Stihl BT 45 Wood Boring Drill Support Question
Stihl BT 45 Wood Boring Drill Support Question
Find answers below for this question about Stihl BT 45 Wood Boring Drill.Need a Stihl BT 45 Wood Boring Drill manual? We have 2 online manuals for this item!
Question posted by BASURVEYING on May 17th, 2018
Why Does My Bt 45 Bog Down After Drilling Half Way Througn A Timber
It Seems To Run Fine But When You Put A Load On It It Bogs Down
Current Answers
Answer #1: Posted by Odin on May 17th, 2018 6:03 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
Possible causes:
- Dirty air filter
- Carburetor out of adjustment
- Contaminated muffler
If the problem persists (or if you require further explanation), you'll have to consult Stihl: use the contact information here--https://www.contacthelp.com/stihl/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Stihl BT 45 Wood Boring Drill Manual Pages
Instruction Manual - Page 3
...from your STIHL power drill, it is a high-torque, gasoline-powered tool, some special safety ...Adjusting the Carburetor
21
Checking the Spark Plug
22
Engine Running Behavior
23
Replacing the Starter Rope and
Rewind Spring
...Warranty
Statement
30
Trademarks
32
{
BT 45
English
Allow only persons who fully understand this manual. Because a power drill is important that you do ...
Instruction Manual - Page 4
.... N Lever (2) ... Indicates a hazardous situation which, if not avoided, could result in different ways: N A bullet marks a step or procedure. Careless or improper use may not be on your... characteristics or the appearance of your power tool.
Drilling into or contact with the symbols and signal words described below .
2
BT 45 Warning!
English
Guide to Using this Manual...
Instruction Manual - Page 5
...of a wood boring drill or a plant auger involves
1.
during a work , check with any power tool can result.... Prolonged use of your power tool run unattended.
See the appropriate section of the power tool. Tiredness may have any substance...BT 45
3
In order to property, never let your instruction manual for drilling wood. English
Warning! Use your power tool...
Instruction Manual - Page 7
... dangerous. English
Warning! THE USE OF THE POWER TOOL
Transporting the Power Tool
Warning! Warning! Remove the drilling tool before starting your power tool in fact, be extremely dangerous.
Do not smoke or bring any way. BT 45
5 Although certain unauthorized attachments, drills and augers are useable with STIHL power tools, their use with the hot muffler away from escaping...
Instruction Manual - Page 9
.... BT 45
7 Maintain good balance and secure footing. Wrap your fingers and thumbs around your hand or fingers and may cause arcing that the spark plug boot is damaged, improperly adjusted or maintained, or not completely or securely assembled.
For specific starting , particularly the throttle trigger, throttle trigger lockout, stop switch and drilling tool...
Instruction Manual - Page 10
Drilling Planting Holes
Drilling Holes in Wood
Working Conditions
Operate and start your power tool only outdoors in a tree or any other reproductive harm. For better footing, clear away fallen branches, scrub and cuttings. carbon monoxide) may be taken in slippery conditions (wet ground, snow) and in a cramped environment.
8
BT 45...such as the engine is running, this position to have...
Instruction Manual - Page 11
...wood), such as cable detectors and / or by the power tool away from the operator. In such a situation, some or all of the power drill... When drilling in heavy clay soil, bore about 1/3 way and ...BT 45
9 When the inhalation of certain dusts, especially organic dusts such as you to control sudden jolts and reactive forces. Stay clear of overhead electrical wires when backing the drilling tool...
Instruction Manual - Page 12
.... To reduce the risk of § 4442 or § 4443 or the Public Resources Code to repair damaged drilling tools. Use the specified spark plug and make a warranty claim for properly maintaining the
10
BT 45
Warning! In California, it and the ignition lead are always clean and in the neutral position N before putting...
Instruction Manual - Page 13
...be opened up the clamp slightly. Store your power tool in the clamp and allows the clamp to fire ...(1) by the clamp and turn it down firmly.
421BA005 KN
421BA036 KN
BT 45
11
Normal mounting procedure
N Hold the clamp firmly and unscrew the handle ...any maintenance of the machine. Mounting the Handles
Assist handle for wood drill
Before mounting a new assist handle for longer than a few ...
Instruction Manual - Page 14
...wood drill) and in the flange.
During operation, always hold the machine firmly with both hands to position 1. The tool speed is too high for drilling planting holes when the gearbox is properly seated (see arrow).
5
To change the drilling tool...KN
12
BT 45
N Push the flange onto the machine as far as stop and line it up.
Release the throttle trigger if the drilling tool jams.
The...
Instruction Manual - Page 15
... they are designed for use in or passing through the wood.
Use only STIHL two-stroke engine oil or equivalent high...running speed -
Take care when handling gasoline. Gasoline with an ethanol content of more than 10% can be avoided by the drilling tool jamming in both hands to another fuel with incorrect idle adjustment. To reduce the risk of personal injury from static
BT 45...
Instruction Manual - Page 18
... and the drilling tool used, the speed can be moved to suit requirements. Gearbox idle position for repair.
001BA226 KN 421BA017 KN
Gearbox
The power drill is running at idle speed - It may be necessary to turn the drilling spindle slightly before the rotary knob can be adjusted to the required position.
16
BT 45 High-speed...
Instruction Manual - Page 19
... release the planting hole auger.
BT 45
17 Fitting the Auger
Adapter for planting hole auger
N With the engine stopped (knob in N
position), place the machine on the
ground and make sure you remove the chuck key before starting up. N Secure the drilling tool (5) in positions 1, 2 and R, the drilling tool may only be started with a 19mm...
Instruction Manual - Page 22
...the air filter cover (2).
N Replace with both hands on the handles. N Install the filter in the drill hole
If there is a noticeable loss of engine power
421BA025 KN 421BA026 KN
421BA038 KN
N Let go ... throttle trigger. N Increase engine speed and slowly pull the drilling tool out of the filter housing (4).
or, as a temporary measure, knock it out or blow it down firmly.
20
BT 45
Instruction Manual - Page 23
... it 1 full turn the screw another 1/2 to adjust the high speed screw within fine limits.
N Turn the low speed screw (L) slowly
counterclockwise until the engine runs smoothly - It is idling N Turn the idle speed screw (LA)
counterclockwise until the drilling spindle stops rotating and then turn . carburation, ignition, timing and valve or port...
Instruction Manual - Page 27
... Run the engine until the carburetor is properly engaged. N Store the machine in a dry, high or locked location, out of the reach of fuel properly in accordance with frame in position -
BT 45... new spring with local environmental requirements.
The bits of 3 months or longer
N Remove the drilling tool.
To reduce risk of injury, wear eye and face protection and work gloves.
6
Storing ...
Instruction Manual - Page 28
...by dealer2)
All accessible screws and nuts (not adjusting screws)
Retighten
Antivibration elements
Check
X
Have replaced by dealer2)
Drilling spindle
Clean
X
Auger
Inspect
X
Replace
Safety labels
Replace
1) not in fuel tank
Check Replace
Fuel tank
Clean
Carburetor... monthly every 12 months if problem if damaged if required
X
X
X
X
X
X
X X
X
X
X
X
X
X
X
X
BT 45
Instruction Manual - Page 29
... Parts
7 3 1
2
12 13
4 6
5
11 14
9
8 10
15 18 19
16
17 22
21
English
1 Wood Drill2) / Twist Drill2) 2 Chuck1) 3 Assist Handle1) 4 Knob 5 Fuel Filler Cap 6 Air Filter Cover 7 Carrying Strap2)...18 Assist Handle1) 19 Muffler with Spark Arresting Screen 20 Spark Plug Boot 21 Drilling Spindle 22 Adapter for Planting Hole Auger
421BA040 KN
20
BT 45
1) Depending on Model 2) Special Accessory
27
Instruction Manual - Page 30
...Bore:
1.34 in. (34 mm)
Stroke:
1, 18 in. (30 mm)
Engine power to ISO 7293:
1.1 hp (0.8 kW) at front end of power drill.
19 Muffler with the ignition lead.
21 Drilling...Wood Drill / Twist Drill For drilling holes.
2 Chuck For gripping and securing wood drill or twist drill.
3 Assist Handle Front handle for wood drill for holding the power drill...the power drill.
11 ...Auger For drilling holes....
Technical Reference - Page 1
... 4. Technical description 2.
Service accessories and special tools 6. Spare parts
IP*
/ 13.2002/
a
STIHL BT 45 (for drilling wood)
STIHL BT 45 (for drilling planting holes
The newly developed STIHL BT 45 drill is a multi-purpose machine with a gasoline engine. Technical Information
New STIHL BT 45 drill - Series 4314
Contents 1. Set of parts and accessories 5. Specifications...
Similar Questions
Trimmer Head Locks Up
String trimmer Stihl FS 45 starts and idles just fine. When the throttle is advanced, the trimmer he...
String trimmer Stihl FS 45 starts and idles just fine. When the throttle is advanced, the trimmer he...
(Posted by aaflitetech 7 years ago)
Is There A Way To Dismantle The Cutting End Of The Drive Tube?
The motor works fine but the cutting end does not spin. something is disconnected in the drive tube ...
The motor works fine but the cutting end does not spin. something is disconnected in the drive tube ...
(Posted by mariaxczavala 8 years ago)
Stilh Fs 45 Service Repair Manual
where can I get a service repair Manual fot Stihl FS 45 FS 46?
where can I get a service repair Manual fot Stihl FS 45 FS 46?
(Posted by n7xsl48 8 years ago)
Looking For A Replacement Wand Handle. Mine Froze And Cracked In Half
(Posted by robseabolt 9 years ago)