Ryobi RTS10 Support Question
Ryobi RTS10 Support Question
Find answers below for this question about Ryobi RTS10.Need a Ryobi RTS10 manual? We have 4 online manuals for this item!
Question posted by mattharbaugh on October 27th, 2013
Rts10 Dado Throat Cover
I need a dado throat cover for a Ryobi RTS10 table saw
Current Answers
Related Ryobi RTS10 Manual Pages
English Manual - Page 2
... or materials by other than those specifically stated in any RYOBI® power tool which vary from the date of the original purchase. Batteries are limited to maintain and operate. You can obtain the location of Terms...9 Features...10-12 Tools Needed...13 Loose Parts...14-15 Assembly...16-19...
English Manual - Page 3
...marked "W-A" or "W". Also wear protective hair covering to disconnect from heat, oil, and sharp edges.
When operating a power tool outside, use it comes to operate tool.
DON'T OVERREACH. Check for a... to see that it was designed.
USE RIGHT TOOL. The use , before turning it on the saw 's applications and limitations as well as the specific potential hazards...
English Manual - Page 4
... worn cord immediately. Stay constantly aware of cord location and keep it well away from lumber before connecting to whether the tool is the equipment-grounding conductor. Always use blades with saw is rotating. Do not use a clean cloth when cleaning. Inspect for safe use blade washers or blade bolts that accept...
English Manual - Page 5
...; PROVIDE ADEQUATE SUPPORT to the rear and sides of the saw .
ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when reconnecting to power supply.
THIS TOOL should have a straight edge to instructions on all fences and auxiliary tables before it must always be replaced only by the manufacturer or...
English Manual - Page 6
...Hz
Hertz
W
Watt
Frequency (cycles per minute
Wet Conditions Alert
Do not expose to operate the tool better and safer.
To reduce the risk of injury, user must read and understand operator's manual...current
Direct Current
Type or a characteristic of the following symbols may be used on this tool. Safety Alert No Hands Symbol Hot Surface
Precautions that involve your hands away from the...
English Manual - Page 7
... with side shields and, when needed, a full face shield.
SYMBOLS
The following signal words and meanings are intended to explain the levels of any power tool can result in death or serious...product until you return the product to the nearest AUTHORIZED SERVICE CENTER for assistance. Call Ryobi customer service for repair. We recommend Wide Vision Safety Mask for use this product. ...
English Manual - Page 8
...AC only (normal household current), 60 Hz. An undersized extension cord will overheat. This tool is equipped with a damaged cord since touching the damaged area could cause electrical shock ...of electric shock. If the saw does not operate when plugged into a matching outlet that is able to overheat.
Electrical Connection
This tool is designed for electric current...
English Manual - Page 9
... Material The item on which a blade or cutting tool is mounted.
Resaw A cutting operation to reduce the...movement.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is ...the workpiece (requires a special blade).
Dado Cut A non-through the thickness of the saw blade tooth is not properly supported.
...
English Manual - Page 11
... through the table, surrounded by an insert called the throat plate. SPREADER - FEATURES
KNOW YOUR TABLE SAW
See Figure 2. The safe use the tool.
11 OVERVIEW
The upper portion of the saw has an...pawls (also a part of the blade. Kickback is thrown back toward the operator. This saw table, the easy-toread scale provides precise measurements in personal injury.
Place the key in these ...
English Manual - Page 12
...the switch key. Your table saw is equipped with your saw turned OFF, pull the switch key from accidentally starting , Always make sure your saw: With the saw . TO TURN YOUR SAW ON: With... blade styles of accidental starting when power returns. This feature is intended to start the tool. To lock your workpiece is not in a safe, secure location. FEATURES
BLADES
For ...
English Manual - Page 13
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and making adjustments:
WRENCH (2) 10 mm, 12 mm
PHILLIPS SCREWDRIVER
flathead SCREWDRIVER
FRAMING SQUARE
Fig. 4
13
English Manual - Page 16
...securely mounted to a workbench or an approved leg stand.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with the legs wide end up. (Upper braces have ... dimples on the leg align with a wrench.
Install a foot to make sure the table saw on two legs. Add hardware and finger tighten.
Use the same steps to the blade. TO ...
English Manual - Page 18
... turning the blade adjusting handle
clockwise.
Loosen the screws in the throat plate. Lift the throat plate and spacers from the saw. To reinstall the throat plate, place the spacers of the blade. NOTE: If the bevel lock lever needs to be tightened further, pull the spring-loaded lever out and rotate...
English Manual - Page 19
....
Securely tighten the bolt using the socket head cap screws, flat washers, and external tooth lock washers as needed .
If the blade guard assembly is needed to align the spreader with the saw then raise the blade guard assembly.
Loosen the socket head cap screws holding the spreader to install and...
English Manual - Page 20
... a handle fastened by a qualified electrician. Note: This table saw Failing to make cuts with great force and speed. Knock out any loose knots with tools to use the rip fence when rip cutting and the ...the blade teeth should it is sufficient to avoid the risks. Basic Operation of the TABLE Saw
The 3-prong plug must be plugged into knots or nails in a balanced position to...
English Manual - Page 29
...if your hands when making any part of serious injury.
When the cut is covered by removing the two
socket head cap screws, lock washers, and flat washers. ...through cuts can be made , turn the saw ON. Feed the workpiece into the power source. Turn the saw OFF. Fig. 32
29 Non-through cut . DO NOT install dado blades on straight cross cuts before removing ...
English Manual - Page 30
...making finish cuts in the OFF position. If the cuts
are needed.
The clamp screw on the rear of the rip fence. ...cuts in scrap wood before beginning any adjustment, make sure the tool is unplugged from the power supply and the switch is in...injury.
ADJUSTMENTS
WARNING:
Before performing any operation.
Unplug the saw then remove the blade guard assembly.
Unlock the rip ...
English Manual - Page 32
... only identical Ryobi replacement parts.
cally apply paste wax to them and buff to remove dirt, dust, oil, grease, etc.
To remove or change the blade
See Figure 36. Unplug the saw. Remove the screws holding the throat plate in this tool are pointing down toward the front of the table. Attach...
English Manual - Page 34
... provide all pertinent facts when you have purchased your tool, should a need ever exist for repair parts or service, simply contact...the model number and serial number in . Table Saw
BTS12S
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities ...8226; SERIAL NUMBER
BTS12S
RYOBI® is a registered trademark of Authorized Service Centers.
• MODEL ...
Repair Sheet - Page 3
...WARNING LABEL........ 1
21 411062701 NUT (1/4-20 CHEESE HD.)........ 9 22 410162003 SCREW (M6 x 18 mm CHEESE HD.)...... 3 23 A101014304 BRACKET ASSEMBLY 1 24 089015001002 SAW TABLE 1 25 0101010301 THROAT PLATE INSERT 1 26 410192001 SCREW (M4 x 10 mm TRUSS HD.)......... 2 27 0101141303 RUBBER WASHER 2 28 412012030 WASHER 2 29 414011002 SPRING PIN 1 30 410102702...
Similar Questions
Dado Blade Insert For A Ryobi Rts10 Table Saw
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
(Posted by bstilton 9 years ago)
