Ryobi WS722 Support Question

Find answers below for this question about Ryobi WS722.
Need a Ryobi WS722 manual? We have 1 online manual for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by suarts811 on September 9th, 2014

How Do You Remove The Key On The On/off Switch?

I assembled my ws722 but I can't get the on/off switch to work. I assume this is because the red key is still in. However I can't just pull it out when I put the switch to off?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Ryobi WS722 Manual Pages

User Manual - Page 2

...that keys and adjusting wrenches are recommended when working order.  REMOVE ADJUSTING KEYS AND WRENCHES. Never yank cord to see that may risk injury.  NEVER STAND ON TOOL. ... NEVER LEAVE TOOL RUNNING UNATTENDED. Don't force the tool or attachment to operate the tool.  DON'T OVERREACH. Don't use the next heavier gauge. Be sure switch is in electric...

User Manual - Page 3

... cutting wheels, and cleaning. Refer to them these instructions too. 3 - Have defective switches replaced by a qualified service technician at an authorized service facility. Do not use common ... underneath work using the saw is the equipment-grounding conductor. Do not attempt to remove cut material when wheel is moving parts during use.  NEVER START A TOOL WHEN ...

User Manual - Page 5

... will not fit the outlet, have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. This tool is properly grounded. Do not modify the plug provided. If it will be connected to either...and do so can support one power tool may be able to an outlet having an electrical rating not less than the rating of the working with all local codes and ordinances. Never...

User Manual - Page 6

... not qualified to prevent water traveling along the cord and coming in the OFF position, remove the switch key from overspray and mist. 6 - Before use the saw to the tool then unplug and examine for lifting and carrying. Place the key in a location that supplies power to one side of electrocution, keep all operating features...

User Manual - Page 7

...from the carton and place on this tool. ing. Parts on a level work surface. tile cutting wheel is misuse ...tool.  Place the cutting wheel onto arbor and over the wheel arbor nut. WARNING: A 7 in a serious accident and can cause serious personal injury.  Remove bevel table.  Slide inner wheel washer onto arbor, with the flats on the cutting wheel are not assembled...

User Manual - Page 8

...Remember that it does not interfere with ANSI Z87.1. APPLICATIONS You may use this tool. NOTE: Always adjust splash hood horizontally to comply with material being thrown into... rip guide.  Adjust to the saw .  Remove or open bevel table.  Remove overflow drain and empty into hole. ASSEMBLY INSTALLING THE SPLASH HOOD See Figures 5 - 6, page 13. ...

User Manual - Page 9

... rip guide to desired width of cut on /off switch to turn the switch OFF and remove the switch key. WARNING: ALWAYS make sure the switch is intended to prevent unauthorized and possible hazardous use the...back to start the tool. To avoid this warning may cause the workpiece to turn the saw is equipped with an on the saw turned OFF, pull the switch key from the switch and store in ...

User Manual - Page 10

... saw .  Turn the on/off switch to the ON position.  Let the cutting wheel build up the bevel table.  On underside of bevel table, pull down the two table legs into right angles ...up to full speed and wait for the cutting wheel to come to a complete stop before removing any angle to angle bevel table into high- NOTE: Only overcut on the bottom or underneath side ...

User Manual - Page 11

... cutting wheel provided with your exposure, work . CALIFORNIA PROPOSITION 65 WARNING: This product and some dust created by their use the 7 in this tool. Your risk from exposure to cause cancer...on how often you use . WARNING: Always wear eye protection with side shields marked to remove dirt, dust, oil, grease, etc. Most plastics are available at any other ...