Ridgid MS255SR Support Question

Find answers below for this question about Ridgid MS255SR.
Need a Ridgid MS255SR manual? We have 1 online manual for this item!

Ridgid Overview Questions Manuals Reviews Videos Research

Question posted by chstrees on March 17th, 2015

Lasers Useless - Suddenly

When I began using the saw the lasers created two lines, suddenly, they now create two spots that do not shine where the wood is against the fence, but nearly straight down. I opened up the cover over the laser and couldn't see any adjustment to allow them to shine along the blade, nothing seemed out of place, Any thoughts? Saw is basically useless without the laser guides and I am in the middle of project!!

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on March 17th, 2015 10:03 AM

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,397

90
points

Be sure the lasers aren't covered with wood dust.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Ridgid MS255SR Manual Pages

Operation Manual - Page 1

OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR � WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a RIDGID product. 1-866-974-3443/USA SAVE THIS MANUAL FOR FUTURE REFERENCE

Operation Manual - Page 2

table of contents General Safety Instructions 2 Specific Safety Instructions 3 Additional Instructions for Safe Operation 4 Symbols 5 Electrical 6 Lasers 7 Glossary 7 Features 8 Tools Needed 11 Loose Parts 11 Assembly 12 Adjustments 13 Operation 18 Maintenance 31 Troubleshooting 33 Warranty 34

Operation Manual - Page 3

...a combination of using an extension cord, be sure to use one that is heavy enough to carry the current that your product will cause a drop in line voltage, resulting ... . • Use the right tool. Wear protective hair covering to rain. W. Read this miter saw works. When using common sense, staying alert, and knowing how your miter saw and how to use it frees both hands...

Operation Manual - Page 4

...; Do not use blades with soap and water. Solvents could dissolve or otherwise damage the material. • Do not turn the tool off rapidly. Should this type of work. Always lock the saw arm in the "DOWN" position and then carry the saw by gripping the cutting handle or the miter fence. To reduce your...

Operation Manual - Page 5

... may cause serious and permanent respiratory or other part that the operator of the saw wears. • Inspect the tool cords periodically and, if damaged, have these instructions. Additional Instructions for Safe Operation �WARNING: The use of this tool can generate and/or disburse dust, which is marked to comply with ANSI Z87...

Operation Manual - Page 6

... construction Per minute Revolutions, strokes, surface speed orbits, etc., per second) Power Type of current Type of characteristic of the following symbols may be used on this tool. Read the operator's manual Eye protection To reduce the risk of these symbols will result in damp locations. No hands symbol Failure to keep...

Operation Manual - Page 7

... risk of grounded outlet box • If operating a power tool in damp locations is intended for indoor use power tools in wet or damp locations. The following signal words and meanings...tool's data plate. This compound miter saw is a double-insulated tool. �WARNING: Double insulation does not take the place of any power tool can result in the outlet properly, reverse the plug. Cover ...

Operation Manual - Page 8

...using the tool. Only turn the laser beam on when the laser will increase eye hazard. • The laser should be used and maintained in laser light. operator's glossary of the work piece. • Freehand Cut: Performing a cut without using a fence... piece from which the saw emits the laser light. Do not perform any parts of the main switch for laser use are acceptable. Any repairs...

Operation Manual - Page 9

...lines on the left Bevel 45°: Maximum nominal lumber size: Cutting Capacity of Crown Molding Miter 45° Left & Right: Maximum size: Net Weight 120 V~ 60 Hz 15 A 3,600 RPM 10 in. 5/8 in the Miter Saw's table that the saw... on which a blade or cutting tool is performed. FEATURES SPECIFICATIONS Motor No-load Speed Blade Diameter Arbor Size Laser Cutting Capacity with Miter at 0°...

Operation Manual - Page 11

...wood stock. 10 Right bevel range control LEVER With the right bevel range control lever "up" the head assembly can tilt both right and left. Fig. 2 LOWER BLADE GUARD The lower blade guard is made of shock-resistant, translucent plastic that shines...; left or right fence or base to securely...tool and in the saw's base. MITER-DETENT LOCKING LEVER The miter-detent locking lever, when used...

Operation Manual - Page 12

... following tools (not included) are included with your sliding compound miter saw: • Dust Bag • Blade wrench • Hex key • Work piece clamp • Operator's manual Blade wrench Combination square 3/8" Open-end wrench Fig. 3 OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR Dust bag Hex key � WARNING: The use of...

Operation Manual - Page 13

... fence during operation of this manual. Carefully check the workbench after mounting to secure the saw. Never operate the saw without checking for interference between the blade and the miter fence....this tool or create accessories not recommended for use with nails or screws. Trace holes at these locations for hole pattern Saw base 12 Trace holes at these locations for use with the saw ...

Operation Manual - Page 14

... result in accidental starting causing serious injury. 2. Set the bevel and miter angles to the fence, and readjust if necessary. NOTE: If the saw has not been used recently, verify that the miter-detent locking lever is secured at the zero position, making sure that the blade is ideal for dust collection. Dust...

Operation Manual - Page 19

... scrap wood. 3. Plug the saw into one of the two receptacles in the base behind the fence. It may interfere with side shields. � WARNING: Before each use if damage is observed or suspected. � WARNING: Always wait for the blade to stop completely, and unplug the tool before using the laser light. 1. Lock the saw , turn the laser...

Operation Manual - Page 21

HOW TO USE THE DUAL LASER LINE Fig. 20 1. Press the laser On/Off switch to "On" to better support the work pieces. On/Off trigger switch Fig. 20 Lock off button will engage the safety switch automatically. OPERATION UPPER SLIDING FENCE/LOWER ADJUSTABLE FENCE � WARNING: Unplug the saw , press the lock-off button to disengage the...

Operation Manual - Page 22

... is clamped firmly against the table and the fence. Loosen the slide-lock knob. 4. CHOP CUTS Chop cuts are used mainly for narrow pieces. Properly position the work piece. Plug the saw into an electrical outlet. 5. Before turning the saw on , lower the saw arm. � WARNING: Use a clamping position that does not interfere with the...

Operation Manual - Page 23

... � WARNING: Use a clamping position that no problems will stop before making a cut . A straight crosscut is warped, place the convex side against the fence. detent locking lever ... before returning the saw arm in between the dual laser lines. 11. Wait until it to the desired angle, using either left or right by lowering the saw table and fence. Push (but...

Operation Manual - Page 24

...straight bevel cut is made. 13. Unplug the saw. � WARNING: Failure to secure the saw arm in position. � WARNING: Loosen the sliding fence, and adjust the lower fence. Failure to do so could result in darker areas. Lift the bevel-lock lever and tilt the saw... the dual laser lines. 10. Use the work piece with the miter table set at the 0° position and the saw arm set ...

Operation Manual - Page 26

...line between the dual laser lines. 12. When the saw arm has been set from the blade. To make a test cut in scrap material before making a finish cut and jam the blade. 11. Place the work piece. � CAUTION: Never use... movement of 48°). 8. without holding the work piece against the fence, the board could grab the work piece that no problems will occur when the cut ...

Operation Manual - Page 36

... motor housing. The model number of this tool is found on a plate attached to provide all relevant information when you call 1-866-974-3443. Please record the serial number in the space provided below. OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR CUSTOMER SERVICE INFORMATION For parts or service, call...