HELP INSURE GOOD COLD WEATHER STARTING.
Never use gasoline near an open position. • Move choke control to choke position. • Grasp recoil starter handle with one hand and grasp
tiller handle... valve life). Purchase fuel in "F" (forward) position for transporting the tiller. For ... • Transport in "DISENGAGED" position when starting engine. Move the depth stake
down to...
Owners Manual - Page 10
... . Best digging depth is digging into, turning over, and breaking up for doing this manual). Loose, unpacked soil helps root growth.
NOTE: If engine does not start . • Move throttle control to desired running position. • Allow engine to handling your tiller are much easier if you are important for best engine performance.
Owners Manual - Page 12
... drain plug. Tighten screws securely.
Tighten oil filler plug securely each five (5) hours of continuous use
7/16 12 Pt. socket with extension.)
• Tip tiller forward to enter the engine.
• Refill engine with API service classification SG-SL. DO NOT OIL CARTRIDGE. Keep the engine free of all grass, dirt...
Owners Manual - Page 14
...• Remove wheel and tire.
• Repair tire and reassemble. CLEVIS PIN
HANDLE (LOW POSITION)
HANDLE (HIGH POSITION)
HANDLE LOCK LEVER
TIRE CARE
Fig. 20
CAUTION: When mounting tires, unless beads are ... of removal, remove hairpin clip and clevis pin from unit. • Replace belt guard by reversing above procedure. HAIRPIN CLIP
Fig. 21
TO REMOVE BELT GUARD (See Fig. 22)
NOTE: For...
Owners Manual - Page 15
... BELT TO GUIDES.
• Check belt adjustment as follows:
• Loosen cable clip screw securing the drive control cable.
• Slide cable forward for less tension and rearward for more tension until about 5/8 inch stretch when drive control bar is engaged.
• Tighten cable clip screw securely.
GROUND DRIVE BELT ADJUSTMENT (See Fig. 23)
For...
Owners Manual - Page 16
..., and bending, particularly the tines which are sharp. A tine this worn needs to work harder and dig more shallow. Wear gloves or other protection when handling tines.
Owners Manual - Page 18
Inspect moving parts for 30 days or more. CYLINDER(S)
• Remove spark plug. • Pour 1 ounce (29 ml) of oil through spark plug hole into
cylinder. • Pull starter handle slowly several times to gasoline in the fuel tank or permanent.
• Use fresh fuel next season.
Do not use engine or carburetor...
Owners Manual - Page 19
... clean. 9. Make necessary adjustments. 13. Clean engine air screen. 3. Excessive bounce/ difficult handling
1. Ground too dry and hard.
1. Wait for more favorable soil conditions.
V-belt is ... air screen, and muffler area. 4. V-belt not correctly adjusted. 3. Engine runs but tiller won't move
1. Clogged fuel tank. 7. Bad spark plug or improper gap. 9. Dirty air cleaner. 3. Check ...
Owners Manual - Page 20
...Flange 1/4-20 unc 873 73 10-00 Nut, Keps #10-24 unc 532 10 41-64 Tie, Cable 532 15 06-96 Bolt, Pivot 872 14 04-04 Bolt, Carriage 1/4-20 unc x 1/2 532 10... given in U.S.
REPAIR PARTS
TILLER - - inches. 1 inch = 25.4 mm
20 MODEL NUMBER CRT900 (96093001301), PRODUCT NUMBER 960 93 00-13
HANDLE ASSEMBLY
KEY PART NO.
Owners Manual - Page 23
...Pitch 51 817 72 04-08 Screw 1/4-20 x 1/2 52 873 22 05-00 Nut, Hex 5/16-18 53 532 16 51-40 Kit, Bearing...45 Gear, Cluster, Red 1st & 2nd 40 532 10 53-46 Gear, Reverse 41 532 00 83-58 Shaft, Reduction (1st) 42 532 00 42-... 532 15 52-36 Seal Asm, Oil 48 532 18 84-85 Gearcase, R.H.
NO. MODEL NUMBER CRT900 (96093001301), PRODUCT NUMBER 960 93 00-13
TRANSMISSION
12
9
11
13 15
10
16
60...
Owners Manual - Page 28
...original OEM Husqvarna replacement parts, subject to the appropriate manufacturer or as throttle cable, belt guides adjustments.
28 All such claims must be covered separately by... not authorized to handle warranty adjustments or repairs on Exhibit A, Transmission / Transaxle (including Drive Systems) are covered by this separate warranty statement for exceptions - models equipped with the...
Parts List - Page 2
...-64 Tie, Cable 532 15 06-96 Bolt, Pivot 872 14 04-04 Bolt, Carriage 1/4-20 unc x 1/2 532 10 26-04 Grip, Bar, Control 532 10 27-44 Clamp, Bar, Control
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
20 MODEL NUMBER CRT900 (96093001301), PRODUCT NUMBER 960 93 00-13
HANDLE ASSEMBLY...
Parts List - Page 5
...51 817 72 04-08 Screw 1/4-20 x 1/2 52 873 22 05-00 Nut, Hex 5/16-18 53 532 16 51-40 Kit, ...18 85-54 Transmission Assembly (Includes Key Nos. 2-53)
2 532 18 84-82 Gearcase, L.H. MODEL NUMBER CRT900 (96093001301), PRODUCT NUMBER 960 93 00-13
TRANSMISSION
12
9
11
13 15
10
16
60 48
9...Gear, Cluster, Red 1st & 2nd 40 532 10 53-46 Gear, Reverse 41 532 00 83-58 Shaft, Reduction (1st) 42 532 00 42...
Parts List - Page 10
...any warranty obligation of purchase and beyond, such as throttle cable, belt guides adjustments.
28 All such claims must be...retail purchaser that this warranty. Limited Warranty Husqvarna warrants to handle warranty adjustments or repairs on Exhibit A. Except where otherwise...SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. models equipped with the product at our website www.husqvarna.com...
Similar Questions
Overheating Issues
3 yr old 536LiLX trimmer won't run for more than approx 1/2 a battery charge without shutting down. ...
3 yr old 536LiLX trimmer won't run for more than approx 1/2 a battery charge without shutting down. ...
(Posted by toplog 1 year ago)
Reverse/forward Shifting Linkage Parts Diagram
my lawnmower will not shift into reverse it seems to be broken
my lawnmower will not shift into reverse it seems to be broken
(Posted by cbk3982 3 years ago)
Will Crank, Will Not Go Forward Or Reverse
This was my dad's mower that sat for several years. The mower would not engage so we replaced the be...
This was my dad's mower that sat for several years. The mower would not engage so we replaced the be...
(Posted by PAULARVT 3 years ago)
Snow Throw Blades Not Engaging. Cable To Handle Loose.
Is there a way I can fix. Something must have come loose.
Is there a way I can fix. Something must have come loose.
(Posted by jimc6937 7 years ago)
I Have A 2000 Gth2654t Husqvarna Wont Back Up Or Go Forward I Checked Belts Fine
I Cant Even Get It To Shift In Nuetral The Pin U Pull Out To Push Mower Will Not Disingadge
I Cant Even Get It To Shift In Nuetral The Pin U Pull Out To Push Mower Will Not Disingadge
(Posted by agtg1966 10 years ago)