Kenwood KDC-148 Support Question
Find answers below for this question about Kenwood KDC-148.Need a Kenwood KDC-148 manual? We have 2 online manuals for this item!
Question posted by Infamousregg on August 16th, 2013
Cd Function
just installed receiver, played cd once while it was skick inside cd drive. Managed to get cd out of unit, now it want take in cd's and it just spits it back out
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Kenwood KDC-148 Manual Pages
Instruction Manual - Page 1
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_1_72ae.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_1_72ae.png)
... the separation between the equipment and receiver. KDC-148 KDC-108 KDC-MP148CR
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D'EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this product so as to radio communications, if it is not installed and used in hazardous radiation exposure...
Instruction Manual - Page 2
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_2_38e5.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_2_38e5.png)
... to a disc
8
Selecting Repeat Play Selecting Random Play Selecting Scan Play Selecting a folder/track/file Direct Music Search using the remote
controller (RC-405)
Listening to the other external
components
9
Function settings
10
Troubleshooting
11
Installation/connection
12
Basic procedure Warning Caution Wiring connection Installing the unit
Specifications
15
WARNING Stop the car...
Instruction Manual - Page 3
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_3_d49d.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_3_d49d.png)
... play ...not expose the faceplate to use the remote controller for KDC-148/ KDC-MP148CR.
3 The faceplate is incorrectly replaced. Discs that ... software, and your disc recorder instruction manual.) 3-inch CD cannot be used batteries promptly.
Danger of explosion if ... much dust or the possibility of the unit and faceplate with your unit If this unit fails to operate properly, press the reset...
Instruction Manual - Page 5
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_5_83a3.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_5_83a3.png)
...tracks if pressed and held while in , "CALL" appears. AUD Enters [AUDIO CTRL] settings directly.
- Turns on . • If the source is...CD" is selectable only
when a disc is turned on . To continue listen to the previous level, press the button again. Enters [FUNCTION] settings.
Muting upon the reception of a disc.
- Selects the next/previous folder. (Pressing BAND on the main unit...
Instruction Manual - Page 6
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_6_0a98.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_6_0a98.png)
...FUNCTION]. 2 Turn the volume knob to select
[DEMO MODE], then press to enter. 3 Turn the volume knob to confirm. Clock minutes flashes on the display.
5 Turn the volume knob to adjust the hour, then press to finish the procedure. Press 4 / ¢ to move between audio file disc and music CD...15 seconds or if you turn on unless you reset the unit), the display shows:
[CANCEL DEMO] \ [PRESS] \...
Instruction Manual - Page 8
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_8_362d.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_8_362d.png)
... MP3/WMA : FILE SCAN, SCAN OFF
If scan play is selected, the unit resumes normal play of the music in the disc or the current folder. To return to make a selection. Selecting Scan Play Press number button 2 (SCAN) repeatedly to the root folder (or first track for audio CD), press BAND. "SEARCH" appears, then the current...
Instruction Manual - Page 9
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_9_702b.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_9_702b.png)
... : Selects track/file.
Although the audio files are complied with the standards listed above, the play maybe impossible depending on the external component and start playing. 3 Turn the volume knob to ...press or EXIT.
ENT
: Pauses/resumes playback.
About Audio file Playable Audio file: MP3 (.mp3), WMA (.wma) Playable disc media: CD-R/RW/ROM Playable disc file format: ISO 9660 Level ...
Instruction Manual - Page 10
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_10_79b1.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_10_79b1.png)
...Before making an MID LEVEL adjustment, select the source you want to adjust.)
TRE LEVEL BALANCE FADER
L15 - OFF:...Selects to confirm. Function settings
1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [AUDIO CTRL] or [SETTINGS...[AUDIO CTRL] : While listening to [ON].
[SETTINGS]
Item
Selectable setting (Preset: *)
AUX NAME AUX*/ DVD/ PORTABLE/ GAME/ VIDEO/ ...
Instruction Manual - Page 11
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_11_f1e6.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_11_f1e6.png)
... "PROTECT" does not disappear, consult your nearest service center. The CD player is not correct.
Elapsed playing time is not operating properly.
Insert a playable disc into the loading slot.
The unit is generated. Noise is playing an unsupported audio file.
This unit can be sure the terminals of
album name). If the condition did not improve...
Instruction Manual - Page 12
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_12_38fb.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_12_38fb.png)
...
(KDC-148/ KDC-MP148CR only 1) E Wiring harness 1) F Removal tool 2) G Flat head screw (for Nissan cars 4) H Round head screw (for Toyota cars).... (×4)
Basic procedure
1 Remove the key from the ignition switch, then disconnect the · terminal of the car battery.
2 Make proper input and output wire connections. \ "Wiring connection" (page 13)
3 Install the unit to...
Instruction Manual - Page 15
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_15_8f15.png)
![](/manualimages/6/i/kenwood-kdc148-instruction-manual-e984354_15_8f15.png)
... Frequency range: For KDC-148/ KDC-108: 200 kHz space: 87.9 MHz - 107.9 MHz For KDC-MP148CR: 50 kHz ...CD): 2 000 mV/10 kΩ Preout impedance: ≤ 600 Ω
Auxiliary input section Frequency response (±3 dB): 20 Hz - 20 kHz Input maximum voltage: 1 200 mV Input impedance: 10 kΩ
General Operating voltage (11 V - 16 V allowable): 14.4 V Maximum current consumption: 10 A Installation...
User Manual - Page 1
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_1_f332.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_1_f332.png)
...installation and operation procedures will help you obtain the best performance from your Kenwood dealer for
Windows Media'"
Take the time to the model and serial numbers whenever you call upon your new CO-receiver. For your records
Record the serial number, found on the back of the unit...~!'
KENWOOD
KDC-148 KDC-108 KDC-MP148CR
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE ...
User Manual - Page 2
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_2_6a97.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_2_6a97.png)
... mode Adjusting the clock Initial settings before operating the unit. Driving with your model and in an online manual on the laser lens. Important to the other external
components
9
Function settings
10
Troubleshooting
11
Installation/connection
12
Basic procedure Warning Caution Wiring connection Installing the unit
Specifications
15
WARNING Stop the car before operations...
User Manual - Page 5
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_5_a13d.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_5_a13d.png)
...disc is ready, playback also starts. Enters [FUNCTION] settings.
*AM-/ #FM+
• ... (page 6) if pressed and
held while in , "CALL" appears. • The audio system pauses. • To continue listen to the auxiliary input jack.
+
1+llI/~...loaded. Selects the available sources (TUNER, CD, AUX, STANDBY), if the
SRC
power is turned on the main unit will also exit from setting mode. •...
User Manual - Page 6
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_6_2cc8.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_6_2cc8.png)
.../ ~ to move between audio file disc and music CD. ; 2: Forces to confirm.
OFF: Disables"AUX" in source selection. Setting the demonstration mode
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume ... below for optimum performance.
6 Clock hour flashes on the rear ofthe unit (through an external amplifier). KEY BEEP ON*/ OFF: Activates/deactivates the keypress tone. Turn...
User Manual - Page 8
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_8_9dff.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_8_9dff.png)
... number button 2 (SCAN) repeatedly to resume/pause playback (if necessary).
If "SCAN OFF" is selected, the unit resumes normal play is available.
8
to make a selection. Audio CD : DISC RANDOM, RANDOM OFF MP3IWMA: FOLD (folder) RANDOM,
ALL RANDOM, RANDOM OFF • Press and hold ~. • < or > on the power. 2 Insert a disc into the ...
User Manual - Page 9
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_9_6d54.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_9_6d54.png)
...... ENT ~..
: Pauses/resumes playback.
About Audio file • Playable Audio file: MP3 (.mp3), WMA (.wma) • Playable disc media: CD-R/RW/ROM • Playable disc file format:... Direct Music Search Mode. Although the audio files are complied with the standards listed above, the play maybe impossible depending on the external component and start playing. 3 Turn the volume knob to ...
User Manual - Page 10
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_10_4ba3.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_10_4ba3.png)
...when you change the
source. (Before making an MID LEVEl adjustment, select the source you want to the subwoofer. ; 85Hz/120HZI 160HZ: Frequencies
higher than [THROUGH] is selected for ...to any source except in each source. FADER
R15 -
Function settings
1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter. 3 Turn...
User Manual - Page 12
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_12_aac2.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_12_aac2.png)
...; Be sure to ground this unit to your vehicle. Use only the screws provided.
• Install this work if you connect the ignition wire to a power source with the ignition key. Installation/connection
Part list:
® Faceplate
(xl)
® Escutcheon
(xl)
© Mounting sleeve
(xl)
@ Casing for faceplate
(KDC-148/ KDC-MP148CR only)
(xl)
® Wiring...
User Manual - Page 15
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_15_cef1.png)
![](/manualimages/q/m/kenwood-kdc148-user-manual-474674e_15_cef1.png)
...KDC-l481 KDC-108: 200 kHz space: 87.9 MHz For KDC... 12 Audio
Layer-3 WMA decode: Compliant with Windows
Media Audio
Audio sedion...CD): 2 000 mV/10 kO
Preout impedance: s 600 0
Auxiliary input sedion
Frequency response (±3 dB): 20 Hz - 20 kHz Input maximum voltage: 1 200 mV Input impedance: 10 kO
General
Operating voltage (11 V-16 Vallowable): 14.4 V Maximum current consumption: 10 A Installation...
Similar Questions
Kenwood Kdc 148 Stuck In Demo Mode Cd Wont Eject
(Posted by kchristi1921 11 years ago)
How Do I Turn On The Kenwood Kdc-148 Cd Player?
(Posted by Anonymous-80410 11 years ago)