Pioneer PRO-1540HD Support Question
Pioneer PRO-1540HD Support Question
Find answers below for this question about Pioneer PRO-1540HD.Need a Pioneer PRO-1540HD manual? We have 1 online manual for this item!
Question posted by lbgart on May 29th, 2011
Will Not Turn On
I have no red or green light on my Pioneer 1540 & it will not turn on
Current Answers
Answer #1: Posted by jdvillanueva on May 31st, 2011 5:12 AM
jdvillanueva
Member since:
May 9th, 2011 Points: 33,360
Member since:
May 9th, 2011 Points: 33,360
Hi,
Here are some basic steps that will help you fixing the problem.
I'm assuming that your unit is dead set without an standby LED light and your outlet is live.1.Power cord - check the cord it might be opened (no continuity).This is due to frequent bending,pulling. 2. Power switch - check for dry joints, open contact. 3.Check the internal fuse- sometimes the fuse fail because of the power surge, replacing with new one will cure the problem, If this is the case I would advice you to use surge protector/AVR (Automatic Voltage Regulator). However if the fuse blew again this is an indication that you have a shorted parts in the power supply. If no reaction and still the unit didn't power up then you have an open parts on the power supply.
4.If you see that the fuse is intact , don't attempt to touch anything because there some fatalcomponents stored electricity enough to hurt you with a simple mistake only. I would advice you to look for a professional to troubleshoot the power supply. If you want to repair it yourself make sure that you have necessary tools and test instrument. First check bad solder joints(re-solder all cold solder), leaky electrolytic capacitor(sometimes it has bulged at the top but not all, you better have a capacitor checker), open/shorted regulator transistor/IC(mounted in heat sink), open fusible resistor (caused by shorted regulator Transistor/IC), shorted zener diode.
You may also replace the entire power supply board.
Also check if your unit is under warranty before opening the back panel, it will void the warranty. Avail it because the manufacturer of your unit will fix it for free.
Best Regards,
JDV
Related Pioneer PRO-1540HD Manual Pages
Owner's Manual - Page 3
...Plasma Display System
Model Number: PRO-1540HD/PRO-1140HD/PRO-940HD
Product Category: Class B Personal Computers & Peripherals
Responsible Party Name: PIONEER...is lit red when the...or strong artificial light) Operation is ...televisions, use shielded cables and connectors for help.
However, there is no longer fully operational.
However, the
Plasma...can be determined by turning the equipment off ...
Owner's Manual - Page 4
...Plasma Display 20 Preventing the Plasma Display from that shown in the explanatory drawings. However the method of the power plug and power outlet may sometimes differ from Falling Over 21 Attaching/detaching the PIONEER stand (for PRO... (MPAA 39 Setting the TV ratings 39
06 Basic Operations
Turning on the power 26 Turning off the power 26 Watching TV channels 27
Selecting the antenna...
Owner's Manual - Page 7
...Filter. It also eliminates the need for example, a traditional tube-type television).
PIONEER is strongly recommended. Important User Guidance Information
01
Important User Guidance Information
English
In order to obtain maximum enjoyment from this Pioneer PureVision PRO-1540HD/PRO-1140HD/PRO-940HD Plasma Display Panel, please first read and follow the usage guidelines below...
Owner's Manual - Page 10
...product, please read the following instructions when installing, operating and cleaning the product. PRO-1540HD - 51.5 kg (113.6 lbs.)
- PRO-940HD - 31.7 kg (69.9 lbs.) (with stand)
Unpacking, carrying, and... of the panel. Overloading can cause overheating and/or shorten the life of each Plasma Display Panel is not designed for future reference.
• Observe all operating instructions....
Owner's Manual - Page 11
... their use. Holes other than the
optional PIONEER products.
11
En
When using other than those shown above show the location of the Plasma Display. See the side view above. ... and should not be liable for the installation:
Rear view (PRO-1540HD)
Side view Mounting surface
Mounting hole
Mounting
hole Median line
Plasma Display
Mounting bracket (or equivalent item)
M8 screw
12 mm ...
Owner's Manual - Page 12
...; 3
Warranty card
G-LINK cable (3 m/9.8 feet)
Ferrite core
Remote control unit
AA size battery x 2 (Alkaline battery for remote control unit)
Hexagonal wrench x 1 (Diagonal size: 6 mm) (for PRO-940HD only)
Terminal position sheet (for use when mounting the Plasma Display on the wall) (for PRO-1540HD only)
12
En
Owner's Manual - Page 13
Part Names Part Names
Plasma Display
Front/side view (PRO-1540HD)
11
12
13 14
1
1 a POWER button (See page 26)
2 POWER ON indicator (See page 26)
3 STANDBY indicator (See page 26)
4 REC TIMER indicator 5 Remote control ...
Owner's Manual - Page 16
04 Part Names
Rear view (PRO-1540HD)
17 18 21 22 23
12
3
45
11 12 13 14 15 16
19 20 24
25 6 7 26
27 28
8 9 10
(Terminals located on the ...
Owner's Manual - Page 20
... ensure proper ventilation. Therefore, at all times.
20
En
Using the optional PIONEER speakers (for PRO-1540HD and PRO-1140HD) • For details on a rack, etc., someone help
you when moving or installing the panel.
Moving the Plasma Display
(PRO-1540HD)
CAUTION
• These Plasma Display Panels are thin and can be unstable when held upright.
NOTE •...
Owner's Manual - Page 22
...Slowly ease the panel down on the supports. • Be extremely careful not to the Plasma Display at the points
indicated by detaching the stand.
En If the panel is mounted improperly...22
• Do not tighten them with the PIONEER table top stand attached. 05 Preparation
Attaching/detaching the PIONEER stand (for PRO-940HD only)
The PRO-940HD comes with more people are required to ...
Owner's Manual - Page 25
... [1] into an appropriate hole on the rear of the Plasma Display then snap [2] into the back of [1] to lock the clamp. for PRO-1540HD
for PRO-1140HD
for a long period of the compartment. Use pliers... view
NOTE
• Always turn the panel's power OFF when connecting or disconnecting power cords.
• Disconnect the power cord from the wall outlet when the Plasma Display Panel is not going ...
Owner's Manual - Page 26
... the current status of the display (left).
Press POWER then wait for a long period of the Plasma Display Panel. Plasma Display (PRO-1540HD)
POWER button POWER ON indicator STANDBY indicator
(PRO-1140HD) POWER button
Turning off . • The STANDBY indicator on the Plasma Display lights up
red.
2 Press TV a on the remote control unit or STANDBY/ON
on the...
Owner's Manual - Page 36
... Configuration
AV mode menus
Home Menu Picture
Item AV Selection Contrast Brightness Color Tint Sharpness Pro Adjust Reset
Sound
Treble Bass Balance Reset FOCUS Front Surround
Power Control
Energy Save No Signal... - 44 44
75 - 91
PC mode menus
Home Menu Picture
Item AV Selection Contrast Brightness Red Green Blue Reset
Page 57 58 58 58 58 58 58
Sound
Treble
62
Bass
62
Balance
62
...
Owner's Manual - Page 39
...the setting is switched. • A lock icon appears beside the blocked rating. • The Plasma Display ships with all ratings unblocked.
7 Press HOME MENU to exit the menu. NOTE
•...8226; A confirmation screen appears.
7 Press A. 8 Press HOME MENU to exit the menu.
PRO-1540HD/PRO-1140HD/PRO-940HD Your password No.:
If you write down for 3 seconds or longer. The password reverts to...
Owner's Manual - Page 44
... Opacity
Selection Auto/ Large/ Standard/ Small
Auto/ Font 1/ Font 2/ Font 3/ Font 4/ Font 5/ Font 6/ Font 7
Auto/ Black/ White/ Red/ Green/ Blue/ Yellow/ Magenta/ Cyan
Auto/ Solid/ Transparent/ Translucent/Flashing
Auto/ Black/ White/ Red/ Green/ Blue/ Yellow/ Magenta/ Cyan
Auto/ Solid/ Transparent/ Translucent
1 Font 1 (monospaced with serifs)/ Font 2 (proportionally spaced with serifs)/ Font...
Owner's Manual - Page 58
... 40 0 0 0 0
4 Select the desired level. ( / )
Contrast
40
For PC source, the following screen appears:
Picture AV Selection Contrast Brightness Red Green Blue Reset
STANDARD 40 0 0 0 0
NOTE
• To perform advanced picture adjustments, select "Pro Adjust" in step 3 then press ENTER. Press / to select "Yes" then press ENTER.
• When an adjustment screen is...
Owner's Manual - Page 59
...red For weaker green For weaker blue
For stronger red For stronger green For stronger blue
R Low G Low B Low
Fine adjustment for dark portions
For weaker red For weaker green For weaker blue
For stronger red For stronger green... MENU.
2 Select "Picture". ( / then ENTER)
3 Select "Pro Adjust". ( / then ENTER)
4 Select "Color Detail". ( /... picture adjustments
The Plasma Display System provides ...
Owner's Manual - Page 105
...profile. If one of the Plasma Display is high. SD05
(PRO-1540HD/PRO-1140HD) Internal protection circuit turns power off . Check the speaker cable connections between the Plasma Display and the speakers. It... that comply with the supported format may not be performed. • See the Pioneer website (www.pioneerelectronics.com) for details. When using a digital camera that is not...
Owner's Manual - Page 109
... software patents. These restrictions translate to make sure that you can apply it in the OpenSSL Toolkit. (http://www.openssl.org/)"
Linux Source Notice The Pioneer Plasma Television is powered by others will individually obtain patent licenses, in the term "modification".) Each licensee is modified by someone else and passed on the original...
Owner's Manual - Page 117
...
8 Ω to 16 Ω
8 Ω to 16 Ω
SUB WOOFER OUTPUT Variable
CableCARD
Point of pixels Audio Amplifier Speakers
Surround System Power Requirement
Weight
60" Plasma Display Model: PRO-1540HD 1365 × 768 pixels 13 W + 13 W (1 kHz, 10 %, 8 Ω)
-
50" Plasma Display Model: PRO-1140HD 1365 × 768 pixels 13 W + 13 W (1 kHz, 10 %, 8 Ω)
-
Similar Questions
Flashing Pixels
My Pioneer PureVision PRO607PU 60" Plasma TV has flashing pixels. can the flashing pixels be fixed?
My Pioneer PureVision PRO607PU 60" Plasma TV has flashing pixels. can the flashing pixels be fixed?
(Posted by meganzmom 9 years ago)
Pioneer Elite Plasma Tv Pro-ro4u No Signal With Satellite Conection
(Posted by jadgjust4u 10 years ago)
My Tv Does Not Turn On
Our PRO 800HDI stopped working yesterday. It has power...I unplug and plug it back in and the green ...
Our PRO 800HDI stopped working yesterday. It has power...I unplug and plug it back in and the green ...
(Posted by ahaddad 11 years ago)
My Pioneer Plasma Tv Does Not Turn On
I press POWER on the Media Receiver. The power indicator on Media Receiver lights up red. Then I pr...
I press POWER on the Media Receiver. The power indicator on Media Receiver lights up red. Then I pr...
(Posted by lekountd 12 years ago)
My Pioneer Pdp-505hd Turned Off In The Middle Of Viewing A Program.
When trying to turn TV on again the green light goes to the red standby light and does not turn on. ...
When trying to turn TV on again the green light goes to the red standby light and does not turn on. ...
(Posted by Anonymous-48631 12 years ago)