Ridgid K-380 Support Question
Ridgid K-380 Support Question
Find answers below for this question about Ridgid K-380.Need a Ridgid K-380 manual? We have 1 online manual for this item!
Question posted by mrdirect505boy on February 27th, 2013
Ridgid K380 Switch Wiring
how do i wire the switch on a k380 my kid pulled all the wires off,there are ten prongs on the switch
Current Answers
Related Ridgid K-380 Manual Pages
Owners Manual - Page 1
Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury. Failure to understand and follow the contents of this tool.
pág. 27
WARNING! K-380 Drain Cleaning Machine
OPERATOR'S MANUAL
• Français - 13 • Castellano -
Owners Manual - Page 2
...380 Drain Cleaning Machine
Table of Contents
Recording Form for Machine Serial Number ...1
General Safety Information Work Area Safety ...2 Electrical Safety...2 Personal Safety ...2 Tool...Damaged or Worn Cable ...9 To Install Replacement Cable ...9
Accessories Cable Selection ...10 Additional Tools Available for 3/8″ & 1/2″ Cable ...10
Maintenance Instructions Lubrication ...10 Autofeed...
Owners Manual - Page 3
K-380 Drain Cleaning Machine
K-380 Drain Cleaner
Record Serial Number below and retain product serial number which is located on nameplate. Serial No.
Owners Manual - Page 4
...8226; Use only three-wire extension cords which have the switch ON invites accidents.
• Remove adjusting keys or switches before plugging in personal injury.
2
Ridge Tool Company Replace damaged cords... to carry the tools or pull the plug from the user. Reduces the risk of inattention while operating power tools may result in . Never remove the grounding prong or modify the plug...
Owners Manual - Page 5
... to follow the contents of the tool.
K-380 Drain Cleaning Machine
• Do not over-reach. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must control foot switch and cable.
• Use foot switch to control.
• Check for appropriate conditions.
Tools are dangerous in serious injury.
•...
Owners Manual - Page 6
... on the cable. Equipment -
Description, Specifications and Standard Equipment
Description
The RIDGID K-380 Drain Cleaning Machine will cause the drum to 4″ in diameter and ... Core (Integral
Wound) Cable - Other uses or modifying the drain cleaner for disconnecting tools. T-260 Tool Set
K-380 Machine w/Gloves & Std. The integral wound cable has a quick change coupling system for...
Owners Manual - Page 7
... present and attached to the OFF position (Figure 4).
2. Place the mounting bracket onto the back of the K-380 using the two (2) 5/16″ x 1″ flat head screws. Directional Switch In OFF Position
Ridge Tool Company
5 K-380 Drain Cleaning Machine
Machine Assembly
WARNING To prevent serious injury, proper assembly of the Drain Cleaner is secure...
Owners Manual - Page 8
K-380 Drain Cleaning Machine
3. Lubricate ...the nature of sewer inlet. Position the air foot switch pedal for wear and damage. The T-Slot Coupler allows the tool to prevent fingers being caught between the belt guard ...been replaced.
4. The style of the tool is left up to the operator.
6. If the plug has been modified, is missing the grounding prong or if the cord is properly fastened...
Owners Manual - Page 9
...Do not touch plug with two gloved hands and pull approximately 1 foot of additional cable out of machine,...prong plug similar to catch backed up water. Ridge Tool Company
7 doors. • The cord has sufficient wire...around the cable, causing serious injury. K-380 Drain Cleaning Machine
the clear path selected ...
• Keep hands away from the foot switch.
• Hand must be stuck in order...
Owners Manual - Page 10
... the drain.
Neutral
Full Advance
Full Retrieve
Figure 7 - Autofeed
5. Repeat this condition by pulling back on the feed lever. If motor turns but the motor and its drum continue to... cutting tool hits a snag and stops turning, but the drum stops, the torque limiter is just inside sewer inlet. Once obstruction is encountered. Move FOR/OFF/REV switch into machine. K-380 Drain ...
Owners Manual - Page 11
...tool is dislodged and drum has stopped rotating, place FOR/OFF/REV switch...switch pedal and allow machine to come to clean cable and tool as you feed the cable into machine.
Pull...tool from sewer line, move the feed lever in REV (reverse) for any other purpose. Pull remaining cable and tool...if the cutting tool hits a ...Reverse Position
Ridge Tool Company
9 Tighten...tool and the nature...
Owners Manual - Page 12
... 1/2″ x 50′ w/Solid Core Cable 1/2″ x 75′ w/Solid Core Cable
Additional Tools Available For 3/8″ & 1/2″ Cable
Catalog No.
62990 62995 63000 54837 63005 63010 63020 63025 63030...of cable become hazardous when used on the K-380. Coil Cable Into Drum As Shown
2. Accessories
WARNING Only the following RIDGID products have been designed to prevent damaging effects...
Owners Manual - Page 13
... these instructions may create a risk of your nearest Independent Authorized Service Center, contact the Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com
Ridge Tool Company
11 All repairs made by an authorized RIDGID service technician.
K-380 Drain Cleaning Machine
Machine Storage
WARNING Motor-driven equipment must be kept indoors or well...
Owners Manual - Page 14
...acid. Motor switched to 4″ lines.
Wiring Diagram
12
Ridge Tool Company Cable is being ...380 Drain Cleaning Machine
Chart 1 Trouble Shooting
PROBLEM
POSSIBLE REASONS
SOLUTION
Cable kinking or breaking.
Cable worn out. Let the cutter do the work. Use 1/2″ cables in motor.
If no problem found with pedal or hose, replace diaphragm switch...
Similar Questions
Do You Have Picture Of Your Wheel Kit. Ridged K-380
Wheel kit for K-380, picture please, cost with shipping to 74467 also please would you have a auto f...
Wheel kit for K-380, picture please, cost with shipping to 74467 also please would you have a auto f...
(Posted by mitchintulsa 2 years ago)
Is There A Wiring Diagram For The R4510 Switch Actuator?
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
(Posted by djzinnicker 3 years ago)
How To Connect The Belt What Two Points Of The K-380 Machine Are Belt Pulleys
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
(Posted by popsrea1 9 years ago)
I Need A New Micro Switch For A Rigid K-380 Septic Sewer Drain Snake, Help?
I need a new micro switch for a Rigid K-380 septic sewer drain snake, Help?
I need a new micro switch for a Rigid K-380 septic sewer drain snake, Help?
(Posted by milesbarnettfamily 11 years ago)