Metabo DSD 250 Support Question
Metabo DSD 250 Support Question
Find answers below for this question about Metabo DSD 250.Need a Metabo DSD 250 manual? We have 1 online manual for this item!
Question posted by denisstanic on September 18th, 2014
Low Rpm On Metabo Dsd 250
We have 3 phase 400Volts without neutral line on board. I install brand new DSD 250 and have not enough RPMs and power on it ( I can see 5 core cable, means, using 230 Volts for control drive or ??? ). Thanks, rgds Denis
Current Answers
Related Metabo DSD 250 Manual Pages
Operating Instructions - Page 2
n0
min-1
(rpm)
2980
2980
2980 2980 2980 2980
1490
2980
P1
W
500
200
.../ 3
88 / 3 83 / 3 87 / 3 87 / 3 87,5 / 3 81 / 3
LpAI/KpAI dB(A)
-
-
-
-
-
-
74 / 3
-
BS 175 DS 125 DS 150 DS 175 DS 200 DSD 200 DSD 250 TNS 175
13
Dmax x B
mm
(in)
175x25
(6 7/8 x 1)
125x20 150x20 175x25 200x25 200x25 250x40 175x25
(4 15/16 x 25/32) (5 29/32x 25/32) (6 7/8 x 1) (7 7/8 x 1) (7 7/8 x...
Operating Instructions - Page 11
...suitable for any damage caused by buying a new Metabo power tool. The grinding wheel must be made of elastic materials, e.g. Do not use . soft cardboard etc.
Keep all safety ...Each Metabo power tool is guided by Metabo's quality assurance. Failure to strict quality controls by hand. The grinders are not suitable for grinding aluminium, magnesium or other cutting tools, in...
Operating Instructions - Page 12
...ignite inflammable substances. Clean, check and perform maintenance work place must be used. - Regularly check the power cable on the sides. Swivel the eye preservers (9) downwards before making any... small enough, to be correctly installed and fulfil all conditions necessary to health (e.g. Follow national requirements for possible damage: Before using the grinder, protective devices or ...
Operating Instructions - Page 13
...Installing workpiece support
Install workpiece support (8) as shown in the wrong direction: Unplug the grinder. All persons must be bolted down the machine.
7.5 Dust extraction connection (depending on equipment)
If your power... C, page 3).
13 DSD 200, DSD 250 (three-phase version): Ensure that the maximum distance of extraction connection piece: 35 mm. Use a Phillips screwdriver to ...
Operating Instructions - Page 14
...power is restored after the grinding wheel has been changed. Roughly 1/3 of the wet grinding wheel should be able to or greater than the maximum idling speed specified on the identification plate of the danger zone when this is either too low..., check and perform maintenance work .
9.1 Grinding wheel change
Use only original Metabo grinding wheels. Switch machine on and off when the plug ...
Operating Instructions - Page 15
...- Fill the water container with your power tool. a
10 Accessories
Use only genuine Metabo accessories.
Remove clamping flange (3) and grinding... 6.30657 60 N 6.30656 D= 200 mm: 36 P 6.30784 60 N 6.30785 D= 250 mm: 36 P 6.30636 60 N 6.30637 Wet grinding wheel D= 200 mm 0900025653
B Stand...and lower the water container. - Place the new sanding belt on the rollers so that its direction...
Operating Instructions - Page 16
... EN 61029.
Only for environmentally compatible recycling.
13 Technical Specifications
Explanatory notes on the specifications on page 2. For addresses see www.metabo.com. The technical specifications quoted are printed on used power tools must be carried out by qualified electricians ONLY! Changes due to tolerances (in conformity with the relevant valid standards).
12 Environmental...
Operating Instructions - Page 84
Dmax =
D N,max =
d
=
dN =
B
=
A
=
n0
=
P1
=
P2
=
84
x
www.metabo.com.
12
Metabo είναι 100
2002/96
MK
m
= Βάρ ς
LpA L WA LpAI K...
80 dB(A). EL
11
Metabo Metabo www.metabo.com. EN 61029.
13
2.
Similar Questions
How To Remove The Flange Nut From The Metabo Dad 250 Bench Grinder
(Posted by Chazsmith 2 years ago)
This Grinder Drops' Rpm By Itself After Startup.
I have replaced the speed reducer unit with a new one, but it stills' drops' rpm after 20 seconds' o...
I have replaced the speed reducer unit with a new one, but it stills' drops' rpm after 20 seconds' o...
(Posted by paulhanson22 8 years ago)
How Do I Determine If My Metabo Power Tools Is Under Warranty?
My Metabo power tools stopped working within a few days of purchase. Is it under warranty, and do I ...
My Metabo power tools stopped working within a few days of purchase. Is it under warranty, and do I ...
(Posted by Anonymous-138112 14 years ago)