Ridgid OL50145MWD Support Question
Ridgid OL50145MWD Support Question
Find answers below for this question about Ridgid OL50145MWD.Need a Ridgid OL50145MWD manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by Odin on December 2nd, 2017 10:31 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,670
Member since:
April 10th, 2010 Points: 41,236,670
Review the various suggested solutions for the first two PROBLEMs at https://www.manualslib.com/manual/140961/Ridgid-Ol50145mw.html?page=17.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Ridgid OL50145MWD Manual Pages
Operation Manual - Page 3
...to comply with ANSI Z87.1. glasses that provide protection against flying particles
Following this tool.
Service or maintenance performed by the operator and others in unexpected situations. Some.... Damaged cords increase
and debris may result
sense when operating a power tool.
Tools are doing, and use tool
in an open drain valve to decompress tanks and allow water to drain...
Operation Manual - Page 4
....
Before further use of obstructions or snags. GENERAL SAFETY RULES
When servicing a tool, use the next heavier gauge. Store indoors.
Inspect tanks yearly for an extension cord...61550; Always disconnect the air supply and power supply before making adjustments, servicing a tool, or when a tool is recommended for rust, pin holes, or other part that is in doubt, ...
Operation Manual - Page 6
... that may result in property damage.
WARNING:
The operation of risk associated with ANSI Z87.1.
Call RIDGID® customer service for repair. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields. We recommend Wide Vision Safety Mask for use this product.
CAUTION:
Indicates a potentially hazardous...
Operation Manual - Page 7
...are working area.
WARNING:
Keep the extension cord clear of the working with a power tool.
If damaged replace immediately. Repair or replace a damaged or worn cord immediately. Only ...electric cord having an equipment-grounding conductor and a grounding plug. Before using a power tool at a considerable distance from the power source, use . Electrical Connection
This product is...
Operation Manual - Page 8
... off. Pressure Regulator Knob
Regulates the outgoing pressure from the air tank to the tool.
The actual psi is in pressure. Pressure Switch
Automatically controls the on the compressor... the air.
Cut-Off Pressure
The high pressure at which the motor will not automatically start and control the compressor unless the manual On/Off Switch is measured by rotating the pressure...
Operation Manual - Page 10
... the product and any parts are damaged or missing, please call 1-800-4-RIDGID for use with this product. Failure to comply could result in accidental starting and possible serious personal injury. SORTIE
10
Failure to possible serious personal injury. WARNING:
Do not connect to power supply until assembly is misuse and...
Operation Manual - Page 12
...back on when the designated tank air pressure drops below : Operating some air-powered tools Operating air accessories such as previously instructed.
12
n Rotate pressure regulator knob fully ...hose with air in objects being thrown into the coupler until start-up has been completed. Match hoses, connectors, air tools, and accessories to do so could result in tank -...
Operation Manual - Page 13
... Turn the switch ON ( l ). turning counterclockwise reduces air pressure at the outlet; Check the tool manual to avoid damage to release until tightly closed.
13 NOTE: Always use your application.
n... valves clockwise until pressure gauge reads less than this operation for your air-powered tool. n Connect the power cord to desired line pressure. Turning the knob clockwise increases...
Operation Manual - Page 15
.... Therefore, no further lubrication is routinely checked for extended work with side shields during power tool operation or when blowing dust.
MAINTENANCE
WARNING:
When servicing use .
As a routine part ..., and allow unit to cool to remove dirt, dust, oil, grease, etc. Electric tools used on these materials, it is also advised that the oil is required.
replacing THE SEMI...
Operation Manual - Page 17
...
Check for assistance Take compressor to service center Decrease air usage; Excessive moisture in discharge air Compressor runs continuously
Excessive water in tank - Check for tool's requirement
Replace piston rings; TROUBLESHOOTING
problem
cause
solution
Compressor will not run or runs Low voltage
Check with voltmeter
slowly
Wrong gauge wire or length...
Operation Manual - Page 18
... should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at no charge to three years from misuse, abuse, neglect, alteration, modification or...to the dealer from state to the RIDGID® website at retail and may return the tool to an authorized service center for RIDGID® branded Air Compressors. One World Technologies, ...
Similar Questions
Kj3100 Not Starting
My KJ 3100 won't start after several attempts it's bin working for a month but trying to start up no...
My KJ 3100 won't start after several attempts it's bin working for a month but trying to start up no...
(Posted by myrieboris 1 year ago)
On/off Switch Cover Removal
It looks like my electrical wires are loose coming into the on/off switch. How do I remove the switc...
It looks like my electrical wires are loose coming into the on/off switch. How do I remove the switc...
(Posted by grfern50 7 years ago)
Stop Pin Wont Stay Locked In Down Position
does anyone else have this problem
does anyone else have this problem
(Posted by Robpino33 7 years ago)
When I Start It It Just Turns Off
I have a green light when i switch it on but when i start it it just turns off?
I have a green light when i switch it on but when i start it it just turns off?
(Posted by thomas20792 8 years ago)