NaceCare TTB1620T Support Question
NaceCare TTB1620T Support Question
Find answers below for this question about NaceCare TTB1620T.Need a NaceCare TTB1620T manual? We have 1 online manual for this item!
Question posted by dwbelding on November 17th, 2016
Machine Quits Alot
My TTB 1620 machine will constantly quits while it is being used. I turn the machine off and back on and it works again for a time. The display says lo-flo. I'm using the correct pad for the floor type. Its being charged properly. I've checked to make sure there is not to much load on the pad. Please help.
Current Answers
Answer #1: Posted by BusterDoogen on November 17th, 2016 9:57 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,447
Member since:
October 30th, 2011 Points: 28,565,447
Machine just 'stops' while operating: To much load on the brush system Reset the machine using the key and decrease the brush load to best suit the floor type.
Failure to rectify the problem or in the event of a breakdown contact your Nacecare dealer or the Nacecare Technical helpline +44 (0) 900 1 905 785 0038.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related NaceCare TTB1620T Manual Pages
TTB1620T Owners Manual - Page 1
Read instructions before using the machine. Attention Lisez la notice avant d'utiliser la machine. Owner Instructions Mode d'emploi
TTB - 1620 / 100T
(TTB 6055T)
www.numatic.com
Original Instructions Warning!
TTB1620T Owners Manual - Page 5
... Description 3 Voltage Frequency 4 Power rating 5 Max Gradient 6 Weight (ready to use) 7 Splash Proof Rating 8 Machine yr/wk Serial number
9 1
10 2
3 11
4
7
5
6
8
About the Machine
9 Machine Description 10 Noise Rating 11 Hand Arm Vibration
PPE
(Personal protective equipment) that may be worn.
Safety Critical Component
Charging Lead:18 AWG x 3 core SJTW Cable Battery Charger: 120 Volt...
TTB1620T Owners Manual - Page 6
... with all electrical equipment care and attention must be exercised at all times during its safe operation.
This machine is well illuminated.
• Pre-sweep the area to be cleaned.
• Use steam cleaners or pressure washers to the correct standard could render this equipment unsafe and the manufacturer can accept no responsibility or liability...
TTB1620T Owners Manual - Page 7
... recharge them. Only use brushes or pads which are Valve Regulated Lead Acid (VRLA) gel electrolyte type. It is essential that marked on the machine.
Do not smoke or bring naked flames into the charging area. 3. Rings, chains etc. The batteries must be possible to the correct use of the machine for the correct operation of the machine. The batteries...
TTB1620T Owners Manual - Page 8
... individually to operate machine working
Traction drive disabled. Contact Service Agent
Check connections on Product
Operating time severely reduced or machine will not operate Check...Batteries not been charged
Possible bad connection between the motor and controller
Machine functions not Check battery voltage and charge current
Charge batteries immediately
working
ensure voltage <...
TTB1620T Owners Manual - Page 9
... great. * Brush current exceeds 32A * Wrong type of brush. * Restart machine.
* Brush LED's all flash in unision until the trigger is being used, including the off aisle mode selected. * Faulty Float switch.
* Vac. T = Total time.
Contact Service Agent.
9
LCD Display Blank 'OVER CURRENT'
'UNDER VOLTS' ' TANK FULL' 'CHARGING'
LCD Display' and fault codes
Fault
Possible Cause
Effect...
TTB1620T Owners Manual - Page 10
... on the brush system
SOLUTION
Fit or replace fuse (page 30) Turn key to 'ON' position (page 22) Charge batteries (page 29) Take off charge (page 29)
Empty waste water tank (page 23)
Empty waste-water... as desired (Page 22) Lower brush deck (page 22)
Reset the machine using the key and decrease the brush load to best suit the floor type (page 23)
Failure to rectify the problem or in the event of ...
TTB1620T Owners Manual - Page 18
... button is released (Fig 3). Fig 5
When the machine is set to the 'ON' position. Fig 6
18 Fig 4
Depress control handle with a built in a safe position, turn clockwise to forward position (Fig 4).
Select the slow speed... Ensure that no metal objects come into master control on/off and turn quarter-turn key back to the off of the pallet (Fig 5), this control panel has been designed...
TTB1620T Owners Manual - Page 19
... brush
Fig.11
Fig 10
Use either a 20" Brush or a 20" Pad
Fig.12
Featuring the new OBS (Octagonal Brush System); Slide the brush under the brush deck (fig 11). ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS
! Fitting the floor-tool
Fig 9
! Note: Raise floor-tool again before driving to...
TTB1620T Owners Manual - Page 20
... the rear of the machine in a single fill.
The clean water bottom tank holds 16 US Gall
Fig 18
20 Machine Set Up
Filling the clean water tank
The TTB 1620 T is always clean and free from debris.
Open the stopper (Fig 15) and place hose under water tap, or use a hose to commence filling...
TTB1620T Owners Manual - Page 21
... (waste) tank is fitted with the Floor tool in auto scrubber-driers.
!
Move the Floor tool lever, to suit the cleaning conditions.
Important
Do not operate machine unless the Operator Manual has been read and fully understood.
!
When handling and mixing chemicals. Only use chemicals recommended for use in the lowered position, this could possibly...
TTB1620T Owners Manual - Page 22
...floor type and level of soiling
0.13 gpm 0.26 gpm 0.52 gpm 0.79 gpm
Set desired traction Speed as required, depending on /off and quarter-turn it clockwise to the 'ON' position. The TTB 1620T has been fitted with a Hi -
With the machine running normally the Hi -
Lo...seconds.
Lo mode start the machine in the normal way. The battery charge-level indicator will NOT be made using the ...
TTB1620T Owners Manual - Page 23
...
To reset, turn the master control on the control display shows the pressure applied, when the machine is being operated.
(A) Standard Duty 34.5 lbs Pressure
(Fig 23)
B
Fig 23
A
(B) Heavy Duty 66 lbs Pressure
(Fig 24)
Fig 24
NOTE: It is recommended the heavy duty option is NOT used all the time and is for...
TTB1620T Owners Manual - Page 24
FEED' scrubbing brushes.
On heavily soiled floors use
To operate, turn on automatically and the machine will move forward. Allowing it become caught on /off key to work then scrub the area a second time with the floor-tool in use a 'double scrub' technique.
24
Adjust the speed to safely disengage from its holder. Fig 28
The waste water is...
TTB1620T Owners Manual - Page 25
...Press the off aisle button on the control panel (see Fig 30) to the floor tool once finished using the off aisle facility.
Off-Aisle Cleaning Kit (Optional Extra Accessory)606182
Fig 30...the off aisle light will disable all the machine functions accept for the vacuum allowing for normal use of the off aisle function. Return the hose to turn on the control panel. Off-Aisle Accessory ...
TTB1620T Owners Manual - Page 26
... when working in the top tank hood toggles, remove the hood (Fig 32) The hood also has a sealing-rubber which should be examined at regular intervals.
After use the machine without the... recommended filter as it may cause damage to the rear of batteries. Unscrew the cap check the filter condition (Fig 34), rinse and refit. A
Next remove floor-tool...
TTB1620T Owners Manual - Page 27
... main body
1
2. Rear blade
3. ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF PRIOR TO ANY MAINTENANCE USING THE MASTER CONTROL ON/OFF KEY.
Floor-tool overview
1. Front blade (slotted)
2
5.
The blade removal is a reversal of the removal process. Changing the Floor Tool Blades
! Rinse the floor-tool assembly with clean water and refit. Simply start...
TTB1620T Owners Manual - Page 28
... 41). The motor brake is equipped with a free-wheel function that will now be fully disengaged. The motor brake will work whilst in full free-wheel mode.
NEVER DISENGAGE THE BRAKE WHEN THE MACHINE
IS ON A SLOPE / GRADIENT
! The TTB 1620 / 100T is located on the right side of the other functions on the...
TTB1620T Owners Manual - Page 30
... sequence (Fig 48). Batteries should be fully charged and battery fuses removed using the machine again.
30 Yellow:- Charging Stopped Automatically, 27 hours MAX Remove Mains Supply Recharge the machine fully after each use ;
leaving the machine without charging for a period of Viewing panel for a period of machine operation time.
Fully Charged
Red:- we advise that you start...
TTB1620T Owners Manual - Page 48
This machine has been packed with the following. Charging Lead Brush Floor Tool Fuses Hose Hook
38 / 32mm Adaptor
Signed
Serial Number
TTB 6055/100T
Distributed by
244125 / 02/13 (A02)
Similar Questions
Wont Spray
i cannot get spray to come out of machine. I have cleaned the spray tip.
i cannot get spray to come out of machine. I have cleaned the spray tip.
(Posted by vzopfsummit 2 years ago)
The Clock On The Phone Did't Change When Time Changed Help
(Posted by Anonymous-157960 8 years ago)
Pressure Issue With Rm1800h
The hose attachment for my RM1800H doesn't generate a lot of pressure when I use it, and the stream ...
The hose attachment for my RM1800H doesn't generate a lot of pressure when I use it, and the stream ...
(Posted by williamhodge 8 years ago)
Are There After Market Warranties Available For My Nacecare Pressure Washer?
I lost the original warranty registration card for my NaceCare pressure washer. How do I find out if...
I lost the original warranty registration card for my NaceCare pressure washer. How do I find out if...
(Posted by Anonymous-152116 13 years ago)