2004 Jeep Liberty Support Question
2004 Jeep Liberty Support Question
Find answers below for this question about 2004 Jeep Liberty.Need a 2004 Jeep Liberty manual? We have 1 online manual for this item!
Question posted by stroger on December 16th, 2013
How To Erase Garage Key Code In 2004 Jeep Liberty
The person who posted this question about this Jeep automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Manual Pages
Owner's Manual - Page 4
The two-wheel drive utility vehicle was designed for selecting a Jeep Liberty and welcome to our worldwide family. Always observe federal, state, provincial, and local laws wherever you are familiar with other severe conditions suited to become ...
Owner's Manual - Page 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A Word About Your Keys ...12 ▫ Ignition Key ...12 ▫ Key-In-Ignition Reminder ...14 Sentry Key Immobilizer System - If Equipped . .14 ▫ Important Note About Service ...15 ▫ Replacement Keys ...15 ▫ Customer Key Programming ...16 ▫ General Information ...16 Steering Wheel Lock - If Equipped ...17 ▫ To...
Owner's Manual - Page 12
... the bag, ask your new vehicle are enclosed in a plastic bag with the key code number on it. The key code can be obtained by the dealer from your vehicle invoice. Ignition Key Insert the key fully, then turn the switch to give you the number. The automatic transmission gear selector must be in the LOCK...
Owner's Manual - Page 13
... touch the parking brake, brake pedal, or the gear selector lever. Leaving children in a vehicle unattended is an invitation to LOCK and remove the key. Children should be injured. An unlocked vehicle is dangerous for a number of reasons. WARNING! THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
To remove the ...
Owner's Manual - Page 14
...turned on , this indicates that have an electronic chip (transponder) embedded into them. The Sentry Key Immobilizer System does not need to start and operate the vehicle for longer than 10 seconds) ...the ignition switch is turned on during normal vehicle operation (it is cut to remove the key. Operation of the system is automatic regardless of the vehicle by disabling the engine. During ...
Owner's Manual - Page 15
... (Transponder) fault unless the additional part is needed to any other transponder equipped components on your authorized dealer. This procedure
2 Once a Sentry Key has been programmed to a vehicle, it cannot be obtained from your customer invoice that have been programmed to start the vehicle.
Important Note About Service A ...
Owner's Manual - Page 16
... BEFORE STARTING YOUR VEHICLE
consists of programming a blank key to match the ignition switch lock cylinder key code. 2. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to a total of Industry Canada. Customer Key Programming You can program new keys to flash. The new Sentry Key has been programmed. Turn the ignition switch OFF and...
Owner's Manual - Page 17
...you turned the wheel to the right to engage the lock, you turn in either direction and the key is moved a half turn on the ignition after all the doors.
2 If you open any interference...THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
2. This lock prevents steering the vehicle without the ignition key. The lights also will remain on when you turned the wheel to the left to engage the...
Owner's Manual - Page 19
Therefore, make sure the keys are being displayed, the VF display will lock. Manual Door Locks Use the manual door lock plunger to only displaying the odometer/trip odometer mileage. ...
Owner's Manual - Page 20
..., lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. CAUTION!
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
•...
Owner's Manual - Page 21
... This will occur only once, will not reoccur until you press the door lock switch while the keys are in the ignition switch, and the driver's door is open, the doors will lock automatically ...If the plunger is down when the door is above 15 mph (24 km/h), 3. Therefore, make sure the keys are closed , the door will lock. and the accelerator pedal is on each front door panel. Press this switch...
Owner's Manual - Page 28
... door or the swing gate will set . In case one should go off in the future, you use the remote keyless entry transmitter or the key to deactivate it.
Owner's Manual - Page 29
REAR SWING GATE NOTE: The master key that is used to start the vehicle is armed (after 16 seconds), when you remain in the vehicle ...be locked but the Security Alarm will not arm. The door will arm unexpectedly. To unlock the rear swing gate, insert the key into the lock (if equipped) and turn counter clockwise. On vehicles equipped with power locks, the swing gate can create conditions ...
Owner's Manual - Page 32
...-up window.
NOTE: Close swing gate before flip-up window open can allow poisonous exhaust gases into your passengers could be injured by key, lock switch, or key fob). The window lock switch located next to the window switches allows you are located on rear wiper blade when closing swing gate, as...
Owner's Manual - Page 44
... belt. 2. The driver should also instruct all other occupants to turn off. 3. Turn the ignition key to the ACCESSORY/RUN position (engine does not need to be running), and wait for the Seat ...Belt Warning Light to buckle their seat belt. Turn the ignition key to the ON or START position. The Enhanced Warning System (BeltAlert) will be enabled or disabled...
Owner's Manual - Page 51
... into a size category based on sensor readings from within the seat cushion. If the occupant's weight is transferred to another object in a collision. If the key is first turned on.
feet on the AIRBAG warning light and PAD indicator light in the START or RUN positions. The ORC will turn off...
Owner's Manual - Page 57
... VEHICLE 57
Also, the fuel system will need it. Maintaining Your Airbag System
WARNING!
•
Modifications to any advanced airbag system service. turn the ignition key from the ON position to the LOCK position) after approximately 5 seconds in any way, take the vehicle to an authorized dealer for persons with disabilities...
Owner's Manual - Page 126
... device being programmed to programming HomeLink for the first time the factory test codes must be erased for security purposes. After approximately 20 seconds, the message CHANNELS CLEARED will appear...recommended that upon the sale of the vehicle, the programmed HomeLink buttons be erased. To erase HomeLink memory, press and hold the buttons for assistance, contact HomeLink at: www.homelink...
Owner's Manual - Page 128
...sequence a second time, and, depending on the brand of a rolling code equipped device (most commonly a garage door opener).
5. This can usually be equipped with steps five through seven below ...to complete the programming of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming...
Owner's Manual - Page 129
... of transmission - UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129
HomeLink should now activate your garage door opener's Owner's Manual for HomeLink to pick up the signal during the cycling... at www.homelink.com. Refer to clear (or erase ) the device's receiver memory. which may need to your rolling code equipped device. Gate Operator/Canadian Programming Canadian radio-frequency...
