Lexmark E450DN Support Question
Lexmark E450DN Support Question
Find answers below for this question about Lexmark E450DN - E 450dn B/W Laser Printer.Need a Lexmark E450DN manual? We have 5 online manuals for this item!
Question posted by fili1fo on August 26th, 2014
How To Reset Lexmark E450dn Printer
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Lexmark E450DN Manual Pages
User's Guide - Page 25
...you loaded, and then press . 6 Press until it becomes empty, and then the printer automatically feeds print media from the Lexmark Web site.
If you load the same size print media in order to link the ...for trays when you load the same size and type of the available printer settings you can also use the Lexmark custom printer drivers supplied with the same size and type of the trays. To...
User's Guide - Page 65
... you harm.
Electronic emission notices
Federal Communications Commission (FCC) compliance information statement
The Lexmark E450dn, Machine Type 4512-630, has been tested and found to this device may cause... residential area is not responsible for use a properly shielded and grounded cable such as Lexmark part number 1021294 for USB attach or 1021231 for a Class B digital device, pursuant...
User's Guide - Page 67
...terms of original purchase. If you may be required to that user for Lexmark E450dn
Lexmark International, Inc. To obtain warranty service you transfer this product to present ... produced by a Lexmark warranty, technical support may be available for repair or replacement (at http://support.lexmark.com. Laser notice
The printer is certified as a Class I laser product conforming to that...
Menus and Messages - Page 16
... the size and number of the paper
16 PCL emulation-Uses a PCL interpreter for incoming host communications. Printer retains all downloaded resources for all printer languages during language changes and printer resets.
The resources remain in printer memory (RAM). Menu selection Duplex
Purpose
Values
Sets duplexing as fonts
and macros stored in the non-printable...
Service Manual - Page 1
Edition: July 2, 2008
Lexmark™ E450dn
4512-630
• Table of contents • Start diagnostics • Safety and notices • Trademarks • Index
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Service Manual - Page 17
... correct field replaceable unit (FRU) or part.
Use the error code charts, symptom index, and service checks to help identify parts. General information
The Lexmark™ E450dn is a monochrome laser printer designed for more information on page 2-1 for single users or small workgroups. This book contains information on legal). See "Diagnostics information" on E250d...
Service Manual - Page 19
... Optional SDRAM 256MB Maximum DRAM Optional flash memory 32MB Optional font cards (DBCS)
Print quality
4512-630 Lexmark E450dn
64MB
320MB 1 1
Resolution
4512-630 Lexmark E450dn
1200 Image quality ¹
✔
2400 Image quality ²
✔
1200 x 1200 dpi... 1200 dpi at ½ rated speed. 4 Although the printer supports the 300 dpi resolution, it doesn't support a 300 dpi driver.
Service Manual - Page 20
actual yield may vary
4512-630 Lexmark E450dn
✔ ✔ optional optional
3,000 standard pages ¹ n/a
Up to 30,000 ²
1-4 Service Manual 4512-630
Media trays and supply capacity
Item
Available input ...
Service Manual - Page 21
4512-630
Connectivity and compatibility
Item
4512-630 Lexmark E450dn
Data stream emulations
PCL 6
✔
PostScript Level III
✔
Host Based Printing (HBP)/... 2.0 certified device supporting high-speed (480MB/sec.) data transfer.
¹ Linux support for E450dn model is utilizing the PCL data stream. ² Only one slot active for flash memory or font card
General information 1-5
Service Manual - Page 90
Open the front access cover. 3. In the same manner, move the left hinge from its pivot point.
4-2 Lexmark™ E450dn Extract the cable, and unhook the access cover by pressing the right hinge to the right until it can be lifted
up and away from ...
Service Manual - Page 92
Open the front access cover. 3. Unlatch the cover from the printer.
4-4 Lexmark™ E450dn Open the rear door. 4. Lift the top rear of the cover over the edge of the table. 7. Position the printer with the left rear corner hanging over the pivot point, and drop the cover away from the latches (B).
6. Swing the cover...
Service Manual - Page 94
.... 5. Note: In re-installation, check to make sure that the fuser ground cable is routed out of the way and is not pinched or damaged.
4-6 Lexmark™ E450dn Lift the rear cover, unhooking it from the frame at the bottom, and remove. 4512-630
Rear cover removal 1.
Service Manual - Page 96
... location of
the exit tray.
• Verify that the rollers in the top cover contact the exit guide rollers at the rear of the rollers.
4-8 Lexmark™ E450dn
Service Manual - Page 98
... a finger or small screwdriver against the coupler behind the clutch.
Remove the left side cover. Remove the screws (A). A 4. Remove the auto comp clutch.
4-10 Lexmark™ E450dn Note: Resistance to loosening the screw may have to be applied to remove the auto comp.
4512-630
6. See "Left side cover removal" on page...
Service Manual - Page 106
... (B) on page 3-26. 6. Remove the right side cover. See "LVPS/HVPS card assembly removal" on the other side of the printer. See "Right side cover removal" on page 3-33.
4-18 Lexmark™ E450dn Remove the top LVPS/HVPS shield: a. Remove the screw (A) and the screw (B) at the controller shield.
See "Media level indicator...
Service Manual - Page 112
... frame. 4.
Note: The connector latch (D) is toward the side frame as shown.
4-24 Lexmark™ E450dn Disconnect the power cable from the LVPS/HVPS side. Use the hook end of a spring hook to mar the finish of the printer.
5. Remove the paper exit guide assembly. 4512-630
Fuser power cable removal 1. See "Paper...
Service Manual - Page 114
See "Rear cover removal" on the side shown.
4-26 Lexmark™ E450dn Remove the four screws (A), the machine screw (B) and the machine screw (C). 4. Note: Be careful not to mar the finish of the printer.
3. Place the printer onto its top with the back and bottom in the left side frame.
5. Lift the metal cover so...
Service Manual - Page 116
... remove the developer drive spring (E).
4-28 Lexmark™ E450dn Be sure to remove this strap, and install it in the main motor drive FRU. Lift the motor end, and disconnect the main motor cable (D). See "Left side cover removal" on page 4-4 for more information. 2. Tilt the printer onto its right side, and remove...
Service Manual - Page 118
...the cable from the screws. 3. Re-installation note:
• Insert the hook end of the spring hook through the opening of the printer.
5. Place the machine on the duplex and auto comp. 6. Extend the
hook until the sensor connector can be hooked.
• Hook... not to the connector, and pull it through the three retainers between the sensor and
side frame.
4-30 Lexmark™ E450dn
Service Manual - Page 124
...the same time. Unlatch the four latches on the panel cover. 8.
Each card contains the printer settings. Remove the bezel. Open the front cover. 2. Close the front cover. 6. Remove...: Do not replace the operator panel and the controller card at the same time.
4-36 Lexmark™ E450dn 4512-630
Operator panel removal 1. Pull the bottom edge out until it obtains its retainers. ...
Similar Questions
How To Reset Lexmark Printer T654dn After Maintance Kit Is Installed
(Posted by zoeygroove 9 years ago)
How Do I Change The Gateway To An E450dn Printer?
step by step detail
step by step detail
(Posted by pfcballard0303 11 years ago)
How Do We Program The Printer To The Computer When We Lost The Cd To Program It?
Steps To Ho W To Program The Printer When We Dont Have The Cd
Steps To Ho W To Program The Printer When We Dont Have The Cd
(Posted by andreazuniga30 11 years ago)
My Printer Suddenly Wont Prink In Black
I chose the option to print in black ink only and now it prints blank paper...i cant figure out how ...
I chose the option to print in black ink only and now it prints blank paper...i cant figure out how ...
(Posted by mlainson 11 years ago)
How Do I Reset The Printer Once I Have Replaced The Photoconductors?
Lexmark 734dn color printer
Lexmark 734dn color printer
(Posted by msoulliard 11 years ago)