Singer Futura Quartet Support Question
Singer Futura Quartet Support Question
Find answers below for this question about Singer Futura Quartet.Need a Singer Futura Quartet manual? We have 1 online manual for this item!
Question posted by keithgutter on April 20th, 2013
What Else Can Be Done If Ur Machine Keeps Stopping And You Have Already Cleaned
my machine keeps stopping . i have cleaned bobbin carraiage .
Current Answers
Related Singer Futura Quartet Manual Pages
Instruction Manual - Page 1
...sewing 49 Performance checklist 50 Cleaning hook area and feed dogs 51 Oiling inside the face cover 52 Special accessories 53 Helpful messages 54 - 55
For European version
Sewing machine... OF CONTENTS
1.GETTING TO KNOW YOUR MACHINE Machine identification 2 Accessories 3 Setting up your machine 4 Spool pins 4 Winding bobbin 5 Threading the bobbin thread 6 Threading the top thread 7...
Instruction Manual - Page 3
...Bobbins
3. Button sewing foot
1
16. The Satin Foot (14) is another
12
very useful foot and should be
used for most decorative sewing. To install the FUTURA software, refer to the CD insert for needle plate
10. Auxiliary spool pin
4. Buttonhole opener/Brush
9. Screwdriver (large)
11. Embroidery software CD
19
FUTURA...
Sewing machine is "system" of your
sewing....
Instruction Manual - Page 4
...Place felt disc over it. Set power/light switch at "OFF"
machine socket
2 1
Pin
3
POWER/LIGHT SWITCH
Your machine will not operate until the power/light switch is turned on the... plug of thread. NOTE: In sewing mode, the machine can be disconnected from the walloutlet.
When servicing the machine, or when changing needles or lights, etc., the machine must be operated
either with a...
Instruction Manual - Page 6
...
B
A
6 NOTE: Sewing can be started without having to pull up sufficiently to allow you to the left . Insert the bobbin making sure the bobbin rotates counterclockwise when you ).
2. THREADING THE BOBBIN THREAD
1. Raise the needle... plate until it stops in the slot (B). NOTE: This is pulled.
4. Then pull the thread along the groove on the top left .
5. Remove the bobbin cover plate by...
Instruction Manual - Page 8
... cutter/holder
4
Threading lever
8 Pull thread gently into the twin thread guides (A and B).
3. Make sure that
the machine be threaded automatically. Release the threading lever and needle will be set for the needle being used, then manually thread the ...to its lowest position until the twin thread guide rotates and stops. If it should not return to the thread guide on the needle bar.
Instruction Manual - Page 9
Felt disc
If the threading hook is used after a long interval.
5
HELPFUL SUGGESTIONS: Put a drop of sewing machine oil onto the felt disc,
if the machine is deviated from needle hole,
adjust the position of the hook using a small screw
6
driver.
If the threading hook cannot catch thread, adjust the vertical position by bending the twin thread guide.
9
Instruction Manual - Page 10
The following table is used in the bobbin as it toward you .
3. ...2. Tighten the needle clamp screw firmly with the flat side toward the back Always disconnect the machine from power supply by turning it can be of any fiber: cotton, linen, silk, wool,...90
blue band 16/100 purple band
* For best sewing results, always use a Singer Branded Needle. Raise the needle bar to its highest position...
Instruction Manual - Page 11
...less puckering when the upper thread appears slightly on top of the machine. Do this, however, only after you have determined that the machine is in the middle of layers of the fabric you do ...the needle is correctly threaded (see page 16 - 17). BOBBIN TENSION
The bobbin tension has been correctly set at the factory, so you are sewing. You will need to adjust the tension control.
Lower ...
Instruction Manual - Page 14
... carried out while the Reverse stitch button is operating. SPEED CONTROL LEVER
Sliding the lever sets desired sewing speed. NEEDLE STOP POSITION SELECTOR BUTTON
When the machine is turned on all patterns. The machine will be at the exact spot in reverse as long as a top speed limiter.
6
14 Tacking stitch function for straight...
Instruction Manual - Page 17
... indicate distance from the needle at rear side) G. Thread tension control B. Start/stop the sewing machine. Feed dog control (at its highest position, then raise the
6
presser foot....sewing a seam.
6. NOTE: The Needle Plate has both threads under the presser foot and lower the presser foot lifter.
5
4. KEEPING SEAMS STRAIGHT
To keep the seam straight, use one of the fabric, stop...
Instruction Manual - Page 25
... fabric along the edge of the stitch, being sewn, to check the stitch pattern to be used .
* Before starting to sew, check that there is enough thread wound onto the bobbin to cut into the stitching. Arrowhead on lapel In addition to using this stitch on garments and home dec projects. CRISS...
Instruction Manual - Page 38
... then follow steps 1 through 4 above.
38 Please wait for a moment, turn OFF your sewing machine. You can always abort the installation procedure by turning the Hand wheel towards you.
2. The ... unit.
3.
Turn on your desktop to your sewing machine and connect the USB cable between your large hoop. Double click on the Futura Icon on your computer.
Finally you are requested...
Instruction Manual - Page 39
... embroidery can be reversed all the way back to the machine. NOTE: When sewing designs created by checking the box in progress, press the Reverse Stitch button. To stop the machine, push the button again and the machine will stop sewing and the needle stops at "E" for 2 - 3 seconds shows that an incorrect operation was made. * Continuous flashing indicates...
Instruction Manual - Page 41
...stop
Blank stitches resulting from thread breakage
Reverse stitch button
2. Step back through the data until the blank area has been completely passed over the spool of thread may continue to embroider up to the point for continuing.
1. Computer screen says thread is broken, machine... lights are missing
If the embroidery machine...automatically stops. Restart the embroidery machine ...
Instruction Manual - Page 43
... 4/10th of a design be changed in the DESIGN/CHANGE SIZE menu in , the letter will keep the design integrity. Resizing individual letters
You can accept. So what most probably happens is usually the... the stitch count.
6. When sizing designs in the Futura software you have brought them into the hoop and exited the text window. The machine has a certain limit of a design
Left click and...
Instruction Manual - Page 44
...n o u g h t o accommodate the amount of smaller embroidery elements and/or lettering, that is too large for it and sew accordingly. Cross line Cross line
Please Note: a thin line is very important to three additional hoops will compensate for misalignment if the ...Futura QuartetTM software that will allow embroidery data which is larger than a single embroidery hoop to be sent to the machine...
Instruction Manual - Page 50
... not sew. * Power switch is too tight. - Clean hook. (see page 10). Replace needle. (see page 51). * Needle is not threaded correctly. (see page 12 - 13).
50 Fabric does not move. * Presser foot is caught in hook. - Replace needle. (see page 10). * Machine is damaged. - Clean hook. (see page 6). * Lint accumulates in bobbin case or...
Instruction Manual - Page 51
... it is necessary to remove dust from the wall-outlet. Replace the bobbin case with the lint brush.
4
Put one drop of your machine, it is not suited for removal.
3. DO NOT use "all times.
(1)
1. Use dry rags to keep sewing machine and footcontroller clean. NOTE: U se dry rags to its highest position and put
6
and...
Instruction Manual - Page 54
... PC screen
Problem Correction
Sewing Embroidery
Machine is detected on control panel and/or PC screen.
is locked up due to thread entangled around spindle or
○ ○ rotation interrupted forcibly. Turn off power switch and eliminate the problem that caused the
02
bobbin winder to stop . Bobbin winder is connected.
Disconnect...
Instruction Manual - Page 60
...persons in order to avoid a hazard." 6. Keep ventilation openings of the sewing machine and foot control free from the electrical outlet when...repair or replace at once." 21.
Close
cover
before cleaning." POLARIZED PLUGS CAUTION (USA & Canada only)
This...appliance by the manufacturer as threading needle, changing
needle, threading bobbin, or changing presser foot, etc." 18.
"If the...
Similar Questions
Where Can I Get Replacement Parts For My Futura Quartet 6000 Machine?
(Posted by treasuredjewels2321 8 months ago)
I Was Sewing And All Of The Sudden My Machine Turned Off
(Posted by mari0624 3 years ago)
We've Had This Machine For A Little Over A Year,first Time Trying To Use It. E
error code 01 comes up. Bobbin appears right, but the mentions rotation interupted forcefully. How d...
error code 01 comes up. Bobbin appears right, but the mentions rotation interupted forcefully. How d...
(Posted by dmislanders 4 years ago)
Singer Signature 7258 Sewing Machine .how To Fix Bobbin Filler
(Posted by faerygardens 9 years ago)
Singer Sew Mate Sewing Machine Where Is The Bobbin Access Cover
(Posted by jfbsus 10 years ago)